Furuno FR-1908V-BB Manual de usuario

www.furuno.com

ll brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Installation Manual

RIVER RADAR

FR-1908V-BB

SAFETY INSTRUCTIONS ................................................................................................ i

SYSTEM CONFIGURATION ........................................................................................... ii

EQUIPMENT LISTS........................................................................................................ iii

1. MOUNTING..............................................................................................................1-1

1.1 Antenna Unit ......................................................................................................................1-1

1.2 Processor Unit ...................................................................................................................1-5

1.3 Control Unit ........................................................................................................................1-7

1.4 Monitor Unit........................................................................................................................1-7

2. WIRING....................................................................................................................2-1

2.1 Antenna Unit ......................................................................................................................2-2

2.2 Processor Unit ...................................................................................................................2-6

3. ADJUSTMENTS ......................................................................................................3-1

3.1 How to Open the Protected Menus....................................................................................3-1

3.2 How to Set Alarms .............................................................................................................3-2

3.3 How to Enter Your Ship’s Characteristics ..........................................................................3-2

3.4 How to Adjust Sweep Timing .............................................................................................3-3

3.5 How to Adjust Video Level.................................................................................................3-4

3.6 Heading Alignment.............................................................................................................3-4

3.7 How to Suppress Main Bang .............................................................................................3-5

3.8 How to Set the Transmission Stop Area............................................................................3-6

3.9 How to Set the Radar Antenna Position ............................................................................3-6

3.10 How to Set the GPS Antenna Position...............................................................................3-6

3.11 How to Adjust the ROT/Rudder/Autopilot Graph (Analog Input Only) ...............................3-7

APPENDIX 1 JIS CABLE GUIDE .............................................................................AP-1

APPENDIX 2 INITIALIZE MENU TREE....................................................................AP-2

PACKING LISTS ......................................................................................................... A-1

OUTLINE DRAWINGS ................................................................................................ D-1

INTERCONNECTION DIAGRAM ................................................................................ S-1

SAFETY INSTRUCTIONS

Mandatory Action

Prohibitive Action

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not

avoided, could result in minor or moderate injury.

Warning, Caution

The installer of the equipment must read the safety instructions before attempting to

install the equipment.

Indicates a potentially hazardous situation which, if not

avoided, will result in death or serious injury.

Wear a safety belt and hard hat when working on the antenna unit.

Serious injury or death can result if someone falls from the radar

antenna mast.

WARNING

CAUTION

DANGER

Be sure that the power supply is

compatible with the voltage rating of

the equipment.

Fire or damage to the equipment can result

if a different cable is used.

Connection of an incorrect power supply

can cause fire or damage the equipment.

Use only the specified power cable.

Do not open the equipment

unless totally familiar with

electrical circuits and

service manual.

Only qualified personnel

should work inside the

equipment.

Construct a suitable service platform

from which to install the antenna unit.

Serious injury or death can result if some-

one falls from the radar antenna mast.

Turn off the power at the mains switch-

board before beginning the installation.

Fire, electrical shock or serious injury can

result if the power is left on or is applied

while the equipment is being installed.

ELECTRICAL

SHOCK

HAZARD

Observe the following compass safe

distances to prevent deviation of a

magnetic compass:

Antenna Unit

Standard

compass

1.35 m 0.85 m

Processor Unit 0.70 m 0.40 m

Steering

compass

Control Unit

0.60 m

0.35 m

Ground the equipment to

prevent electrical shock

and mutual interference.

Do not install the monitor unit, processor

unit or control unit where they may get

wet from rain or water splash.

Water in the units can result in fire,

electrical shock, or damage the equipment.

Use a disconnecting device (ex. breaker)

to connect this equipment to the mains

switchboard.

WARNING WARNING

CAUTION

SYSTEM CONFIGURATION

ANTENNA UNIT

Category of Units

Antenna Unit: Exposed to the weather

All other units: Protected from the weather

Radiator

XN20AF

XN24AF

24 VDC

Rectifier

RU-1746B-2

100/110/115/

220/230 VAC

1f, 50/60 Hz

RSB-120-102

(26 rpm)

PROCESSOR

UNIT

RPU-026

Sub Display

NMEA1 (HEADING SENSOR)

IEC61162-2

NMEA2 (AIS)

IEC61162-2

NMEA3 (NAV EQUIPMENT)

IEC61162-1

NMEA4 (Doppler)

IEC61162-1

NMEA5 (Alarm INS)

IEC61162-1

NMEA6 (ECDIS (TTM))

IEC61162-1

Control Unit

RCU-032

- ROT Sensor

(Analog/Alarm)

- Auto Pilot

(Analog/Follow-up)

- Rudder (Analog)

RW-0013

USB

DVI

RGB

24 VDC

External Monitor

(e.g. MU-190V)

External Monitor

or VDR

iii

EQUIPMENT LISTS

Standard Supply

Optional Supply

Name Type Code No. Qty Remarks

Antenna Unit XN20AF-RSB-120-102 - 12040 mm, 26 rpm

XN24AF-RSB-120-102 - 2550 mm, 26 rpm

Processor Unit RPU-026 - 1

Control Unit RCU-032 - 1

Installation Materials CP03-34401 001-194-530 1 For control unit

CP03-34501 001-194-550 1 For processor unit

CP03-33401 001-107-930 1 For antenna unit

CP03-19101 008-487-130 1 For radiator

Spare Parts SP03-17201 001-194-540 1 For processor unit

SP03-12501 008-485-360 1 For antenna unit

Name Type Code No. Qty Remarks

Rectifier RU-1746B-2 000-030-439 1

Cable Assy RNS-08-132 000-174-105 1 USB for LCD brilliance

EQUIPMENT LISTS

This page is intentionally left blank.

1-1

1. MOUNTING

1.1 Antenna Unit

1.1.1 Mounting considerations

• The antenna unit is generally installed either on top of the wheelhouse or on the ra-

dar mast, on a suitable platform. Locate the antenna unit in an elevated position to

permit maximum target visibility.

• No funnel, mast or derrick should be within the vertical beamwidth of the antenna in

the bow direction, especially zero degrees ±5°, to prevent blind sectors and false

echoes on the radar picture.

• It is rarely possible to place the antenna unit where a completely clear view in all

directions is available. Thus, you should determine the angular width and relative

bearing of any shadow sectors for their influence on the radar at the first opportunity

after fitting.

• Locate the antenna of a direction finder clear of the antenna unit to prevent interfer-

ence to the direction finder. A separation of more than two meters is recommended.

• To lessen the chance of picking up electrical interference, avoid where possible

routing the signal cable near other onboard electrical equipment. Also avoid running

the cable in parallel with a power cable.

• A magnetic compass will be affected if placed too close to the antenna unit. Observe

the compass safe distances shown on page ii to prevent deviation of a magnetic

compass.

• Do not paint the radiator aperture to ensure proper emission of the radar waves.

• The antenna base is made of cast aluminum. To prevent electrolytic corrosion of the

antenna base, use the seal washers and corrosion-proof rubber mat and ground the

unit with the ground wire (supplied).

• Deposits and fumes from a funnel or other exhaust vent can adversely affect the ae-

rial performance and hot gases may distort the radiator portion. The antenna unit

must not be mounted where the temperature is more than 55°C.

• Leave sufficient space around the unit for maintenance and servicing. See the an-

tenna unit outline drawing for recommended maintenance space.

Do not apply paint, anti-corrosive

sealant or contact spray to coating or

plastic parts of the equipment.

Those items contain organic solvents that

can damage coating and plastic parts,

especially plastic connectors.

NOTICE

1. MOUNTING

1-2

1.1.2 How to assemble the antenna unit

The antenna unit consists of the antenna radiator and the antenna unit chassis, and

they are packed separately. Fasten the antenna radiator to the antenna unit chassis

as below:

1. Attach two guide pins to the underside of the antenna radiator.

2. Remove a waveguide cap from the radiator bracket. The cap may be discarded.

3. Coat the waveguide flange with anticorrosive adheasive as shown below.

4. Coat fixing holes for the antenna radiator with anticorrosive adheasive.

5. Grease the O-ring and set it to the O-ring groove of the radiator flange.

6. Set the antenna radiator to the radiator bracket.

7. Coat hex bolts M8x40 with anticorrosive adheasive and use them to loosely fasten

the antenna radiator to the antenna unit chassis.

8. Remove two guide pins (inserted at step 1), and then tighten fixing bolts.

Hole for a

guide pin

5 mm Anticorrosive adheasive

Hole for a

guide pin

Waveguide cap

O-ring

10 mm

Be sure to remove the guide pins.

Injury may result if the guide pins loosen

and fall.

CAUTION

Antenna radiator

Waveguide

Radiator bracket

Hex bolt

(M8x40, 8 pcs.)

O-ring

Guide pin

1. MOUNTING

1-3

1.1.3 How to fasten the antenna unit to the mounting platform

The antenna unit may be assembled before hoisting it to the mounting platform. How-

ever, do not lift the antenna unit by the radiator. Always hold the unit by its housing.

When using a crane or hoist, use the hoist rings which should be fastened to the bolt

fixing covers of the antenna housing.

1. Construct a suitable mounting platform referring to the outline drawing at the end

of this manual.

2. Drill four mounting holes of 15 mm diameter and one cable entry hole of about 50

mm diameter in the mounting platform.

3. Lay the rubber mat (supplied) on the mounting platform.

4. Place the antenna unit on the rubber mat, orienting the unit so the bow mark on

its base faces the ship’s bow.

-To hoist antenna unit aboard vessel, attach ropes to lifting fixtures and

hoist unit with crane.

- To remove load from radiator when hoisting, the length of the rope

between the radiator base and the hook on the should be at least 130 cm.

- To keep the rope away from the radiator, turn the radiator and chassis

approx. 30 degrees as shown below.

- Be sure to remove the lifting fixtures after hoisting is completed.

130 cm

Hook

Lifting fixture

Approx.

30 deg.

Approx.

30 deg.

Lifting fixture

(Top view)

Hoist

rings

Hoist

rings

NO!

NOTICE

Ground

terminal

Rubber

mat

Bow mark

1. MOUNTING

1-4

5. Fasten the antenna unit to the mounting platform with M12x60 hex. bolts, nuts, flat

washers and seal washers.

6. Use hex. bolt (M6x25), nut (M6) and flat washers (M6) to establish the ground sys-

tem on the mounting platform as shown below. The location should be within 340

mm of the ground terminal on the antenna unit. Connect the ground wire

(RW-4747, 340 mm, supplied) between the grounding point and the ground termi-

nal on the antenna unit. Coat the entire ground system with adhesive (supplied).

7. Confirm that the hoist rings are removed.

The ground point must be within 300 mm from the ground termninal on

the antenna unit.

Coat with marine adheasive.

Antenna unit fixing bolt

(Sectional view)

Seal washer

Rubber mat

Mounting Platform

Anticorrosive adheasive

Flat washer

Spring washer

Hex. nut (Torque:

49 N•m

)

Antenna chassis

Ground wire

Anticorrosive adheasive

Ground wire

Anticorrosive

adheasive

Hex. bolt

Flat washer

Spring washer

Hex. nut

Mounting Platform

Flat washer

Hex. nut

Mounting Platform

Ground wire Hex. nut

Spring washer

Hex. bolt welded to ship’s superstructure

Otros manuales para FR-1908V-BB

Tabla de contenidos

Otros manuales de Radar de Furuno

Furuno

Furuno FAR2137S/12 Manual de usuario

Furuno

Furuno WR-2100 Manual de usuario

Furuno

Furuno FOIL-200 Manual de usuario

Furuno

Furuno DRS4A Manual de usuario

Furuno

Furuno FAR-3210 Manual de usuario

Furuno

Furuno FR-1908V-BB Manual de usuario

Furuno

Furuno DRS6A X-Class Manual de usuario

Furuno

Furuno FAR-3210 Manual de usuario

Furuno

Furuno FR-2105 Manual de usuario

Furuno

Furuno FAR-3230S-BB Manual de usuario

Furuno

Furuno FRS1000 Manual del operador

Furuno

Furuno FCR-1030 Manual de usuario

Furuno

Furuno WR2120 Manual de usuario

Furuno

Furuno WR2120 Manual de usuario

Furuno

Furuno FR-1500 MARK-3 Manual de usuario

Furuno

Furuno FAR-3220Z Manual de usuario

Furuno

Furuno DRS12AX X-Class Manual de usuario

Furuno

Furuno FR-1500 Manual de usuario

Furuno

Furuno DRS6A-NXT Manual de usuario

Furuno

Furuno WR-2100 Manual de usuario

Furuno

Furuno FCR-1010 Manual de usuario

Furuno

Furuno DRS6A Manual de usuario

Furuno

Furuno DRS4D-NXT Manual de usuario

Furuno

Furuno FAR-3320SW Manual de usuario

Manuales populares de Radar de otras marcas

SAW D2L

SAW D2L Valentine One Gen2 Manual de usuario

Raymarine

Raymarine Raytheon R20X Manual de usuario

Simrad

Simrad CA34 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR67B Especificaciones técnicas

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manual de usuario

ECHOMAX

ECHOMAX Active-X-Band Manual de usuario

AGD

AGD 340 Manual de usuario

Kustom Signals

Kustom Signals Eagle 3 Manual de usuario

SYMEO

SYMEO STU Manual de usuario

Axis

Axis D2110-VE Manual de usuario

MALA

MALA MIRA Manual de usuario

Emerson

Emerson ROSEMOUNT 5300 Manual de usuario

Rosemount

Rosemount 5300 Series Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex FMP56 Especificaciones técnicas

TERMA

TERMA SCANTER 5102 Manual de usuario

GSSI

GSSI UtilityScan Manual de usuario

Acconeer

Acconeer A111 Manual de usuario

Crosley

Crosley CR37 Manual de usuario