Fujitsu M3093DE Guía de referencia

Fujitsu Video Scanner Installation Procedures

Windows 98SE\ME\2000\XP

Rev051806A Page 1 of 3

If you are installing the following models by means of the Video interface then use this

document.

M3093E M3096E M3097DE M3099EH

M3093EX M3096EX M3099A M4097D

M3093DE M3097E+ M3099EX M4099D

Hardware requirements.

You will need a PC system that meets our recommended specifications, an appropriate video

controller (Kofax 850/1700V series), and a “Y” cable. For recommended PC system

specifications and Video controllers please reference the Scanner Hardware Reference page.

You may also need your Operating System Disk.

Step A: Installing the Serial-Video driver.

1. First boot your PC and install the driver that shipped with the controller card or

download the driver from the controller manufacturer’s Web page. Special note: If

you are installing a Kofax driver and any other software that contains Kofax’s Image

Controls pay close attention to the individual runtimes. It is strongly recommended

that you install the oldest/lower runtime first.

Step B: Installing the Serial-Video controller.

2. Shut down your PC and remove the case cover.

3. Locate a free PCI slot and remove the back plate if necessary.

4. Install the SCSI controller in an open PCI slot. Make sure that the card is seated

completely in the slot and secured in the frame.

Warning! Failure to secure the controller in the PC can result in damage to the

controller, scanner, and/or your system.

5. Boot your PC without the scanner attached and check for errors. If no errors then

proceed to the next step.

Step C: Unlocking the shipping lock.

If your model scanner does not have a flatbed then proceed to Step F.

The flatbed model scanners typically include a lock on the flatbed designed to protect

the scanner during shipment. Before the scanner can be used the shipping lock must be

unlocked. To unlock it do the following:

1. Located the shipping lock slider tab or knob underneath the end of the scanner.

2. Slide or rotate the lock to the unlock position.

Fujitsu Video Scanner Installation Procedures

Windows 98SE\ME\2000\XP

Rev051806A Page 2 of 3

If your model has the old style “L” bracket shipping lock.

3. Slide the scanner to its side as shown in figure below.

4. Unscrew the retainer screw and remove the shipping bracket.

5. Place the shipping bracket in the “use position” slot and secure it with the retainer

screw (see figure below)

6. Place scanner back in its normal position

Special note: The M3099A\EX\EH and M4099D do not have a shipping lock.

Step D: Connecting the Scanner.

Warning! Before proceeding ensure that the power is off when connecting or disconnecting the

SCSI cable to the scanner or workstation. Failure to follow the procedure above could result in

damage to the Video card, scanner, and/or your system.

Connect the tail of the “Y” which has the largest connector to the port on the controller

that you installed in the PC. Next connect the RS-232(serial) connector to the RS-232

port on the scanner. Lastly connect the remaining connector (video) to the video port of

the scanner and ensure that all connections are securely fastened.

Fujitsu Video Scanner Installation Procedures

Windows 98SE\ME\2000\XP

Rev051806A Page 3 of 3

Finally connect the power cord to the scanner and a wall outlet then turn on the scanner.

For those models without a power switch plug in the power supply to the back of the

scanner. To establish communication between the Scanner and your PC system turn on

the scanner prior to turning on your system. The scanner power and LED/LCD display

will light up. Next after the scanner completes its startup initialization the LED/LCD will

display either ready or the number one. This indicates that the scanner is ready.

Special note: On video scanners the ready light will not come on.

Step E: Configuring the scanner driver.

1. Go to Start, Settings, Control Panel, and double click on KSM (Kofax Source

Manager).

2. Click on Next then click on Create and type in a source name (typically the scanner

model).

3. Click on the drop down menu and select Adrenaline in the Source type and click

O.K. On the next screen Select your model scanner on the list and click O.K. to

finish.

Step F: Scanning with VCDEMO32P.

1. Go to Start, Programs, Kofax VRS or Kofax Image Controls, and select

VCDEMO32P.EXE.

2. Next go to Source, Scanner, and click on the drop down arrow; then select the

source that you created in the KSM. Wait a couple of seconds for the Kofax engine

to load, and then place your documents in the scanner.

3. Now go to Source, Properties and select your scanning parameters (i.e. scan

source - Flatbed or ADF, resolution, paper size).

4. Afterwards go to Source, and click on Process Image for single page scans or

Process Batch for multi-page batch scans.

Congratulations! You have successfully completed and tested your scanner installation.

*If you do not have any unzipping software installed on your system, you can download a free

evaluation copy at www.winzip.com.

Otros manuales para M3093DE

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escáner de Fujitsu

Fujitsu

Fujitsu fi-60F Manual de usuario

Fujitsu

Fujitsu FI-4010CU Manual de usuario

Fujitsu

Fujitsu PA03360-B615 Manual

Fujitsu

Fujitsu FI-5530C2 Guía de configuración

Fujitsu

Fujitsu S500M - ScanSnap - Document Scanner Manual de usuario

Fujitsu

Fujitsu fi-6140Z Manual de usuario

Fujitsu

Fujitsu M3093E Manual

Fujitsu

Fujitsu ScanSnap fi-5110C Manual de usuario

Fujitsu

Fujitsu FI-6000NS Manual

Fujitsu

Fujitsu TWAIN 32 Manual de usuario

Fujitsu

Fujitsu fi-590PRB Manual

Fujitsu

Fujitsu fi-6240C Guía de configuración

Fujitsu

Fujitsu ScanSnap iX1600 Instrucciones de montaje

Fujitsu

Fujitsu SP-1120 Guía de configuración

Fujitsu

Fujitsu fi-4530C Manual

Fujitsu

Fujitsu ScanSnap N1800 Guía de inicio rápido

Fujitsu

Fujitsu S510M - ScanSnap - Document Scanner Guía de configuración

Fujitsu

Fujitsu FI-4990C Manual de usuario

Fujitsu

Fujitsu Fujitsu fi-5950 Manual

Fujitsu

Fujitsu fi-7160 Manual de usuario

Fujitsu

Fujitsu fi-4750L Manual del instalador

Fujitsu

Fujitsu fi-65F Manual de usuario

Fujitsu

Fujitsu ScanSnap S1100i Instrucciones de montaje

Fujitsu

Fujitsu fi-4640S Manual de usuario

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario

Innova

Innova 5210 Manual de usuario

Visioneer

Visioneer CardReader 100 Guía de inicio rápido

Rohde & Schwarz

Rohde & Schwarz TSME6 Manual de usuario