GAS BreathSpec Manual de instrucciones

Quickstart Manual

BreathSpec®

G.A.S. Gesellschaft für

analytische Sensorsysteme mbH

BreathSpec® –Quickstart Manual

2/67

Version 1.01, February 2021

Valid from BreathSpec® Firmware Version 4.00

All data, texts, designs, images and other elements used in this user manual are

protected by copyright law. Any infringement may be subject to legal action.

Passing it on to third parties and producing copies of any kind or form –on the whole

or in parts - is not permitted without written agreement of G.A.S. Any infringement

may be subject to legal action.

G.A.S. reserves the right to realize technical changes to the product without explicitly

mentioning them.

BreathSpec® is a registered trademark. Any infringement may be subject to legal

actions.

The BreathSpec® does not have a medical approval.

CE-Marking according to:

International Standard EN ISO 17050-1:2004

Directive 2014/35/EU (Low voltage directive);

Directive 2014/30/EU (Electromagnetic compatibility);

Directive 2011/65/EU (RoHS);

Directive 2012/19/EU on waste disposal (Waste Electrical and Electronic

Equipment –WEEE)

G.A.S. Gesellschaft für analytische Sensorsysteme mbH

44227 Dortmund - Germany

G.A.S. Gesellschaft für analytische Sensorsysteme mbH

Otto-Hahn-Str. 15

D-44227 Dortmund

Germany

Phone: (+49) 231/9742-6550

Fax.: (+49) 231/9742-6555

E-Mail: [email protected]

Internet: www.gas-dortmund.de

BreathSpec® –Quickstart Manual 
 
3/67 
 
 
Table of Content 
 
1General Information ............................................................................................. 5 
1 Information about the Manual........................................................................ 5 
2 Explanation of Symbols................................................................................. 5 
3 Notation for dialogs, elements and references .............................................. 6 
4 Scope of Supply BreathSpec® with Circular Gas Flow Unit (Version 4G1)... 7 
5 Scope of Supply Special edition BreathSpec with Airsense µTD Unit (Version 
4G2) 12 
6 Liability and Guarantee................................................................................ 16 
7 Copyright..................................................................................................... 17 
8 Return and Disposal.................................................................................... 17 
9 Software Updates........................................................................................ 17 
10 Customer Service........................................................................................ 17 
2Safety................................................................................................................. 18 
1 Intended Use Only....................................................................................... 18 
2 Responsibility of Operator........................................................................... 18 
3 Requirements of Personnel......................................................................... 19 
4 Dangers....................................................................................................... 20 
3Transport, Packing and Storage ........................................................................ 21 
1 Inspection after Transport............................................................................ 21 
4Packing.............................................................................................................. 21 
1 Storage and Transport................................................................................. 21 
2 Cleaning and Maintenance.......................................................................... 22 
3 Cleaning...................................................................................................... 22 
4 Maintenance................................................................................................ 22 
5Installation BreathSpec® Device (Version 4G1) with Ciruclar Gas Flow Unit 
(CGFU)..................................................................................................................... 24 
1 Installation Requirements............................................................................ 24 
2 Installing the device..................................................................................... 25 
3 Mounting the Mouthpiece holder................................................................. 29 
4 Connecting the Mouthpiece tube................................................................. 30 
5 Installation of Luer-Lock adapter [optional].................................................. 34 
6 Prepare the device for operation ................................................................. 38 

BreathSpec® –Quickstart Manual 
 
4/67 
 
6Installation BreathSpec® Device (Version 4G2) with Airsense µTD .................. 42 
1 Installation Requirements............................................................................ 42 
2 Installing the device..................................................................................... 43 
3 Prepare the device for operation ................................................................. 49 
7System Operation .............................................................................................. 53 
1 Measurement Reqiurements....................................................................... 53 
2 Measurement Program................................................................................ 53 
3 Workflow: Breath Sampling via Handheld Breath Sampler.......................... 54 
3.1 Workflow: Installation of Disposable Reservoir Tube and Mouthpiece.. 54 
3.2 Workflow: Execute a breath measurement using the Handheld ........... 55 
4 Workflow: Breath Sampling via Disposable Breath Sampler ....................... 58 
4.1 Start a breath measurement using disposable breath sampler............. 58 
5 Workflow: Exemplary Breath sampling with a sample bag.......................... 61 
6 Workflow: Measurement in ID Input Mode................................................... 63 
8Appendix............................................................................................................ 65 
1.1 IMS-Spectrum Examples ...................................................................... 65 
2 Corresponding G.A.S. Documents and Tutorials......................................... 67 
 
 

BreathSpec® –Quickstart Manual

5/67

1 General Information

1.1 Information about the Manual

INFORMATION!

This Quickstart User Manual is an excerpt of the most important

information for installation and initial setup from the User Manual. It

is an addition to the User Manual and does not replace the User

Manual.

This manual describes a safe and adequate handling of the device. Following the

instructions of the indicated safety aspects and instructions as well as the national

and/or local rules and general safety regulations concerning the prevention of

accidents are absolutely imperative.

Before starting the work with the device read the manual completely and thoroughly

particularly the chapter security and respective safety references. Assure that you/the

operator comprehend the terms described.

The manual is part of the device. It must be stored together with and next to the

device at any time.

INFORMATION!

The graphics in this user manual are schematic and may differ from

the actual conditions. The firmware and PC software screenshots in

this user manual may differ from the actual conditions.

1.2 Explanation of Symbols

Important and safety-relevant references in this manual are characterized by

symbols. These indications which are in-line with industrial safety must be respected

and followed at any time.

INFORMATION

This symbol calls information, which are to be considered for

efficient and perfect handling of the equipment.

WARNING

This symbol indicates references, which can lead to damages,

malfunctioning and/or loss of the device.

BreathSpec® –Quickstart Manual

6/67

DANGER

This symbol marks references, which can lead to health

impairments, injuries, lasting body damages or to death due to

electric current.

DANGER

This Symbol marks paragraphs, which describe potential dangers and

damage due to exposure to radioactive radiation.

DANGER

This symbol marks references, which describe working procedures

that demand special attention to avoid spreading of biohazard

WARNING

This symbol marks references, which can lead to health impairments,

injuries due to pinching.

1.3 Notation for dialogs, elements and references

Example Dialog:

System › Connections › LAN File Transfer › Settings… › Test Connection

Example Elements:

Gas Out, Sample gas in

Example: References

Advanced User Manual, Chapter 5.1 Installation Reguirements

Example: Information

keep the transport box

BreathSpec® –Quickstart Manual

7/67

1.4 Scope of Supply BreathSpec® with Circular Gas Flow Unit

(Version 4G1)

Assure that you have received the full scope of supply. If there is any part missing,

please contact the GAS-hotline immediately.

Standard Scope of Supply

BreathSpec® Device (1 piece)

including connected Circular Gas Flow Unit

(CGFU) (1 piece)

Power supply with power plug (1 piece)

Mouthpiece Handheld holder arm with

screws

BreathSpec® –Quickstart Manual

8/67

Mouthpiece Handheld with

heatable Transferline

BreathSpec® Gas tube Kit (installed)

•Driftgas/Carriergas Adapter (1 piece)

•0,6 m 3mm PFA Tubes with 3 mm

Swagelok-Connector (2 pieces)

CGFU Connection cable (installed) (1 piece)

LAN Cable (1 piece)

BreathSpec® –Quickstart Manual

9/67

Luer-Lock Adapter-Kit

•Luer-Lock Adapter (1 piece)

•Luer-Lock Adapter Heater (1 piece)

Disposable Breath Reservoir Kit

•Mouthpieces (100 pieces)

•Reservoir tube (100 pieces)

Inner Syringe Body (2ml syringe) (50 pieces)

Sampling Syringe (5ml syringe) (100 pieces)

BreathSpec® –Quickstart Manual

10/67

BreathSpec® Blind plug Set (5 pieces)

(Swagelok 3mm Blind plug with red cap

installed on device connectors)

Torx Tool Kit

•Torx Srewdriver 8 mm (1 piece)

•Torx Srewdriver 10 mm (1 piece)

•Torx Srewdriver 30 mm (1 piece)

Document Map with Documents and Device

User Manuals

USB-Stick Box with Software und Documents

(1 piece)

Otros manuales para BreathSpec

Tabla de contenidos

Otros manuales de Instrumento analítico de GAS

GAS

GAS BreathSpec Manual de usuario

GAS

GAS GC-2013 Manual de usuario

GAS

GAS GC-IMS-SILOX Manual de usuario

GAS

GAS SF6-Aciditor Manual de usuario

GAS

GAS GC-IMS-ODOR Manual de usuario

Manuales populares de Instrumento analítico de otras marcas

Cocraft

Cocraft NLT04 Manual de usuario

M&C

M&C GENTWO PMA1000 Manual de usuario

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Manual de usuario

CONDTROL

CONDTROL XP4 PRO Manual de usuario

Extech Instruments

Extech Instruments BR200 Manual de usuario

Dewetron

Dewetron DEWE-30-16 Manual del producto

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Instrucciones de instalación y funcionamiento

RIDGID

RIDGID SeeSnake Compact Manual de usuario

Teledyne

Teledyne 3000PA Manual de usuario

YDLIDAR

YDLIDAR TIA Manual de usuario

Olympus

Olympus IPLEX FX Series Manual de usuario

Bosch

Bosch GLM 50 C Professional Manual de usuario

Reflecta

Reflecta DigiEndoscope Manual de usuario

Chinavision

Chinavision CVACZ-G696 Instrucciones de montaje

Fuji Electric

Fuji Electric ZKMA Manual de usuario

Teledyne

Teledyne 3300TA Manual de usuario

VOLTCRAFT

VOLTCRAFT IC-100HD Manual de usuario

RIDGID

RIDGID micro CA-25 Manual de usuario