Fujitsu MS-6178MICROATX WH5 Manual de usuario

User manual

Mainboard MS-6178MICROATX WH5

Version 1.0C

Manual Rev: 1.0B

Release Date: June 1999

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a

class B digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference, in which case the

user will be required to correct the interference at his own expense.

Notice 1

The changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order

to comply with the emission limits.

VOIR LA NOTICE D'INSTALLATION AVANT DE RACCORDER

AU RESEAU.

Micro-Star International MS-6178

For Home or Office Use

Tested to comply

with FCC Standard

iii

Edition

June 1999

The material in this document is the intellectual property of PREMIO®.

We take every care in the preparation of this document, but no guarantee

is given as to the correctness of its contents. Our products are under

continual improvement and we reserve the right to make changes without

notice.

Trademarks

All trademarks used in this manual are the property of their respective

owners.

Intel and Pentium are registered trademarks of Intel Corporation.

PS/2 and OS/2 are registered trademarks of IBM Corporation.

Windows 95 and Windows NT are registered trademarks of Microsoft.

Netware is a registered trademark of Novell.

Award is a registered trademark of Award Software Inc.

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Safety Instructions

1. Always read the safety instructions carefully.

2. Keep this User’s Manual for future reference.

3. Keep this equipment away from humidity.

4. Lay this equipment on a reliable flat surface before setting it up.

5. The openings on the enclosure are for air convection hence protects the

equipment from overheating. DO NOT COVER THE OPENINGS.

6. Make sure the voltage of the power source and adjust properly

110/220V before connecting the equipment to the power inlet.

7. Place the power cord such a way that people can not step on it. Do not

place anything over the power cord.

8. Always Unplug the Power Cord before Inserting any add-on card or

module.

9. All cautions and warnings on the equipment should be noted.

10. Never pour any liquid into the opening that could damage or cause

electrical shock.

11. If any of the following situations arises, get the equipment checked by a

service personnel:

•The power cord or plug is damaged

•Liquid has penetrated into the equipment

•The equipment has been exposed to moisture

•The equipment has not work well or you can not get it work

according to User’s Manual.

•The equipment has dropped and damaged

•If the equipment has obvious sign of breakage

12. DO NOT LEAVE THIS EQUIPMENT IN AN EVIRONMENT

UNCONDITIONED, STORAGE TEMPERATURE ABOVE 600 C

(1400F), IT MAY DAMAGE THE EQUIPMENT.

Table of Contents

Chapter 1: Introduction 1-1

Mainboard Features --------------------------------------------------- 1-2

Mainboard Layout----------------------------------------------------- 1-5

Chapter 2: Hardware Installation 2-1

Central Processing Unit: CPU--------------------------------------- 2-1

CPU Installation Procedures------------------------------------ 2-1

CPU Core Speed Derivation Procedure----------------------- 2-2

Overclocking Jumper : J25------------------------------------ 2-2

Fan Power Connector: CPUFAN------------------------------ 2-3

Clear CMOS Jumper: JBAT1/J26---------------------------------- 2-4

Memory Installation--------------------------------------------------- 2-5

Memory Bank Configuration----------------------------------- 2-5

Memory Installation Procedures-------------------------------- 2-6

Memory Population Rules--------------------------------------- 2-7

Case Connector : JFP1----------------------------------------------- 2-8

Floppy Disk Connector: FDD-------------------------------------- 2-10

Hard Disk Connectors: IDE1 & IDE2------------------------------ 2-11

Power Supply----------------------------------------------------------- 2-12

ATX 20-pin Power Connector: JPWR1---------------------- 2-12

IrDA Infrared Module Connector: J9------------------------------ 2-13

Serial Port Connectors: COM A & COM B ---------------------- 2-14

Parallel Port Connector: LPT1-------------------------------------- 2-15

Mouse and Keyboard Connector: JKBMS1---------------------- 2-16

Joystick/Midi Connectors-------------------------------------------- 2-17

Audio Port Connectors----------------------------------------------- 2-17

USB Connectors------------------------------------------------------- 2-18

Power Saving Switch Connector: JGS1----------------------------- 2-19

Power Saving LED Connector: JGL1------------------------------ 2-20

Wake-Up on LAN Connector: JWOL1----------------------------- 2-21

Modem Wake Up Connector: JMDM1---------------------------- 2-22

Modem-In: J6-------------------------------------------------------- 2-23

AUX Line In Connector: J5----------------------------------------- 2-24

CD-In Connector: J8------------------------------------------------- 2-25

Keyboard Power: JKBV1------------------------------------------- 2-26

Chassis Intrusion Switch Case: J10(optional)--------------------- 2-27

BIOS Flash Jumper: JP3--------------------------------------------- 2-28

Onboard Audio Enabled/Disabled Jumper: JP4------------------ 2-29

vii

Case Speaker to Audio Speaker Jumper: J15--------------------- 2-30

SPDIF Connector: J22(optional) ---------------------------------- 2-31

AMR (Audio Modem Riser)----------------------------------------- 2-32

PTI (PanelLink TV-Out Interface)---------------------------------- 2-33

Chapter 3 Award®BIOS SETUP 3-1

Entering Setup---------------------------------------------------------- 3-2

Getting Help------------------------------------------------------------ 3-2

The Main Menu------------------------------------------------------- 3-3

Standard CMOS Setup----------------------------------------------- 3-5

Advanced BIOS Features-------------------------------------------- 3-8

Advanced Chipset Features------------------------------------------ 3-12

Integrated Peripherals------------------------------------------------ 3-15

Power Management Setup------------------------------------------- 3-20

PnP/PCI Configuration Setup--------------------------------------- 3-24

PC Health Status (optional)------------------------------------------ 3-26

Frequency/Voltage Control------------------------------------------ 3-28

Load Fail-Safe/Optimized Defaults--------------------------------- 3-29

Set Supervisor/User Password--------------------------------------- 3-30

Chapter 4 Intel 810 Integrated Graphics Controller 4-1

Overview--------------------------------------------------------------- 4-1

Intel 810 VGA Driver Setup & Usage Procedures--------- 4-3

Chapter 5 ICH AUDIO DRIVER 5-1

Overview--------------------------------------------------------------- 5-1

Audio Driver Setup & Usage Procedures---------------------- 5-2

CHAPTER 1INTRODUCTION

1-1

TheMS-6178MICROATXWH5mainboardis ahigh-performancecomputer

mainboard based on Intel®810 chipset. The MS-6178 is designed for the

Intel®CeleronTM (PPGA) processor for inexpensive business/personal

desktop markets.

The Intel®810 chipset is the first generation Integrated Graphics chipset for

the Intel®CeleronTM processor. The graphics accelerator architecture

consists of dedicated multi-media engines executing in parallel to deliver

high performance 3D, 2D, and motion compensation video capabilities. An

integrated centralized memory arbiter allocates memory bandwidth to

multiple system agents to optimize system memory utilization. A new

chipset component interconnect, the hub interface, is designed into the Intel

810 chipset to provide an efficient communication channel between the

memory controller hub and I/O hub controller.

The Intel®810 chipset contains three core components: the Graphics and

MemoryController Hub (GMCH),theI/O Controller Hub(ICH0)

andthe Firmware Hub (FWH). The GMCH integrates a 66/100MHz, P6

family system bus controller, integrates 2D/3D graphics accelerator, 100MHz

SDRAM controller and high-speed hub interface for communication with the

ICH0/ICH. TheICH0 integrates an UltraATA/33(ICH0),USB host controller,

LPC interface controller,FWHinterface controller, PCI interfacecontroller,

AC’97digital controllerand ahubinterface for communication with theGMCH.

The Intel®82802 Firmware Hub (FWH) component is part of the Intel®810

chipset. The FWH is key to enabling future security and manageability

infrastructure for the PC platform.

Chapter 1

INTRODUCTION

CHAPTER 1INTRODUCTION

1-2

1.1 Mainboard Features

CPU

lSupport Socket370 for Intel®CeleronTM processor.

lSupport300MHz,333MHz, 366MHz,400MHz, 433MHz,466Mhz,500MHz orhigher

Chipset

lIntel®810(GMCH)chipset. (421BGA)

- Integrated Graphics Controller

- Intel DDM Architecture

- SDRAM memory Independent of System Bus

- Support 4MB Display Cache (only for GMCH)

lIntel®ICH0chipset. (241BGA)

- AC’97 Controller Integrated

- 2 full IDE channels

-LowpincountinterfaceforSIO

FrontSide Bus (FSB)

l66/100MHzclocks are supported.

MainMemory

lSupport two 168-pin DIMM sockets.

lSupporta maximum memory size of256MB(64Mbittechnology) or

512MB(128Mbittechnology) SDRAM.

Slots

lOne AMR (Audio Modem Riser) and one PTI (PanelLink TV-Out Inter-

face).

lThree 32-bit Master PCI Bus slots.

lSupport 3.3v/5v PCI bus Interface.

On-BoardIDE

lAnIDEcontrolleron the ICH/ICH0 chipset provides IDE HDD/CD-ROM

with PIO, Bus Master, Ultra DMA/33 .

lCan connect up to four IDE devices.

Tabla de contenidos

Otros manuales de Placa madre de Fujitsu

Fujitsu

Fujitsu SK-96380-120PMT Manual de usuario

Fujitsu

Fujitsu D1451 Manual de usuario

Fujitsu

Fujitsu D3171 Manual del propietario

Fujitsu

Fujitsu FLASH-CAN-100 Manual de usuario

Fujitsu

Fujitsu D2530 Manual de usuario

Fujitsu

Fujitsu MB86R11 Manual de usuario

Fujitsu

Fujitsu D3161 Manual de usuario

Fujitsu

Fujitsu CW35 Series Manual de usuario

Fujitsu

Fujitsu MB 91F467 Manual de usuario

Fujitsu

Fujitsu D3313-S Manual de usuario

Fujitsu

Fujitsu 8FX MB2146-510-01-E Manual de usuario

Fujitsu

Fujitsu Mainboard D2974 Manual de usuario

Fujitsu

Fujitsu D3231-S Manual de usuario

Fujitsu

Fujitsu MB9B500 Series Manual de usuario

Fujitsu

Fujitsu SK-MB9EF120-002 Manual de usuario

Fujitsu

Fujitsu D2917 Manual de usuario

Fujitsu

Fujitsu D2811 Manual de usuario

Fujitsu

Fujitsu D3003-S Manual de usuario

Fujitsu

Fujitsu SK-91460T-144PMC-GPIO Manual de usuario

Fujitsu

Fujitsu D1919 Manual de usuario

Fujitsu

Fujitsu D1692 Manual de usuario

Fujitsu

Fujitsu Siemens D1160 Manual de usuario

Fujitsu

Fujitsu D2119 Manual de usuario

Fujitsu

Fujitsu FLASH-CAN-64P-350-PMC Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario