Gabarron ECOSSH158 Instrucciones de montaje

INSTALLATION INSTRUCTIONS AND USER GUIDE

ECOMBI SSH

SMART STORAGE HEATER

ECOSSH158

ECOSSH208

ECOSSH308

ECOSSH408

Please, read these instructions CAREFULLY before installing or using this appliance for the first time.

1. –IMPORTANT INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock,

and injury to persons, including the following:

•WARNING: Please read all instructions before installing or using this heater for the first time.

•This heater is hot when in use. To avoid

burns, do not let bare skin touch hot

surfaces.

•Keep combustible materials, such as

furniture, pillows, bedding, papers, clothes,

etc. and curtains at least a foot (30cm) from

the front, sides and rear of the heater.

•It is essential that the indicated minimum

clearances are maintained.

•CAUTION —Some parts of this product

can become very hot and cause burns.

Particular attention must be given where

children and vulnerable people are present.

•Children should be supervised to ensure they do not play with the heater.

•Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left

operating unattended.

•This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance.

Cleaning and user maintenance must not be made by children without supervision.

•Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed

or installed in its intended normal operating position and they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years

shall not plug in, regulate and clean the appliance or perform user maintenance.

•Children of less than 3 years should be kept away unless continuously supervised.

•Do not operate any heater after it malfunctions. Disconnect power at service panel and have heater inspected by a

reputable electrician before reusing.

•Do not use the heater outdoors.

•To disconnect heater, turn controls to off, and turn off power to heater circuit at main disconnect panel.

•Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock

or fire, or damage the heater.

•To prevent a possible fire, do not block air intakes or exhaust in any manner.

•Air inlets and outlets provide proper operation of the appliance and prevent its overheating. DO NOT cover air inlet

and outlet grills.

•A heater has hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint, or flammable vapors or

liquids are used or stored.

•Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire,

electric shock, or injury to persons.

•This guide must be kept and given to any new user.

SAVE THESE INSTRUCTIONS

WARNING: In order to avoid overheating do not cover the heater.

2. - INSTALLATION INSTRUCTIONS

The symbols used in the text are explained below:

WARNING This indication shows the possibility of causing death from electric shock.

WARNING This indication shows the possibility of causing death or serious injury.

CAUTION This indication shows the possibility of causing injury or damage to properties only.

Symbol for useful information.

IMPORTANT: Wiring procedures and connections shall be in accordance with the national and local codes having jurisdiction.

•The warranty of the heater will not cover any damage caused by non observance of any of these instructions.

•The installation must be carried out in accordance with the current local electrical regulations. Any installation or

reinstallation has to be carried out by an experienced technician.

•Please check that the voltage in the rating label fits the power supply.

•This appliance must be grounded.

•The appliance should not be installed just below an electrical socket.

•The appliance must be installed in such a way that it is impossible for anyone using a bath or shower, to touch the

controls.

•If during any installation the thermal insulation shows any sign of damage, it must be replaced.

•This heater should be switched off at the circuit breaker before any repair work is carried out. This should also be done

during times of the year when heat is not required.

•This appliance is only for permanent connection to a fix installation. After installation a survey of the first charging cycle

should be carried out to ensure that the main input thermostat switches off. Ventilate the room during this first cycle.

•Never open a charged heater.

•To maintain stability, it is essential that the heater is placed on a level surface and care should be taken to avoid

irregular surfaces, such as may result from carpets or tiled surrounds partially protruding under the heater.

•The presence of air particles of smoke, dust and other pollutants could, in time, discolor the walls and surfaces around

the heater.

In order to achieve a correct installation of this device, follow these steps:

1. - Choose the right location to install ECOMBI SSH. The minimum clearances must be respected from the appliance to any

combustible material such as furniture or curtains. To reduce the risk of fire, do not store or use gasoline or other

flammable vapors and liquids in the vicinity of the heater.

2. - Open the carton at the indicated side and install the supporting feet without removing the heater.

Turn the carton upside down to allow the heater to stand on its feet and remove the carton. Check that it is the correct model

and that it is in good conditions.

Check that all parts have been delivered and are intact.

-1 Ecombi SSH heater casing.

-1 bag containing 2screws and 2dowels.

-2 supporting feet.

-This guide.

-1 superior fixing fitting.

-2 lateral fixing fitting.

The casing and storage bricks are supplied separately. Check the supplied bricks packages correspond to the ones

indicated on the heater carton.

The heater operation is not affected if bricks with minor damage are used.

3. - Take off the front panel by removing the two screws located at the bottom. Fix the lateral fittings to the metal structure by

using the appropriate screws.

4. - Place ECOMBI in your selected installation area. Use the heater fixing holes as a template and mark the wall through the

fixing holes with a pencil. Drill the required holes into the wall. Place the dowels and screws into the holes before the appliance

installation but do not fasten them tightly.

5. Attach ECOMBI to the dowels with the crews. IT MUST NOT BE HUNG ON THE SCREWS; these are used only to prevent

the device from overturning and not to support it. If there is any doubt concerning the wall strength, consult the corresponding

construction specialist. The appliances are heavy; it is the installer responsibility the correct installation and wall support of these

devices to prevent them from overturning.

6. - Connect the heater using the wiring diagram included at the end of this manual. Tighten properly the connection block

screws. Do not leave any remaining wire inside the heater.

WARNING Touching live connections can cause serious personal injury.

7. - Disconnect the aluminum heating element by removing the FAST-ON terminal on each end of the element.

WARNING Steel edges can cut.

Next unscrew the inner panel and remove it.

CAUTION In the interior part of this inner panel there is a very

delicate thermal insulation MICROTHERM panel. It has to be handled with

extreme care. AVOID TOUCHING IT.

8. Do not disconnect the electrical heating elements. Remove the packing cardboard. Lift and tilt the elements outwards being

careful not to damage the insulation on the bottom of the heater.

9. - Place the storage bricks carefully, with the flat side facing the back of the heater. Arrange two row levels of bricks.

10. Place the heating elements back into their original position. Place the other two rows of storage bricks with the flat side

facing out and always on the heating elements supporting tabs.

11. Replace the inner front panel. If the bricks have been fitted correctly you will have no difficulty in replacing the panel. Make

sure the bottom edge of the inner panel is inside the front lip of the heater. Please see below:

12. - Reconnect the two FAST-ON terminals to the aluminum heating element attached to the inner panel at both ends.

13. –When replacing the exterior front panel, align the 2 plastic upper pegs on the heater with the holes in the exterior panel.

Push the top up into place and push the bottom in until it rests on the plastic feet.

14. - Replace the front panel with screws.

RELOCATION

WARNING: Relocation to another location must be carried out by an experienced technician.

If during reinstallation the thermal insulation shows any sign of damage, it must be removed and replaced by an identical part.

MANUALLY RESET TEMPERATURE LIMITER

This heater employs a manually reset temperature limiter (see LR in the connection diagram).

This safety device operates when high temperatures are reached at the top of the heater. It requires re-setting manually:

Let the heater cool. The cause of overheating should be investigated.

WARNING: Re-setting manually must be carried out only by an experienced technician.

Turn off the heater at the circuit breaker.

Take off the front panel by removing the two screws located at the bottom. Find the limiter LR in the connection diagram and

push the small pin until a click is heard.

RIGHT

POSITION

WRONG

POSITION

3. - OPERATING INSTRUCTIONS

CAUTION: DO NOT USE THIS HEATER TO DRY CLOTHES. Do not cover this heater at any time.

CONNECTION / DISCONNECTION

Power switch.All models are equipped with a switch on the back

side panel. It is used to connect and disconnect ECOMBI SSH.

KEYBOARD:

ON/OFF

Once the heater is connected to a main supply you can turn the heater ON by switching the main ON/OFF switch positioned at

the rear right side of the heater as shown above.

BACKLIGHT

Pressing any button, the display will illuminate with a soft white colour. After certain time if no buttons are pressed the display

backlight will turn off.

Operating mode.

Button “+”

Press the key to increase

different values.

Button “-”

Press the key to decrease

different values.

“Config / Prog”Button

Press the button to programme

and configure the SSH storage

heater in AUTO Mode.

“OK” Button

Press the button to select

operation mode: Auto, Manual,

Off, and to set the value of the

different parameters.

G-Control Hub

connection indicator.

Heating on indicator.

Daily Programming:

Temperature level for each

time interval (1h) of the day.

Current set point

temperature in AUTO

mode.

Current Charge Level.

