Front Runner LATF002 Manual de usuario
LATF002_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
front runner
LATF002
ENG
1
Thank you for purchasing a Front Runner Toyota 4Runner Ladder.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
TOYOTA 4RUNNER LADDER
LATF002_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
IN THE BOX
1 1 X Ladder Top Step Bracket
2 4 X Top Mount Bracket
3 2 X Ladder Side Profile
4 1 X Bottom Mount Bracket
5 1 X Door Clamp Bracket
6 1 X Bottom Clamp Bracket
7 1 X Bottom Inner Mount PLT
8 3 X Ladder Step
9 6 X Thread Forming Screw M6 x 25
10 10 X M6 x 16 Button Head Bolt
11 3 X M6 x 25 Button Head Bolt
12 4 X M8 x 20 Button Head Bolt
13 4 X M8 x 16 x 1.6 Flat Washer
14 3 X M6 Cage Nut
15 6 X M8 Nyoc Nut
IN THE BOX
16 1 X Pinch Bracket
17 10 X M6 Nyloc Nut
18 10 X M6 Nut Cap
19 6 X M8 Nut Cap
20 1 X U-Channel Rubber (200mm Long)
19
15
16
5
1
10
2
17
18
8
3
10
9
7
14
4
12
6
11
20
13
19 15
Torx
T30 Anti-
Rust
Anti-
Seize
4mm
5mm
4mm
7mm
Marker
10mm
13mm
Masking
Tape
Denatured
Alcohol
100mm
LATF002_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE
2
2.1
2.2
2.3
Loosly assemble the Ladder Side Profile's
(Item 3) to the Ladder Top Step Bracket
(Item 1) using the Top Mount Brackets, M6
x 16 Button Head Bolts and M6 Nyloc Nuts
(Items 2, 10 & 17).
Secure the Bottom Mount Bracket and
Ladder Rungs (Item 4 & 8) to the Ladder
Side Profiles (Item 3) using M6 x 25 Thread
Forming Screws, M6 x 16 Button Head Bolts
and M6 Nyloc Nuts (Items 9, 10 & 17). Fully
Tighten all Fasteners.
Place M6 Nut Caps (Item 18) over all Nyloc
Nuts.
Measuree 100mm from the inside edge of
the spoiler trim, along the hatch edge and
mark with masking tape (A) as shown.
A
Apply a little Anti Seize / oil on Thread
Forming Screws before inserting. Note
these are thread forming screws.
Tightening Torque 8-10Nm /
5.9 ft lb - 7.38 ft lb. Take care when
using a cordless driver.
1
10
2
3
10mm
4mm
10mm
4mm
Torx
T30
9
10
LATF002_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE
2
2.4
2.5
2.6
Clean the surface where the Top Mount
Bracket (Item 5) will be secured with
de-natured alchohol.
Remove the backing tape of the self-adhe-
sive tape on the bottom of the Top Mount
Bracket (Item 5) and hook the Top Mount
Bracket (Item 5) over the the top hatch
edge.
Position the Top Mount Bracket (Item 5) next
to the masking tape.
Press on the front hook, making sure the
hook is evenly pressed up against the hatch
top edge.
Remove the masking tape and firmly press
the Top Mount Bracket (Item 5) down to
secure the bracket to the hatch.
Hook the Ladder assembly from 2.1 and 2.2
over the Top Mount Bracket.
Making sure it is level, mark the Bottom
position of the ladder with masking tape as
shown (A).
Remove the Ladder assembly.
Open the Rear hatch and remove the left
hand side handle as shown.
A
Denatured
Alcohol
5
LATF002_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
5
FIT AND SECURE
2
2.7
2.8
2.9
Align the left hand side (A) of the the
Bottom Clamp Bracket with the masking
tape applied in 2.5 and press the bracket
up against the door so the the door hatch
sits in the slot (B).
Mark the hole centers (C) as shown. Drill a
4mm Pilot hole and open up to 7mm.
Assemble the M6 Cage Nuts (Item 14) to the
Bottom Inner Plate (Item 7) as shown.
Slide the Bottom Inner Plate into the Door
hatch as shown.
A C
C
C
B
6
4mm
7mm
Anti-
Rust
LATF002_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
6
FIT AND SECURE
2
2.10
2.11
2.12
Place the U-Channel Rubber (Item 20) over
the Door Edge where the Bottom Clamp
Bracket (Item 6) will be secured.
Secure the Bottom Clamp Plate (Item 6) to
the Bottom Inner Plate (Item 7) using M6 x
25 Button Head Bolts.
Open the rear door and loosen and remove
the right hand screw on the left hand door
hinge (A).
Ensure the Top Mount Brackets (Item 5)
hooks are against the top ede of the rear
door. Place the Pinch Bracket (Item 16) over
the Top Mount Brackets (Item 5) hooks,
lining up the slotted hole with the screw
hole.
Secure the Pinch Bracket (Item 16) to the
vehicle using the bolt removed earlier. Fully
tighten.
Hook The Ladder assembly from 2.1 and
2.2 over the Top Mount Bracket (Item 5) as
shown and loosly assemble using M8 Nyloc
Nuts (Item 15). Do not Fully tighten yet.
13mm
4mm
16
A
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
LATF002_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
7
FIT AND SECURE
2
2.13
Secure the Ladder assembly to the Bottom
Mount Bracket (Item 6) using M8 x 25 Button
Head Bolt, M8 x 16 x 1.6 Flat Washers and
M8 Nyloc Nuts (Item 13 & 15). Fully tighten
all fasteners.
Place M8 Nut Caps (Item 19) over M8 Nyloc
Nuts (Item 19).
TIP: Start with the forward LH and RH
fasteners, alternating between fasteners
to pull the Ladder evenly.
13mm
5mm
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Front Runner
Front Runner
Front Runner SSDS602 Manual de usuario
Front Runner
Front Runner SSDS111 Manual de usuario
Front Runner
Front Runner TBRA034 Manual de usuario
Front Runner
Front Runner RRAC018 Manual de usuario
Front Runner
Front Runner SSLD001 Manual de usuario
Front Runner
Front Runner FSLI021 Manual de usuario
Front Runner
Front Runner SSBS008 Manual de usuario
Front Runner
Front Runner FAJL004 Manual de usuario
Front Runner
Front Runner FATT002 Manual de usuario
Front Runner
Front Runner TBRA020 Manual de usuario
Front Runner
Front Runner FSLI023 Manual de usuario
Front Runner
Front Runner LALD004 Manual de usuario
Front Runner
Front Runner SSDS113 Manual de usuario
Front Runner
Front Runner KRJW021T Manual de usuario
Front Runner
Front Runner KSTF003T Manual de usuario
Front Runner
Front Runner SLIMLINE II TRAY Manual de usuario
Front Runner
Front Runner SSDS110 Manual de usuario
Front Runner
Front Runner TBMK009 Manual de usuario
Front Runner
Front Runner RRAC120 Manual de usuario
Front Runner
Front Runner FAFE001 Manual de usuario
