Fujitsu MAX3036RC SERIES Manual de usuario

C141-E237-01EN

MAX3147RC

MAX3073RC

MAX3036RC

HARD DISK DRIVES

PRODUCT/MAINTENANCE MANUAL

C141-E237

FOR SAFE OPERATION

Handling of This Manual

This manual contains important information for using this product. Read thoroughly before using the product.

Use this product only after thoroughly reading and understanding especially the section "Important Alert

Items" in this manual. Keep this manual handy, and keep it carefully.

FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to

their property. Use the product according to this manual.

IMPORTANT NOTE TO USERS

READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT. INCORRECT

USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE TO USERS, BYSTANDERS OR

PROPERTY.

While FUJITSU has sought to ensure the accuracy of all information in this manual, FUJITSU assumes no

liability to any party for any damage caused by any error or omission contained in this manual, its updates or

supplements, whether such errors or omissions result from negligence, accident, or any other cause. In

addition, FUJITSU assumes no liability with respect to the application or use of any product or system in

accordance with the descriptions or instructions contained herein; including any liability for incidental or

consequential damages arising therefrom.

FUJITSU DISCLAIMS ALL WARRANTIES REGARDING THE INFORMATION CONTAINED

HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY.

FUJITSU reserves the right to make changes to any products described herein without further notice and

without obligation.

This product is designed and manufactured for use in standard applications such as office work, personal

devices and household appliances. This product is not intended for special uses (atomic controls, aeronautic or

space systems, mass transport vehicle operating controls, medical devices for life support, or weapons firing

controls) where particularly high reliability requirements exist, where the pertinent levels of safety are not

guaranteed, or where a failure or operational error could threaten a life or cause a physical injury (hereafter

referred to as "mission-critical" use). Customers considering the use of these products for mission-critical

applications must have safety-assurance measures in place beforehand. Moreover, they are requested to

consult our sales representative before embarking on such specialized use.

The contents of this manual may be revised without prior notice.

The contents of this manual shall not be disclosed in any way or reproduced in any media without the express

written permission of Fujitsu Limited.

C141-E237

REVISION RECORD

Edition Date published Revised contents

01 July, 2005

Specification No.: C141-E237-**EN

C141-E237

Related Standards

Product specifications and functions described in this manual comply with the following ANSI (*1)

standards.

Document number Title

T10/1236D Rev.20

[NCITS.351:2001] SCSI Primary Commands-2 (SPC-2)

T10/996D Rev. 8c

[NCITS.306:1998] SCSI-3 Block Commands (SBC)

T10/1157D Rev. 24 SCSI Architecture Model-2 (SAM-2)

T10/1561D Rev. 14 SCSI Architecture Model-3 (SAM-3)

T10/1562D Rev. 05 Serial Attached SCSI (SAS)

T10/1601D Rev. 07 Serial Attached SCSI Model-1.1 (SAS 1.1)

*1 ANSI = American National Standard Institute

In case of conflict between this manual and any referenced document, this manual takes precedence.

C141-E237 i

Preface

This manual describes MAX3147RC, MAX3073RC, and MAX3036RC 3.5" type hard

disk drives with an embedded Serial Attached SCSI (SAS).

This manual details the specifications and functions of the above disk drive, and gives the

requirements and procedures for installing it into a host computer system.

This manual is written for users who have a basic understanding of hard disk drives and

their use in computer systems. The MANUAL ORGANIZATION section describes

organization and scope of this manual. The need arises, use the other manuals.

The organization of this manual, related reference manual and conventions for alert

messages follow.

Overview of Manual

This manual consists of the following seven chapters:

Chapter 1 General Description

This chapter introduces the disk drives standard features, hardware, and system

configuration.

Chapter 2 Specifications

This chapter gives detailed specifications of the disk drives and their installation

environment.

Chapter 3 Data Format

This chapter describes the data structure of the disk, the address method, and what to do

about media defects.

Chapter 4 Installation Requirements

This chapter describes the basic physical and electrical requirements for installing the disk

drives.

Chapter 5 Installation

This chapter explains how to install the disk drives. It includes the notice and procedures

for setting device number and operation modes, mounting the disk drive, and confirming

drive operation.

Chapter 6 Diagnostics and Maintenance

This chapter describes the automatic diagnosis, and maintenance of the disk drive. This

chapter also describes diagnostic methods for operation check and the basics of

troubleshooting the disk drives.

Chapter 7 Error Analysis

This chapter describes in details how collect the information for error analysis and how

analyze collected error information.

Preface

ii C141-E237

CONVENTIONS USED IN THIS MANUAL

MAX3147RC, MAX3073RC, and MAX3036RC disk drives are described as "the hard

disk drives (HDD)", "the disk drive" or "the device" in this manual.

Decimal number is represented normally.

Hexadecimal number is represented as X'17B9', 17B9h or 17B9H.

Binary number is represented as "010".

Conventions for Alert Messages

This manual uses the following conventions to show the alert messages. An alert message

consists of an alert signal and alert statements. The alert signal consists of an alert symbol

and a signal word or just a signal word.

The following are the alert signals and their meanings:

This indicates a hazardous situation could result in minor

or moderate personal injury if the user does not perform

the procedure correctly. This alert signal also indicates

that damages to the product or other property, may occur if

the user does not perform the product correctly.

This indicates information that could help the user use the

product more efficiently.

In the text, the alert signal is centered, followed below by the indented message. A wider

line space precedes and follows the alert message to show where the alert message begins

and ends. The following is an example:

(Example)

Damage

Never open the disk enclosure for any reason. Doing so will void any

warranties.

The main alert messages in the text are also listed in the “Important Alert Items.”

Attention

Please forward any comments you may have regarding this manual.

To make this manual easier for users to understand, opinions from readers are needed.

Please write your opinions or requests on the Comment at the back of this manual and

forward it to the address described in the sheet.

C141-E237 iii

Important Alert Items

Important Alert Messages

The important alert messages in this manual are as follows:

A hazardous situation could result in minor or moderate personal injury if the

user does not perform the procedure correctly. Also, damage to the product

or other property, may occur if the user does not perform the procedure

correctly.

Task Alert message Page

Installation

Damage

Never remove any labels from the drive or deface them in any way.

4-3

High temperature

To prevent injury, never touch the drive while it is hot. The DE and LSI

become hot during operation and remain hot immediately after turning off

the power.

5-1, 5-10

Damage

1. When dismounting the drive which is mounted on the

system while power is supplied to it.

• The spindle motor can be stopped by a START/STOP command. It

takes about 30 seconds for the spindle motor to stop completely.

• Then, dismount the drive using the drive mounting/dismounting

mechanism, etc. of the system. If the drive is dismounted while the

spindle motor is running, special care is required to avoid excessive

vibration or shock to the drive. Just in case, stop dismounting once

when SAS connector breaks off contact and wait until the spindle

motor stops (about 30 seconds.).

• When storing or transporting the drive, put it in the antistatic bag

(refer to Section 5.1).

5-10

Important Alert Items

iv C141-E237

Task Alert message Page

Installation 2. When dismounting the drive which is mounted on the

system while power is not supplied to it.

• Dismount the drive using the drive mounting/dismounting mechanism,

etc. of the system.

• When storing or transporting the drive, put it in the antistatic bag

(refer to Section 5.1).

5-10

Diagnostics

and

Maintenance

Data loss

Save data stored on the disk drive to other media before requesting repair.

Fujitsu does not assume responsibility if data is destroyed during servicing

or repair.

6-5

Electrical shock

Never touch the HDDs while power-feeding.

6-5

Damage

1. Always ground yourself with a wrist strap connected to ground before

handling. ESD (Electrostatics Discharge) may cause the damage to the

device.

2. Never use a conductive cleaner to clean the HDDs.

3. Never remove any labels from the drive or deface them in any way.

4. Never remove the PCA.

5. Never open the disk enclosure for any reason.

6-5

Damage

1. Never remove any labels from the drive.

2. Never open the disk enclosure for any reason. Doing so will void any

warranties.

6-13

C141-E237 v

MANUAL ORGANIZATION

PRODUCT/

MAINTENANCE MANUAL

(This manual)

1. General Description

2. Specifications

3. Data Format

4. Installation Requirements

5. Installation

6. Diagnostics and Maintenance

7. Error Analysis

INTERFACE

SPECIFICATIONS

1. Interface

2. Command Processing

3. Data Buffer Management

4. Command Specifications

5. Sense Data and Error Recovery Methods

6. Disk Media Management

This page is intentionally left blank.

Otros manuales para MAX3036RC SERIES

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Fujitsu

Fujitsu

Fujitsu PG-HDH61D Manual de usuario

Fujitsu

Fujitsu MAU3036NC/NP Manual de usuario

Fujitsu

Fujitsu PRIMERGY SX960 S1 Manual de usuario

Fujitsu

Fujitsu MPC3096AT - Desktop 9.7 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu MHU2100AT Manual de usuario

Fujitsu

Fujitsu GP5-HDH8B Manual de usuario

Fujitsu

Fujitsu MBA3300 NP SERIES Manual de usuario

Fujitsu

Fujitsu MHV2080AS - Extended Duty Mobile 80 GB Hard... Manual de usuario

Fujitsu

Fujitsu MHR2010AT Manual de usuario

Fujitsu

Fujitsu ETERNUS DX Disk Manual de usuario

Fujitsu

Fujitsu PRIMERGY LTO3 Manual de usuario

Fujitsu

Fujitsu MAG3182FC SERIES Manual de usuario

Fujitsu

Fujitsu MAV2036RC - 36.7 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu ETERNUS CS800 Manual de usuario

Fujitsu

Fujitsu GRANPOWER 5000 GP5-HDH451 Manual de usuario

Fujitsu

Fujitsu MAT3300NC Manual de usuario

Fujitsu

Fujitsu ETERNUS DX80 Manual de usuario

Fujitsu

Fujitsu MPC3032AT Manual de usuario

Fujitsu

Fujitsu PG-HD2E4H Manual de usuario

Fujitsu

Fujitsu ETERNUS DX S5 Series Guía

Fujitsu

Fujitsu MHT2080AH - 80GB 5400 RPM PATA Hard Drive Manual de usuario

Fujitsu

Fujitsu ETERNUS DX60 Manual de usuario

Fujitsu

Fujitsu ETERNUS DX Disk Manual de usuario

Fujitsu

Fujitsu MHV2040BH Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario