Furuno DRS6A Manual de usuario

www.furuno.com

ll brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Installation Manual

RADAR SENSOR

Model DRS6A X-Class

SAFETY INSTRUCTIONS ................................................................................................ i

SYSTEM CONFIGURATION .......................................................................................... iii

EQUIPMENT LISTS........................................................................................................ iv

1. INSTALLATION AND WIRING................................................................................... 1

1.1 Mounting Considerations ......................................................................................................1

1.2 Included Items.......................................................................................................................3

1.3 Required Tools and Materials...............................................................................................4

1.4 Fastening the Radiator to the Radiator Bracket....................................................................5

1.5 Mounting the Antenna Unit ...................................................................................................7

1.6 Wiring..................................................................................................................................10

2. INITIAL SETUP......................................................................................................... 13

2.1 Initial Setup for TZT9/TZT14/TZTBB ..................................................................................13

2.2 Initial Setup for TZTL12F/TZTL15F ....................................................................................16

3. MAINTENANCE, TROUBLE SHOOTING ................................................................ 18

3.1 Maintenance .......................................................................................................................19

3.2 Troubleshooting ..................................................................................................................19

3.3 Replacement of Fuse..........................................................................................................20

3.4 Life of Parts.........................................................................................................................20

SPECIFICATIONS ..................................................................................................... SP-1

OUTLINE DRAWING................................................................................................... D-1

INTERCONNECTION DIAGRAM ................................................................................ S-1

SAFETY INSTRUCTIONS

Mandatory Action

Prohibitive Action

WARNING

CAUTION

Warning, Caution

WARNING

The installer of the equipment must read the safety instructions before attempting to

install the equipment.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

can result in minor or moderate injury.

WARNING

Turn off the power at the

switchboard before beginning the

installation.

Fire or electrical shock can result if

the power is left on.

Do not open the equipment

unless you are well familiar with

electrical circuits.

Only qualified personnel should

work inside the equipment.

Be sure that the power supply is

compatible with the voltage rating

of the equipment.

Connection of an incorrect power

supply can cause fire or damage the

equipment.

Use only the specified power and

signal cable.

Fire or damage to the equipment

can result if a different cable is used.

Wear a safety belt and hard hat

when working on the antenna

unit.

Serious injury or death can result if

someone falls from the radar mast.

Do not disassemble or modify the

equipment.

Fire, electrical shock or serious

injury can result.

Construct a suitable service

platform from which to install the

antenna unit.

Serious injury or death can result if

someone falls from the radar mast.

Keep the objects away from the

antenna unit, so as not to impede

rotation of the antenna.

Fire, electrical shock or serious

injury can result.

Use the proper fuse.

Use of a wrong fuse can damage

the equipment or cause fire.

Do not depend one navigation

device for the navigation of the

vessel.

For the safety of vessel and crew,

the navigator must check all aids

available to confirm position.

SAFETY INSTRUCTIONS

Ground the equipment to prevent

mutual interference.

The radar antenna emits

electromagnetic radio frequency

(RF) energy which can be

harmful, particularly to your eyes.

Never look directly into the

antenna aperture from a close

distance while the radar is in

operation or expose yourself to

the transmitting antenna at a

close distance.

Distances at which RF radiation

levels of 100, 50 and 10 W/m2exist

are given in the table below.

WARNING LABEL

A warning label is attached to the antenna unit. Do not remove the label.

If the label is missing or damaged, contact your dealer about replacement.

Name: Warning Label (2)

Type: 03-129-1001-3

Code No: 100-236-743

It is recommended that you

connect the antenna unit to a

disconnecting device (circuit

breaker, etc.) to control the

power.

CAUTION

Observe the following compass safe

distances to prevent deviation of a

magnetic compass:

WARNING

0.1m

XN10A

3m0.5m

100 W/m250 W/m210 W/m2

Radiator

1.40 m

DRS6A X-Class

0.90 m

Model Standard

compass

Steering

compass

XN12A

XN13A

N/A 2.2m0.4m

N/A 1.9m0.2m

iii

SYSTEM CONFIGURATION

The DRS6A X-Class is compatible with the FURUNO Multi Function Displays shown below. The

combination with other models may not operate properly.

• NavNet TZtouch: TZT9, TZT14, TZTBB

• NavNet TZtouch2: TZTL12F, TZTL15F

: Standard supply

: Optional or local supply

Antenna Unit

RSB-134

Multi Function Display

NavNet TZtouch/Navnet TZtouch 2

Multi Function Display

NavNet TZtouch/Navnet TZtouch 2

24 VDC24 VDC

Ethernet HUB

HUB-101

EQUIPMENT LISTS

Standard supply

Optional supply

*: After the wiring, it is required to wind the vinyl tape around the LAN connector to waterproof.

Name Type Code No. Qty Remarks

Scanner Unit RSB-134 - 1

Radiator XN10A -

3.4 ft

XN12A - 4 ft

XN13A - 6 ft

Installation Materials TBD TBD 1 For scanner unit

TBD TBD 1 For radiator

CP03-36400 000-027-211

Power/LAN cable, 10 m

CP03-36410 000-027-212 Power/LAN cable, 15 m

CP03-36420 000-027-213 Power/LAN cable, 20 m

CP03-36430 000-027-214 Power/LAN cable, 30 m

Spare Parts TBD TBD 1 Fuse

Name Type Code No. Remarks

LAN Cable MOD-Z072-020+ 001-167-880-10 2 m

MOD-Z072-050+ 001-167-890-10 5 m

MOD-Z072-100+ 001-167-900-10 10 m

Joint Box TL-CAT-012 000-167-140-10 For LAN cable extension*

1. INSTALLATION AND WIRING

1.1 Mounting Considerations

Select a mounting location, keeping in mind in the following points:

• Install the antenna unit on the hardtop, radar arch or on a mast on an appropriate

platform.

• Locate the antenna unit where there is a good all-round view with, as far as possi-

ble, no part of the ship’s superstructure or rigging intercepting the scanning beam.

Any obstruction will cause shadow sectors and decrease the radiator’s performance

(beam width, side-lobe level, etc.). The loss of the radiator’s performance cause the

deterioration of the radar’s observation (bearing resolution, etc.) and false echoes.

A mast for instance, with a diameter considerably less than the horizontal beam

width of the radiator, will cause only a small shadow sector, but a horizontal spread-

er or cross trees in the same horizontal plane as the antenna unit would be a much

more serious obstruction; you would need to place the antenna unit well above or

below it. Be sure there are no metallic objects near the antenna.

• It is rarely possible to place the antenna unit where a completely clear view in all

directions is available. Thus, you should determine the angular width and relative

bearing of any shadow sectors for their influence on the radar at the first opportunity

after fitting.

NOTICE

Do not apply paint, anti-corrosive sealant or contact

spray to coating or plastic parts of the equipment.

Those items contain organic solvents that can damage

coating and plastic parts, especially plastic connectors.

(a) Common mast (b) Radar mast

Vertical beam angle = 22°

1. INSTALLATION AND WIRING

• In order to reduce the chance of picking up electrical interference, avoid where pos-

sible routing the power cable near other electrical equipment on-board. Also, avoid

running the cable in parallel with other power cables.

• It is not recommended to install the antenna unit on the hardtop of a cabin. Vibra-

tions from the antenna unit will pass through the hardtop and into the cabin.

• It is not recommended to install the antenna unit on the off-center position. The ra-

dar echoes on the display may not be aligned with the actual target’s bearing.

• Select a location that does not allow water to accumulate at the base of the antenna

unit.

• A magnetic compass will be affected if the antenna unit is too close to the compass.

Observe the compass safe distances mentioned in the SAFETY INSTRUCTIONS

to prevent interference to a magnetic compass.

• Do not paint the radiator to ensure proper emission of the radar waves.

• Make the maintenance space shown in the outline drawing for maintenance and

checking purpose.

• When this antenna unit is to be installed on a large vessel, consider the following

points:

• The supplied power/LAN cable runs between the antenna unit and display (or

ethernet HUB) and comes in lengths of 10 m, 15 m, 20 m or 30 m. Select the

length when purchasing.

• Deposits and fumes from a funnel or other exhaust vent can adversely affect the

aerial performance and hot gases may distort the radiator portion. The antenna

unit must not be mounted where the temperature is more than 55°C (131°F).

Not recommended

1. INSTALLATION AND WIRING

1.2 Included Items

•

Radiator* (1 pcs):

3.4 ft, 4 ft or 6 ft

•

Scanner Unit (1 pcs)

Radiator

• O-ring (1 pcs)

• Flat washer (M8, 4 pcs) • Spring washer (M8, 4 pcs)

• Hex. bolt (M8×30, 4 pcs)

• Silicone rubber (1 pcs)

Scanner Unit

• Stud bolt (M12×60, 4 pcs)

• Flat washer (M12, 4 pcs) • Spring washer (M12, 4 pcs)

• Hex nut (M12, 8 pcs) • Corrosion-proof rubber pad

(4 pcs)

• Spare fuse (1 pcs)

(5 A)

• Documents (1 set):

Mounting template is included.

Power/LAN cable

• Power/LAN cable* (1 pcs): 10 m, 15 m, 20 m or 30 m *: Select the length when purchasing.

1. INSTALLATION AND WIRING

1.3 Required Tools and Materials

Prepare the tools and materials shown below to install the antenna unit.

No. Name Remarks

1Electrical drill For making the mounting holes, drill bit: 15 mm

2Phillips-head screw driver #3, for fixing the cable cover

3Wrench For M10 (Hex. size 17 mm) and M12 (Hex. size 19 mm)

4Hex. L-wrench For fixing the stud bolts (Hex. size 6 mm)

5Self-vulcanizing tape For waterproofing the junction of connectors

6Vinyl tape

7Cable tie For fixing the cables

8 Ground wire IV-2sq

1. INSTALLATION AND WIRING

1.4 Fastening the Radiator to the Radiator Bracket

1. Remove the radiator cap from the radiator bracket.

2. Apply the silicone rubber to the surface of the radiator bracket as shown in the fig-

ure below.

3. Set the O-ring to the radiator bracket.

Radiator bracket

Radiator cap

Silicone rubber

Top view: Scanner unit

10 mm10 mm

: Silicone rubber application area

O-ring

Tabla de contenidos

Otros manuales de Radar de Furuno

Furuno

Furuno FOIL-200 Manual de usuario

Furuno

Furuno FR-1908V-BB Manual de usuario

Furuno

Furuno WR2120 Manual de usuario

Furuno

Furuno WR2120 Manual de usuario

Furuno

Furuno FCR-1010 Manual de usuario

Furuno

Furuno DRS4A Manual de usuario

Furuno

Furuno WR110 Manual de usuario

Furuno

Furuno DRS4D-NXT Manual de usuario

Furuno

Furuno FAR-3220Z Manual de usuario

Furuno

Furuno FAR-3320SW Manual de usuario

Furuno

Furuno FR-1500 MARK-3 Manual de usuario

Furuno

Furuno FAR2137S/12 Manual de usuario

Furuno

Furuno WR2120 Manual de usuario

Furuno

Furuno WR-2100 Manual de usuario

Furuno

Furuno FAR-3210 Manual de usuario

Furuno

Furuno WR-2100 Manual de usuario

Furuno

Furuno FAR-3230S-BB Manual de usuario

Furuno

Furuno FRS1000 Manual del operador

Furuno

Furuno DRS12AX X-Class Manual de usuario

Furuno

Furuno FAR-3210 Manual

Furuno

Furuno WR110 Manual de usuario

Furuno

Furuno FAR-3210 Manual de usuario

Furuno

Furuno DRS6A X-Class Manual de usuario

Furuno

Furuno DRS6A-NXT Manual de usuario

Manuales populares de Radar de otras marcas

SAW D2L

SAW D2L Valentine One Gen2 Manual de usuario

Raymarine

Raymarine Raytheon R20X Manual de usuario

Simrad

Simrad CA34 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR67B Especificaciones técnicas

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manual de usuario

ECHOMAX

ECHOMAX Active-X-Band Manual de usuario

AGD

AGD 340 Manual de usuario

Kustom Signals

Kustom Signals Eagle 3 Manual de usuario

SYMEO

SYMEO STU Manual de usuario

Axis

Axis D2110-VE Manual de usuario

MALA

MALA MIRA Manual de usuario

Emerson

Emerson ROSEMOUNT 5300 Manual de usuario

Rosemount

Rosemount 5300 Series Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex FMP56 Especificaciones técnicas

TERMA

TERMA SCANTER 5102 Manual de usuario

GSSI

GSSI UtilityScan Manual de usuario

Acconeer

Acconeer A111 Manual de usuario

Crosley

Crosley CR37 Manual de usuario