GAI-Tronics 727-001 Manual de usuario

Pub. 42004-690L2C

GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA

610-777-1374 800-492-1212 Fax: 610-796-5954

VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

GAI-TRONICS® CORPORATION

A HUBBELL COMPANY

Model 727-001

Desk Set Access Panel

Confidentiality Notice

This manual is provided solely as an operational, installation, and maintenance guide and contains sensitive

business and technical information that is confidential and proprietary to GAI-Tronics. GAI-Tronics

retains all intellectual property and other rights in or to the information contained herein, and such

information may only be used in connection with the operation of your GAI-Tronics product or system.

This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third party.

Introduction

The Model 727-001 Access Panel is a component of the SmartSeries ADVANCE system that can be used

for public address, intercommunication, and emergency notification.

How to Use the Assembly

Application

The Model 727-001 Desk Set Access Panel is used to communicate, initiate alarms and to control alarm

and paging destinations. It is equipped with a 120 V ac/240 V ac desktop power supply that allows the

access panel to be used in almost all installations without requiring additional line transformers.

The Model 727-001 Access Panel consists of the following main components:

27 configurable push buttons

A LAMP TEST push button

A total of 24 configurable LEDs available

Handset with pressbar

Speaker with volume control

Twenty-four of the 27 push buttons contain bi-color LED lamps that can be configured to provide system

status information.

The panel provides a handset equipped with an integral pressbar. The handset is used to make page

announcements and to hold two-way party line conversations. In addition, an internal speaker is provided

to allow page audio monitoring. The access panel also includes a volume control for the internal speaker.

NOTE:The speaker is disabled when the handset is in use.

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 2 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

The function of each of the 27 push buttons and 24 available LEDs is configurable using the GAI-Tronics

ADVANCE system software.

Hardware Configuration

Interfaces

A 3-conductor ac power cord is included with the access panel. One end of the power cord is connected

to the 3-prong connector located on the back of the power supply, while the other end is plugged into a

grounded ac electrical outlet.

The compatible ac input voltages are 120 V ac/240 V ac (auto-ranging), 50/60 Hz. The 5-pin DIN plug

from the power supply is connected to the 5-pin DIN jack on the rear of the access panel as shown in

Figure 3.

Figure 1. Model 727-001 Desk Set Access Panel

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 3 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

The data and audio connection to the system control unit is provided by an RJ-45 jack on the rear of the

access panel as shown in Figure 2. The following are the physical connections of the RJ-45 jack:

Pin Connection

1 No connection

2 No connection

3 No connection

4 No connection

5 −TX/RX connection

6 + TX/RX connection

7 No connection

8 No connection

The 5-pin XLR jack is used for connection of an optional desk mic as shown in Figure 3.

The DB-15 connector on the rear of the access panel is used for connecting the desk set to the optional

docking station. This connection allows the user to connect the power and the data/audio connection to

the rear of the docking station to ease overall installation of the docking station.

Figure 2.

Figure 3. Model 727-001 Access Panel Typical Connections (Rear View)

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 4 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

Installation

WARNING Please adhere to all warnings, safety, and operating instructions on the unit

and in the installation manual.

1. Disconnect power before servicing.

2. Avoid servicing the unit during electrical storms.

3. Do not touch uninsulated wires.

Mounting

Remove the access panel from its protective packing. Simply position the access panel on a sturdy

horizontal surface in a convenient location where the handset and push buttons are readily accessible.

Data Connection

Connect the RJ-11 data cable from the RJ-45 jack on the rear of the unit to the API connecting block

located in the ADVANCE control cabinet. If the 7-foot cable is not long enough, use a twisted-pair cable

terminated on one end with either an RJ-11 or RJ-45 plug. This connection is not polarity-sensitive and

may be wired in either orientation.

NOTE: This assembly includes a 7-foot RJ-11 data cable.

Power

Connect the 3-conductor ac power cord provided with the access panel as follows:

1. Plug one end of the power cord into the 3-prong power connector at the rear of the power supply.

2. Plug the 5-pin DIN connector of the power supply into the 5-pin DIN jack on the rear of the access

panel.

3. Plug the power supply cord into a grounded ac electrical outlet.

4. The access panel does not contain an integral power switch. The access panel will power up

immediately.

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 5 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

Label Creation

A Word 97 document is available to create custom slide-in labels for the desk set. It is available for

download at www.gai.tronics.com. Follow the SmartSeries link, and select Access Panels.

When you click on the document, you will be asked if you want to download the file; or if MS Word is

installed on your computer, it will open automatically. You may want to save the file on your computer

for future use.

Before printing on the included slide-in labels, print a test page on plain paper to verify that the

positioning, the orientation, and the information are correct. To check the printed paper, lay it behind the

included slide-in label sheet and verify that the print is in the proper location. Because printers vary, you

may need to adjust the margins in the page setup to center the printed text within the perforated strips.

To modify the text size and color of the text in the blocks, you will need to “unprotect” the document as

outlined below.

If you need to modify the margins you will need to perform the following steps:

1. Unprotect the document by selecting the Tools Menu, then clicking on Unprotect Document.

2. Next select File, then Page Setup.

3. Adjust the Top Margin and Left Margin value to move the printed text around on the sheet.

NOTE:Do not re-protect the document, otherwise all the information that was typed in will be lost.

After making any change to the slide-in label document, print a test copy on plain paper before using the

included slide-in label sheet.

To change the color of a cell or square:

1. Right click at the left edge of a cell to select the entire cell. The cell will reverse color.

2. Select Format, Borders and Shading, and then select the Shading tab.

3. Select a color from the chart by clicking on it; and be sure the “Applies to box” reads “cell” and then

click OK to apply.

The color will appear correctly when the cursor is moved to another location in the document.

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 6 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

Keypad Slide-In Labels

To install the keypad slide-in labels, proceed as

follows:

1. Separate the slide-in labels along the perforated

lines on the sheet.

2. Fold the tab at the end of the slide-in label so

that it is perpendicular to the reset of the label.

3. Slide the label into the appropriate slot opening

located at the top of each of the button columns.

4. Repeat the above steps for the remaining labels.

To replace the keypad slide-in labels, proceed as

follows:

1. Locate the tab at the top of the label and pull it

out from behind.

2. Slide label out using the tab that has been

exposed.

Button Layout and Default Configurations

For units to be used without a docking station, all buttons and 24 LEDs are available for use.

For units being used with a docking station:

ACK/NEXT button should be configured as button #26 and LED #20.

PREV button should be configured as button #27.

NOTE:LED #20 on the desk-set keypad will flash when the ACK/NEXT button on the docking station is

flashing, unless it is disabled.

Configurable Push Buttons

The 27 configurable push buttons can be configured for the following functions:

Initiating voice pages and alarms

Selecting zones

Routing voice pages and alarms

Selecting and resetting alarm and fault condition messages

Acknowledging system status

Selecting party lines

Activating relay groups

Figure 4. Button Layout

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 7 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

Operation

Operation of this assembly is highly dependent on the attached system’s software configuration. The

software is factory-created and subsequently downloaded to the system control unit via an external PC at

system start-up.

This access panel offers the standard features described below in addition to other configurable features.

The standard features include a handset used for page and party functions, and an integral speaker to

monitor page audio.

Handset Communications

The handset is used for both page and party communications. Lifting the handset from the cradle creates

an off-hook condition. In a normal configuration, lifting the handset causes it to be connected to a party

line.

Speaker and Speaker Muting

The access panel’s integral speaker provides the capability of monitoring system page activity. The

speaker’s volume can be adjusted using the volume adjustment knob.

NOTE:The speaker is disabled when the handset is in use.

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 8 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

How to Diagnose Assembly Faults

Servicing Guidelines

1. Notify plant personnel of a system shutdown prior to servicing the unit.

2. Disconnect power before connecting external wiring or installing or removing the access panel.

Symptom Action

Access panel does not function.

(No push buttons detected, no

LED lamps active, and handset is

not functioning.)

Verify ac power is applied to power supply. Verify that ac

power cord is plugged in. Also verify that ac outlet is active.

Verify that the LED is lit on top of the desktop power supply.

Call for service of the access panel.

LEDs are blinking and the

sounder is beeping

Verify that the data cable is properly connected between the access

panel and the control unit.

No configurable push buttons are

detected.

Verify that the data cable is properly connected between the

access panel and the control unit.

Call for service of the access panel.

Some configurable push buttons

are not detected.

Call for service of the access panel.

No LED lamps of any

configurable push buttons

activate.

Call for service of the access panel.

Some LED lamps of configurable

push buttons do not activate.

Call for service of the access panel.

Speaker does not function. Ensure that the speaker volume control is not turned down.

Call for service of the access panel.

Handset does not function

properly.

Call for service of the access panel.

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 9 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

Specifications

Electrical

Input voltage .................................................................................................................... 120 V ac/240 V ac

Auto-ranging

Input frequency ............................................................................................................................... 50/60 Hz

Input current draw (with lamp test depressed)................................................. 60 mA @ 120 V ac, nominal

200 mA @ 120 V ac, maximum

Environmental

Operating temperature range.................................................................. +32F to +120F (0C to +49C)

Relative humidity................................................................................................ Non-condensing 85% max.

Mechanical

Unit dimensions ........................................... 7.60 W 8.93 L 4.63 D inches (193.0 226.9 117.6 mm)

Unit weight.......................................................................................................................................... 4.6 lbs.

Handset material .......................................................................................................................... Black ABS

Handset microphone ........................................................................................................................ Dynamic

Handset receiver............................................................................................................................... Dynamic

Handset cord ....................................................................................... Hytrel, 6-foot (1.8 m) when extended

Handset cradle............................................................................................. Fixed, built-in off-hook detector

External controls ........................................................................................................... Press-to-page switch

27 configurable push buttons

Lamp test button

24 Bi-color LEDs

Speaker volume control

Pub. 42004-690L2C

Model 727-001 Desk Set Access Panel Page 10 of 10

f:\standard ioms - current release\42004 instr. manuals\42004-690l2c.doc

03/13

Optional Accessories

Model Number Description

12576-500 Desk Set Access Panel Docking Station with VFD

13610-002 Desk-top Access Panel Desk Mic

Replacement Parts

Model Number Description

14919-113 Keypad Replacement Slide-In Labels (set of 4)

51035-013 Replacement 28-Button Keypad

10119-001 Replacement Handset

61002-007 Replacement Line Cord

Reference Material

Reference to Assembly/Model Drawings

Published by Title GAI-Tronics Ref. No.

GAI-Tronics Model 727-001 Desk Set Access Panel Outline 73058

Tabla de contenidos

Otros manuales de Teléfono de GAI-Tronics

GAI-Tronics

GAI-Tronics 12576-502 Manual de usuario

GAI-Tronics

GAI-Tronics Titan Manual de usuario

GAI-Tronics

GAI-Tronics ITR1000-001 Manual de funcionamiento

GAI-Tronics

GAI-Tronics 256S Manual de usuario

GAI-Tronics

GAI-Tronics IDR1000A Manual de funcionamiento

GAI-Tronics

GAI-Tronics 226-002 Manual de usuario

GAI-Tronics

GAI-Tronics ITR1000A Manual de funcionamiento

GAI-Tronics

GAI-Tronics 227-005 Manual de usuario

GAI-Tronics

GAI-Tronics 295-001F Manual de usuario

GAI-Tronics

GAI-Tronics 276S Manual de usuario

GAI-Tronics

GAI-Tronics 352-101 Manual de usuario

GAI-Tronics

GAI-Tronics Auteldac 4 Manual de usuario

GAI-Tronics

GAI-Tronics Auteldac 5 Manual de usuario

GAI-Tronics

GAI-Tronics Titan Illuminated Crossing Telephone Manual de usuario

GAI-Tronics

GAI-Tronics Commander SMART Manual de usuario

GAI-Tronics

GAI-Tronics 7265-101 Manual de usuario

GAI-Tronics

GAI-Tronics IPE2500A Manual de funcionamiento

GAI-Tronics

GAI-Tronics 1090 Manual de usuario

GAI-Tronics

GAI-Tronics 262-001 Manual de usuario

GAI-Tronics

GAI-Tronics 263 Manual de usuario

GAI-Tronics

GAI-Tronics 210-001 Manual de usuario

GAI-Tronics

GAI-Tronics Titan GSM Manual de usuario

GAI-Tronics

GAI-Tronics ITR2000A Manual de funcionamiento

GAI-Tronics

GAI-Tronics PHP400 Manual de usuario

Manuales populares de Teléfono de otras marcas

GE 2-9480 Manual de usuario

Geemarc

Geemarc PHOTOPHONE 155 Manual de usuario

D-Link

D-Link DWR-720/PW Manual de usuario

Interquartz

Interquartz Gemini IQ333 Manual de usuario

SSS Siedle

SSS Siedle HT 840-0 Manual de usuario

Motorola

Motorola TITANIUM Manual de usuario

Panasonic

Panasonic ICX Manual de usuario

LG H870DS Manual de usuario

Samsung

Samsung GT-I9500 Manual de usuario

AT&T

AT&T Trimline 205 Manual de usuario

Selta

Selta zenyth 600 Manual de usuario

Doro

Doro AFTI 20 Manual de usuario

UNIQCELL

UNIQCELL A1 Manual de usuario

Panasonic

Panasonic KX Series Manual de usuario

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Manual de usuario

BT Decor 425 Manual de usuario

NEC

NEC SV8500 Manual de usuario

Teledex

Teledex PEARL Manual de usuario