Open Windows Detection

indicator.

OPERATION MODES SELECTION

Press , the operation modes are displayed, with the selected one flashing.

Use or to select the desired operation mode. Confirm with .

The heater has three different operation modes: Auto, Manual override and

Standby Mode.

-Auto: The setpoint temperature varies according to the weekly

schedule setup in the unit. 3 different temperature levels (Comfort,

Moon and Frost Protection) can be selected for each time interval (1

hour) to adjust the temperature in the room to the habits and needs of

the different users.

-Manual Override: the storage heater will maintain the temperature

set point and will ignore the pre-set program.

-Standby Mode: the storage heater doesn't maintain any set

temperature or run any programs, keeping the time settings configured

previously.

AUTO MODE –Temperature Level

To modify the set temperatures within the program permanently, press and

release until the display shows the flashing temperature symbol .

Now press to select the temperature you want to change, COMFORT or

ECONOMIC. Use and to select the desired temperature.

You can temporary change the set temperature for the time period too. To do

this, increase or decrease the current temperature simply by pressing and

. Once the time period finishes, the temperature will revert back to the

programmed set temperature.

AUTO MODE –Programming & Time Setting

Programming

Enter programming:

Select temperature level:

Next 1 hour Time Interval:

Time Setting

PROGRAMMING

Press & Hold until the following is shown.

The first segment will start to flash. By pressing you can select whether you

want a Frost Protection setting (3°C), Moon setting (18°C) or Comfort

setting (21°C). Now press to move to the next 1hour time interval.

Once you've gone through all the time intervals for day 1, you will automatically

start on day 2 by pressing . Repeat the above steps until you go through all 7

days.

If you do not desire to modify the programming of a day within the week, press

to go through the next day.

SSH will not charge in Frost Protection time intervals.

TIME SETTING

After pressing when the last time interval for day 7 is flashing or after

pressing in day 7, the time setting configuration starts. The following is

shown with the day of the week flashing.

Use and to select today's date. 1=Monday, 2=Tuesday, Etc. and Press

to confirm.

Now the hours start to flash. Press and until you reach the correct time

(hour) and Press to confirm.

Now the minutes start to flash. Press and until you reach the correct

time (minutes) and Press to confirm.

If the device is associated with a G-Control Hub, the adjustment of time is

removed and the time in the G-Control Hub is configured in the heater automatically

If you do not desire to modify the time setting, press to exit. After setting

the time, the display will show and start to run the program and will flash

between the set temperature for the current day, time interval and the word

Pro to indicate the heater is running the set program.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Gabarron

Gabarron

Gabarron RX4P Instrucciones de montaje

Gabarron

Gabarron ADL 5030/14 Instrucciones de montaje

Gabarron

Gabarron IDM-2000 Instrucciones de montaje

Gabarron

Gabarron Elnur ECOMBI SSH Series Manual de usuario

Gabarron

Gabarron DILIGENS DIL4GC Instrucciones de montaje

Gabarron

Gabarron Elnur ECOMBI HHR Series Manual de usuario

Gabarron

Gabarron RF Series Instrucciones de montaje

Gabarron

Gabarron ECOMBI ECO158 Guía

Gabarron

Gabarron Elnur INGENIUM Series Diagrama de cableado

Gabarron

Gabarron RKS4Hi Manual de usuario

Gabarron

Gabarron Elnur INGENIUM RD4W Instrucciones de montaje

Gabarron

Gabarron TV-2002 Instrucciones de montaje

Gabarron

Gabarron IDP Series Instrucciones de montaje

Gabarron

Gabarron ADS 84 Instrucciones de montaje

Gabarron

Gabarron Elnur A-4 Instrucciones de montaje

Gabarron

Gabarron RF4P Instrucciones de montaje

Gabarron

Gabarron RF10E Plus Instrucciones de montaje

Gabarron

Gabarron SH6M Instrucciones de montaje

Gabarron

Gabarron PH-125 Plus Instrucciones de montaje

Gabarron

Gabarron Ecombi HHR Series Manual de usuario

Gabarron

Gabarron ECOMBI ECO158 Instrucciones de montaje

Gabarron

Gabarron IC-1200 Manual de usuario

Gabarron

Gabarron Elnur RBC11 Instrucciones de montaje

Gabarron

Gabarron RFS4P Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario