Fujitsu Siemens Computers Fujitsu Siemens SCENICVIEW P17-2 Manual de usuario

Monitor

Operating Manual

English

SCENICVIEW

P17-2 / P19-2 / P20-2

SCENICVIEW P17-2 / P19-2 / P20-2

Operation of the monitor

The monitor offers the following possibilities that enable it to be optimally adjusted for the respective

user and the respective situation.

Adjusting height, rake and rotation

The monitor height can be adjusted within a range of approx. 2.5 inch/70 mm.

►Grasp the monitor with both hands on the right and left edge of the casing and move it upward

or downward.

The rake of the monitor can be adjusted by -2° (forward) and +35° (back) from its vertical position.

►Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the

desired rake.

The monitor can be rotated by ± 60° from its centre position.

Ê Grasp the monitor with both hands on the right and left edge of the casing and rotate it into the

desired position.

SCENICVIEW P17-2 / P19-2 / P20-2

Adjusting portrait format

The monitor can be turned from the "wide format" (landscape mode) into the "high format" position

(portrait mode).

Ê Grasp the monitor with both hands on the right and left edge of the casing, move it into the

highest position and turn it clockwise until it is in the portrait position.

You must use corresponding software (pivot software) so that the screen display is also

shown in the portrait mode. This software is included in the delivery (CD-ROM) and must

be installed on your computer.

Ê In the OSD menu you have the option of switching the OSD manually from landscape mode into

portrait mode (see section "Monitor settings using the OSD menu").

To reset the monitor to the landscape mode, the monitor must be turned counter-clockwise. The

OSD display can be reset again in the OSD menu.

Switching the monitor on/off

The main switch at the rear and the ON/OFF switch at the front are used for switching the monitor on

and off.

►Switch the monitor on with the main switch (4) at the rear.

1 = Buttons for the OSD menu

(On-Screen-display)

2 = ON/OFF switch

3 = Power indicator

4 = Main switch

The power indicator (3) lights up blue when the monitor and computer are switched on. The power

indicator lights up orange when the monitor does not receive a video signal or is in the energy saving

mode. The power indicator goes off when the monitor is switched off.

SCENICVIEW P17-2 / P19-2 / P20-2

Changing the monitor settings

When putting the monitor into operation for the first time, the screen display should be optimally

adapted to the screen controller used and adjusted in accordance with your needs.

Choosing basic monitor settings using the supplied software

If one of the operating systems Windows 95/98, Windows NT, Windows Me, Windows 2000,

Windows XP or OS/2 (with Windows emulation installed) is used, the basic monitor settings can be

set with the CD supplied.

►Insert the supplied CD into the CD-ROM drive.

►Open the Readme file on the CD and follow the instructions in the file.

Your monitor should now already be properly adjusted. If none of the above operating systems is

used or minor corrections are to be made to the screen display, then change the monitor settings

with the OSD menu.

Changing the monitor settings with the buttons of the control panel

213

SELECT / MENU EXIT / AUTO

INPUT

1 = Buttons for the OSD menu

(On-Screen-display)

2 = ON/OFF switch

3 = Power indicator

Use the buttons of the control panel to make the following monitor settings directly while the OSD

menu is switched off.

Performing auto-adjustment of the monitor

►Press the AUTO button for approx. 1 second while the OSD menu is switched off.

The Auto Processing message is displayed.

Picture quality and position are set to optimum values for your system.

Selecting input signal (D-SUB/DVI-D)

►Press the INPUT button for calling the Input select setting window.

►Press the

6or 5button to select the desired input (analogue D-SUB or digital DVI-D).

This setting window can also be called, when the OSD menu is locked.

Activating/deactivating muting

►Press the button to switch the sound off and on again.

A message is displayed that the action has been performed.

SCENICVIEW P17-2 / P19-2 / P20-2

Locking the OSD menu

The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.

►Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor

with the ON/OFF switch.

A message is displayed that the action has been performed.

Please proceed in the same manner to release the locked OSD menu again.

Locking the ON/OFF button

The ON/OFF switch can be locked to prevent accidental or unauthorised changes to the monitor

settings.

►Press and hold both buttons 6and 5simultaneously for a few seconds.

A message is displayed that the action has been performed.

Please proceed in the same manner to release the locked ON/OFF switch again.

Monitor settings using the OSD menu

With the buttons on the control panel, call up and use the integrated OSD (On-Screen display) menu.

The OSD menu is available in different languages. The English menu names are used in

the following description (default setting). With the OSD function Language in the OSD Setup

you can select another language.

To set the OSD menu, perform the following steps:

►Press the SELECT/MENU button to activate the OSD menu.

The main menu appears on the screen (on the left-hand side) with icons for the setting functions.

The first symbol (Brightness/Contrast) is

highlighted. In the right-hand part of the display

the associated functions are shown.

►If necessary, press the 6or 5button to

mark another icon (e.g. Image adjust).

►Press the SELECT/MENU button to select

the highlighted icon.

SCENICVIEW P17-2 / P19-2 / P20-2

The corresponding setting window (here: Image Adjust) is displayed (on the right-hand side).

The first function (H-Position) is highlighted.

►If necessary, press the 6or 5button to

mark another function.

►Press the SELECT/MENU button to select

the highlighted function.

►Press the

6or 5button to adjust the

value for the selected function.

►Press the EXIT/AUTO button to exit the

function.

►If necessary, press the button 6or 5to

mark another function or press the

EXIT/AUTO button to return to the main

menu.

All changes are stored automatically.

If you want to change other settings, select the corresponding function from the OSD main menu. All

possible adjustments of the main menu are described in the following.

The OSD menu for analogue monitor operation is described in the following. During digital

operation some functions are not available, as they are not required due to the digital

transmission technology used.

Adjusting the brightness and contrast

Calling the Brightness / Contrast setting window

Brightness Setting the brightness of the display

With this function you change the brightness of the background lighting.

Contrast Setting the contrast of the display

With this function you modify the contrast of bright colour tones.

Black Level Setting the brightness of the display

With this function you modify the contrast of dark colour tones.

Auto Level Setting the brightness of the display

With this function you can automatically set the contrast.

Press the SELECT/MENU button to activate the function.

If the contrast is set too high, bright surfaces can no longer be distinguished from very

bright surfaces. If the contrast is set too low, the maximum brightness will not be achieved.

SCENICVIEW P17-2 / P19-2 / P20-2

Adjusting size and position

Calling the Image adjust setting window

H-Position Adjusting the horizontal position

With this function you move the picture to the left or to the right.

V-Position Adjusting the vertical position

With this function you move the picture up or down.

Clock Setting synchronisation

With this function you adjust the picture width to eliminate vertical picture

disturbances.

Phase Eliminating picture interference

With this function you fine-tune your monitor to eliminate picture interference.

Adjusting the volume

Calling the Audio setting window

Volume Setting the volume for playback with the integrated loudspeakers

Mute Switching the loudspeakers off or on

Setting colour temperature and colours

Calling the Colour setting window

Selecting the colour temperature

The "warmth" of the screen colours is set using the colour temperature. The colour

temperature is measured in K (= Kelvin). You can select from sRGB, 6500 K, 7500 K,

9300 K, Native and Custom Colour.

sRGB

Native

Custom Colour

= setting colour display according to the sRGB standard

= Original colour of the LCD display

= User-defined colours

In the user-defined setting you can change the colour ratios of the basic colours

(red, green, blue) as required.

SCENICVIEW P17-2 / P19-2 / P20-2

Setting display of the OSD menu

Calling the OSD Setup setting window

Language Setting language for the OSD menu

With this function you choose between English (default setting), French, German,

Italian and Spanish as the language for the OSD menu.

OSD

H-Position

Setting the horizontal position of the OSD menu

With this function you move the OSD menu to the left or to the right.

OSD

V-Position

Setting the vertical position of the OSD menu

With this function you move the OSD menu up or down.

OSD

Timeout

Setting the display duration of the OSD menu

With this function you select a value from 10 to 120 seconds.

If the set time expires without a setting being made, the OSD menu is automatically

faded out.

Setting the display format of the OSD menu

With this function you switch the OSD menu from portrait mode to landscape mode

and vice versa.

OSD

Rotation

Off

= The OSD menu is displayed in portrait mode.

= The OSD menu is displayed in landscape mode.

Setting functions in the "Advanced" menu

Calling the Advanced setting window

Input select Selecting input signal

With this function you switch the monitor from the analogue to the digital mode and

vice versa, when two signal sources are connected.

The condition is that the graphic card used supports this function.

Sharpness Adjusting the picture quality in case of interpolation

With this function you set the sharpness of the interpolation filter. Thus the display

can be optimised for pictures or texts.

Resolution

Notifier

Displaying monitor data

The optimum resolution for this monitor is 1280 x 1024 pixels. With the function

activated (On), a message appears on the screen after approx. 30 seconds if a

different resolution is set.

Change the resolution to 1280 x 1024 to achieve optimum picture quality.

With the function deactivated (Off), no message appears.

Factory Recall Activating the factory settings

With this function all settings are reset to the factory settings without prompting for

confirmation.

Press the SELECT/MENU button to activate the function. The Auto Processing

message is displayed.

SCENICVIEW P17-2 / P19-2 / P20-2

Displaying information

Calling the Information setting window

With this function the model designation, serial number, resolution, H/V frequency,

input signal and polarity of the synchronisation signal are displayed.

Notes on ergonomic colour adjustment

If you select colours for the display in your application programmes, take note of the information

below.

The primary colours blue and red on a dark background do not produce the minimum required

contrast of 3:1 and are therefore not suitable for continuous text and data entry.

When using several colours for characters and background and giving the primary colours full

modulation, you can obtain very suitable colour combinations (see the following table):

Characters

Background

black white purple blue cyan green yellow red

black + + - + + + -

white + + + - - - +

purple + + - - - - -

blue - + - + - + -

cyan + - - + - - -

green + - - + - - -

yellow + - + + - - +

red - + - - - - +

+ Colour combination very suitable

- Colour combination not suitable because colour locations are too close together, thin characters

are not identifiable or rigorous focusing is demanded of the human eye.

SCENICVIEW P17-2 / P19-2 / P20-2

Troubleshooting

Should an error occur, first check the following points. If the distortion is still not eliminated, the

monitor should, if possible, be checked on another computer.

If you are unable to solve the problem, please inform our help desk.

Having this problem? Check the following points:

No screen display

(power indicator does not light)

►Check whether the main switch at the rear of the

monitor is switched on.

►Check whether the power cable on the monitor is

connected correctly.

►Check whether the computer is switched on.

No screen display

(power indicator lights)

►Check whether the computer is switched on.

►Check whether the data cable for the monitor is

correctly attached to the monitor port on the

computer.

►Press any key on the computer keyboard - the

computer may be in energy saving mode.

►Alter the brightness and/or contrast until you get a

picture.

Message:

No Signal

►Check whether the data cable for the monitor is

correctly attached to the monitor port on the

computer.

►Check whether the computer is switched on.

Message:

Frequency out of range:

## kHz / ## Hz

Please change the display mode

to 1280 x 1024 with 60 Hz.

Please change the display mode

to 1600 x 1200 with 60 Hz.

The input signal (horizontal frequency and refresh rate)

at the displayed input does not correspond to the

technical monitor data.

►Adjust the video frequency range using the

computer software (see documentation for your

computer or your graphics card).

►Adjust a different screen resolution using the

computer software (see documentation for your

computer or your screen controller).

P17-2/P19-2 P20-2

1280 x 1024 1600 x 1200

Picture position not correct The monitor recognises an undefined mode (see the

"Technical data" chapter).

►Press the EXIT/AUTO button to perform the auto-

adjustment of the screen.

Picture is shaking ►Check whether the data cable for the monitor is

correctly attached to the monitor port on the

computer.

►Press the EXIT/AUTO button to perform the auto-

adjustment of the screen.

Otros manuales para Fujitsu Siemens SCENICVIEW P17-2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Fujitsu Siemens Computers

Fujitsu Siemens Computers

Fujitsu Siemens Computers L19W-9 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers L17-8 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers 4612 FA Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers 19P2 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers 21P3 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers 4312 FA Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers Fujitsu Siemens SCENICVIEW P17-2 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers MCM 171E Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers SCENICVIEW P17-1A Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers SCENICVIEW B17-3 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers SCENICVIEW B15-1A Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers FGSW-1602 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers SCALEOVIEW S17-2 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers SCALEOVIEW L17-2 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers FSC B15-1A Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers SCALEOVIEW Q22W-1 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers 3815 FA Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers MCM 21P2 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers 383V FA Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers 461V FA Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers SCENICVIEW A17-3A Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers D22W-1 Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers 5110 FA Manual de usuario

Fujitsu Siemens Computers

Fujitsu Siemens Computers L24W-4 Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación