GarrettCom Magnum ITS Blade Manual de usuario

Corporate Headquarters

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539

Phone: 510.438.9071

Fax: 510-438-9072

Web: www.GarrettCom.com

Email: support@Garrettcom.com

Magnum ITS Blade

Ethernet Switch for

2070 Traffic Controller Chassis

Installation and User Guide

www GarrettCom com

Magnum ITS Blade Hardened Switches for 2070’s Installation and User Guide (02/03)

Magnum™ITS Blade Ethernet Switch

for Model 2070 Traffic Controller Chassis

Installation and User Guide

Part #: 84-00133, (Rev A 02/03)

Trademarks

Ethernet is a trademark of Xerox Corporation

NEBS is a trademark of Telcordia Technologies

UL is a registered trademark of Underwriters Laboratories

GarrettCom, Magnum, Personal Hub and Personal Switch are trademarks of

GarrettCom, Inc.

Important: The Magnum ITS Blade Switches for Model 2070 Traffic

Controllers contain no user serviceable parts. Attempted service by unauthorized

personnel shall render all warranties null and void. If problems are experienced

with Magnum ITS Blade Ethernet “2070” Switch products, consult Section 5,

Troubleshooting, of this User Guide.

of this publication may be reproduced without prior written permission from

GarrettCom, Inc.

Printed in the United States of America.

www GarrettCom com

Magnum ITS Blade Hardened Switches for 2070’s Installation and User Guide (02/03)

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed below:

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

Email: [email protected]

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if not

installed and used properly, that is in strict accordance with the manufacturer's

instructions, may cause interference to radio communication. It has been tested and found

to comply with the limits for a Class A computing device in accordance with the

specifications in Subpart J of Part 15 of FCC rules, which are designed to provide

reasonable protection against such interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference, in which case the user at his/her own expense will be required to take

whatever measures may be required to correct the interference.

www GarrettCom com

Magnum ITS Blade Hardened Switches for 2070’s Installation and User Guide (02/03)

iii

MAGNUM

ETHERNET CONNECTIVITY PRODUCTS

"DESIGNED AND MANUFACTURED IN THE USA"

Overview

GarrettCom, Inc. offers the Magnum line of Ethernet LAN connectivity

products with industry-standard functionality. Magnum products are heavy

duty, feature fiber-built-in ports, and have AC and DC power options to make

them suitable for a variety of Industrial and Carrier Class applications.

6K25 Managed Fiber Switches, Gigabit, 100 and 10 Mbps, fiber and copper ports,

mix-and match. Features SFF fiber for up to 25 fiber ports in a 1U unit. Configurable.

4K-Series Switches, 100 and 10 Mbps copper ports with optional 100Mb fiber ports,

regular and Reverse rack-mount models, AC and DC power options, heavy duty specs.

Quad-Series Fiber Switches, 100 & 10Mbps, fiber and copper ports, mixed-speed and

mixed-media types, full switching performance, AC and DC power options.

P62-Series “Outdoor” Ethernet Switches, for temperature uncontrolled applications,

6 10/100 and 2 100Mb fiber ports, managed and unmanaged models, all fiber types.

Mixed-Media Fiber Hub, 16-port Stackable, 10/100 auto-sensing, AC and DC power

Dual Speed 8-port and 16-port Stackable, 10/100 auto-sensing. AC and DC power

cPCI

Blade

12-port 10/100 “hub-on-a-card” for Compact PCI chassis rear I/O

ITS

Blade

8-port 10/100 “switch-on-a-card” for Model 2070 Traffic Controllers

Stackable Hubs, SNMP Optional

10Mb series and 100Mb series, both w/ optional port modules, AC and DC power

Personal Switches, 10/100Mb

8 port dual speed, Auto-negotiable with fiber option

Personal Hubs, 100Mb or 10/100Mb

8-port, with two switched ports (1 fiber built in)

Personal Hubs, 10Mb series

8-port + AUI, stackable to 5 high, + optional BNC of fiber port

8 or 9-port and 4 or 5-Port Personal Hubs, w/ man. up-link sw.

Media Converters, 10Mb and 100Mb series, for offices and Hardened models for

industrial applications. All media combinations, incl. fiber ST, SC, mm., single mode

The “X-line” of configurable MiXed Media products:

Stackable Concentrators, SNMP optional, 13-Ports

Repeater Port Modules (RPMs),6 types for Ethernet media

Bridge Port Modules (BPMs), 4 types, for segment isolation

Transceivers, 10Mb series Mini-Transceivers and Coax Models Feb, 03

www GarrettCom com

Magnum ITS Blade Hardened Switches Installation and User Guide (02/03)

TABLE OF CONTENTS PAGE

1.0 SPECIFICATIONS................................................................................2

1.1 Technical Specifications.......................................................................2

1.2 Ordering Information ...........................................................................4

2.0 INTRODUCTION..................................................................................5

2.1 Inspecting the Package and Product.....................................................5

2.2 Product Description..............................................................................5

2.3 100Mb Fiber ports, SC Connectors.....................................................7

2.4 Frame Buffering and Latency...............................................................7

2.5 Features and Benefits ...........................................................................9

2.6 Applications .......................................................................................10

3.0 INSTALLATION.................................................................................11

3.1 Locating Magnum ITS Blade, 10/100Mb Hardened Switch..............11

3.2 Connecting Ethernet Media................................................................11

3.2.1 Connecting Twisted Pair (RJ-45, CAT 3 or CAT 5,)................11

3.2.2 Connecting Fiber Optic SC-type, "Snap-In" ..............................12

3.2.3 Connecting Fiber Optic ST-type, “Snap-In” (Optional).............13

3.2.4 Connecting

Single-Mode Fiber Optic ........................................13

3.2.5 Power Budget Calculations for ITS Blade Fiber Media.............13

3.2.6 Connections to NIC’s to support Auto -Negotiation, RJ-45 ......14

3.3 Powering the Magnum ITS Blade Switches.......................................14

4.0 OPERATION........................................................................................15

4.1 Dual-Speed Functionality, and Switching..........................................15

4.2 Auto-negotiation and Speed-sensing..................................................16

4.3 Auto-crossover feature on RJ-45 ports...............................................16

4.4 LED’s...............................................................................................17

5.0 TROUBLESHOOTING.......................................................................17

5.1 Before Calling for Assistance.............................................................17

5.2 When Calling for Assistance..............................................................18

5.3 Return Material Authorization (RMA) Procedure..............................19

5.4 Shipping and Packaging Information.................................................19

APPENDIX A: WARRANTY INFORMATION.........................................20

REV A 11/02: This revision is the initial release of the ITS Blade Hardened Switches for

Model 2070 Traffic Controller Chassis user manual.

www GarrettCom com

Magnum ITS Blade Hardened Switches for 2070’s Installation and User Guide (02/03)

1.0 SPECIFICATIONS

1.1 Technical Specifications

Ports Performance

Fiber, ports #1 and # 8, full duplex at 100Mbps

Copper (RJ-45) ports 2-7: auto-negotiating 10/100 Mbps,

MDI / MDIX auto-crossover is automatically handled

Network Standards

IEEE 802.1p QoS prioritization, 802.3u, 802.3x flow control

100Mb: Ethernet IEEE 802.3 100BASE-TX, 100BASE-FX

10 Mb: Ethernet IEEE 802.3, 10BASE-T

Packet-Processing

Filtering and Forwarding Rate from 100Mbps ports: 148,800 pps max

Filtering and Forwarding Rate from 10 Mbps ports: 14,880 pps max.

Processing type: Store and Forward, all ports non-blocking

Auto-learning: 4K-address table, shared for all ports

Packet buffers: 256 KB, dynamically shared

Latency (not including packet time): 100 to 10 Mbps: 5

10 to 100Mbps: 15

Path Delay Value: 50 BT on all ports

Maximum Ethernet Segment (or Domain) Lengths

10BASE-T (Unshielded twisted pair) - 100 m (328 ft)

100BASE-TX (CAT 5 UTP) - 100 m (328 ft)

100BASE-FX, full duplex: (multi-mode) - 2.0 km (6,562 ft)

100BASE-FX, full duplex: (single-mode) - 20.0 km (65,620 ft)

100BASE-FX, full duplex: (single-mode, long) - 40.0 km (131,240 ft)

Operating Environment

Ambient Temperature: 40°F to 167°F (-40°C to 75°C)

cold start down to 25°C

Storage Temperature: -40°to 185°F (-40°C to 85°C)

Ambient Relative Humidity: 5% to 95% (non-condensing)

Conformal coating applied as standard for humidity protection

Altitude: -200 to 15,000 ft. (-60 to 5,000m)

Operating Shock and Vibration: Designed to exceed CalTrans and ATC

requirements and Telcordia GR-63-CORE Sections 4.3.1 and 4.4.3

Power Supply (Internal

)

24VDC and -48VDC Power Supply

Power Input Voltage: 5VDC at 1.9Amps, 2070 backplane pins ABC29

per TEES 03/02

Power Consumption: 8 watts typical, 10 watts maxm.

www GarrettCom com

Magnum ITS Blade Hardened Switches for 2070’s Installation and User Guide (02/03)

Model 2070 Chassis Standards

Fits into slot A1 or A2, draws power from the Model 2070 chassis power

supply. Note- the ITS Blade is stand-alone for Ethernet operations; it

does not plug into any backplane signal pins

Network Cable Connectors -6 RJ-45 shielded female ports and 2-fiber port

100Mbps: Category 5 UTP/STP, fiber (50/125, 62.5/125 mm, or single-mode at

9/125 micron)

10 Mbps: Category 3, 4, 5 UTP (Note: auto-sensing does not sense cable type)

Mechanical

Dimensions: 8.70 in D x 1.6 in W x 7.0 in H

(220 mm x 40.4 mm x 177 mm)

Weight: 0.5 lb. (0.25 kg.)

LED Indicators

PWR: Steady ON when power applied

SPEED: (when LINK is ON): ON = 100Mbps; OFF = 10 Mbps

LINK/ACT: Steady ON for LINK with no traffic, blinking indicates port

is transmitting / receiving.

F/H (RJ-45 ports only): ON = full-duplex, OFF = half-duplex

MTBF (Bellcore method)

Over 25 years MTBF @ 60°C.

[email protected] for details

Agency Approvals

Emissions: meets FCC Part 15, Class A

Designed to meet TS-2 specifications

Warranty: Three years, return to factory Made in USA

www GarrettCom com

Magnum ITS Blade Hardened Switches for 2070’s Installation and User Guide (02/03)

1.2 Ordering Information

Magnum ITS Blade, 10/100 Ethernet Switch

with two 100Mb Fiber Port

TC62F-2MSC: Board-level Ethernet Switch for Model 2070 with six 10/100 RJ-

45 and two 100Mb FDX fiber multi-mode SC-type ports. HAVE 4K

address table and 256KB packet buffers. For use in slot A1 or A2 of

standard 2070 Controller chassis, which supplies power to Blade.

Ethernet cable connections are from the rear of the 2070 chassis.

Operates at -40°c to +75°C ambient temperature.

TC62F-1M1SSC: Same as TC62F-2MSC, except one 100Mb Ethernet fiber port is

20km single-mode SC.

TC62F-2SSC: Same as TC62F-2MSC, except both 100Mb Ethernet fiber port is

20km single-mode SC.

TC62F-NOF: Same as TC62F-2MSC, except no fiber ports (Has six 10/100 Ethernet

ports only.

TC62F-PS-TEST: Power supply for ITS Blade bench tests. Universal AC input,

mating TC62F DC jack plug.

Magnum ITS models with other fiber connector types and combinations available,

request quote for additional information.

GarrettCom, Inc. reserves the right to change specifications, performance

characteristics and / or model offerings without notice.

www GarrettCom com

Magnum ITS Blade Hardened Switches for 2070’s Installation and User Guide (02/03)

2.0 INTRODUCTION

2.1 Inspecting the Package and Product

Examine the shipping container for obvious damage prior to installing this product;

notify the carrier of any damage that you believe occurred during shipment or delivery. Inspect

the contents of this package for any signs of damage and ensure that the items listed below are

included.

This package should contain:

1 Magnum ITS Blade Ethernet Switch

1 Installation and User Guide (this manual)

1 Product Registration Card

Remove the Magnum ITS Blade from the shipping container. Be sure to keep the

shipping container should you need to ship the unit at a later date. To validate the product

warranty, please complete and return the enclosed Product Registration Card to GarrettCom, Inc.

as soon as possible.

In the event there are items missing or damaged, contact your supplier. If you need to

return the unit, use the original shipping container. Refer to Chapter 5, Troubleshooting, for

specific return procedures.

2.2 Product Description

The Magnum ITS Blade is Hardened 8-port Ethernet Switch in a board-level module

designed to fit into slot A1 or A2 of a standard 2070 Traffic Controller chassis. It allows

Ethernet media to quickly and easily be configured as the high bandwidth communications

protocol for the new generation of Intelligent Traffic Control systems.

www GarrettCom com

Magnum ITS Blade Hardened Switches for 2070’s Installation and User Guide (02/03)

The Magnum ITS Blade Ethernet Switch, equipped with six 10/100 RJ-45 ports and

two 100Mb Fiber ports, easily connects to local Ethernet devices at the intersection such as

video cameras and the Model 2070 Controller, while two Ethernet 100Mb fiber optic ports

connect upstream to the TOC or to intermediate Ethernet switches in the traffic control network.

The Magnum ITS Blade, entirely contained in a standard 2070 Traffic Control Chassis, draws its

power from the 2070 chassis power supply. Noo 2070 chassis backplane signal pins are used

The ITS Blade module easily can be fitted into either a new or existing 2070 chassis

without creating any conflict with other installed modules. The Magnum ITS Blade

specifications comply with Caltrans and NEMA TS-2-1998 Standards for Traffic Controller

Assemblies.

The two “future-proof” fiber ports have been designed as full-duplex 100Mbps

switched fiber ports. Six copper (RJ-45) with full / half-duplex-10/100-auto-negotiating ports

are included. The Magnum ITS Blade Hardened Switches provide the switching speed and the

reliability to smoothly support streaming Ethernet traffic at 100Mbps or 10Mbps speed. The

optional fiber ports are normally configured and tested with the ITS Blade in the factory, and are

available in multi-mode and single-mode SC-type fiber connectors.

Designed specifically to operate in Model 2070 Traffic chassis in temperature

uncontrolled road side boxes, the Magnum ITS Blade can easily sustain the heat…. and the cold.

Armored with unique thermal techniques (patent pending) developed by GarrettCom

technologists extend the ambient temperature operating range beyond standard product ratings,

www GarrettCom com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de GarrettCom

GarrettCom

GarrettCom Hubs Manual de usuario

GarrettCom

GarrettCom Magnum 8000X Manual de usuario

GarrettCom

GarrettCom Magnum 6K25e Manual de usuario

GarrettCom

GarrettCom DS8016 Manual de usuario

GarrettCom

GarrettCom MAGNUM H80B Manual de usuario

GarrettCom

GarrettCom Magnum 6KQ Manual de usuario

GarrettCom

GarrettCom Magnum 6K25 Manual de usuario

GarrettCom

GarrettCom Hardened Ethernet Switches P62F Manual de usuario

GarrettCom

GarrettCom 500-Series Manual de usuario

GarrettCom

GarrettCom Magnum 4K24F Manual de usuario

GarrettCom

GarrettCom Magnum 3000 Manual de usuario

GarrettCom

GarrettCom Magnum ES42 Series Manual de usuario

GarrettCom

GarrettCom PS14H-48VDC Manual de usuario

GarrettCom

GarrettCom Magnum 6KQ Manual de usuario

GarrettCom

GarrettCom MAGNUM 6KM Manual de usuario

GarrettCom

GarrettCom Ethernet Networks and Web Management Manual de usuario

GarrettCom

GarrettCom Magnum Quad-Series Manual de usuario

GarrettCom

GarrettCom Magnum 4K16 Manual de usuario

GarrettCom

GarrettCom Magnum 6KQE Manual de usuario

GarrettCom

GarrettCom 4K-Series Manual de usuario

GarrettCom

GarrettCom DS80C Manual de usuario

GarrettCom

GarrettCom Magnum 14E Manual de usuario

GarrettCom

GarrettCom Magnum 6K8-Series Manual de usuario

GarrettCom

GarrettCom Magnum DS80 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario