Freescale Semiconductor PE Micro Cyclone Pro Manual de usuario

Purchase Agreement

P&E Microcomputer Systems, Inc. reserves the right to make changes without further notice to any products herein to

improve reliability, function, or design. P&E Microcomputer Systems, Inc. does not assume any liability arising out of

the application or use of any product or circuit described herein.

This software and accompanying documentation are protected by United States Copyright law and also by

International Treaty provisions. Any use of this software in violation of copyright law or the terms of this agreement will

be prosecuted.

All the software described in this document is copyrighted by P&E Microcomputer Systems, Inc. Copyright notices

have been included in the software.

P&E Microcomputer Systems authorizes you to make archival copies of the software and documentation for the sole

purpose of back-up and protecting your investment from loss. Under no circumstances may you copy this software or

documentation for the purpose of distribution to others. Under no conditions may you remove the copyright notices

from this software or documentation.

This software may be used by one person on as many computers as that person uses, provided that the software is

never used on two computers at the same time. P&E expects that group programming projects making use of this

software will purchase a copy of the software and documentation for each user in the group. Contact P&E for volume

discounts and site licensing agreements.

P&E Microcomputer Systems does not assume any liability for the use of this software beyond the original purchase

price of the software. In no event will P&E Microcomputer Systems be liable for additional damages, including any

lost profits, lost savings or other incidental or consequential damages arising out of the use or inability to use these

programs, even if P&E Microcomputer Systems has been advised of the possibility of such damage.

By using this software, you accept the terms of this agreement.

MS-DOS & Windows are registered trademarks of Microsoft Corporation. IBM is a registered trademark of IBM

corporation.

Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service

names are the property of their respective owners.

P&E Microcomputer Systems, Inc.

98 Galen St.

Watertown, MA 02472

617-923-0053

http://www.pemicro.com

CYCLONEPROUM

Manual version 1.13

January 2011

Cyclone PRO User Manual i

CYCLONE PRO

1 INTRODUCTION ............................................................................................ 1

2 QUICK START GUIDE FOR SAP OPERATION ............................................ 5

3 CYCLONE PRO HARDWARE........................................................................ 8

3.1 Cyclone PRO Power Supply .......................................................................... 8

3.2 RS232 Communication .................................................................................. 8

3.3 Ethernet Communication................................................................................ 9

3.4 USB Communications .................................................................................... 9

3.5 Electromechanical Relays ............................................................................ 10

3.6 Power Connectors........................................................................................ 11

3.7 Jumper Settings ........................................................................................... 11

3.8 Optional Oscillator (MON08 Only)................................................................ 12

3.9 Target BDM Connector ................................................................................ 12

3.10 Target MON08 Connector ............................................................................ 13

3.11 Ribbon Cable................................................................................................ 15

3.12 Target Power Management.......................................................................... 15

3.13 CompactFlash Port....................................................................................... 21

4 CYCLONE LCD MENU................................................................................. 23

4.1 Status Window ............................................................................................. 24

4.2 Main Menu.................................................................................................... 25

5 STAND-ALONE PROGRAMMER CONFIGURATION.................................. 31

5.1 Create A Stand-Alone Programming (SAP) Image ...................................... 31

5.2 Manage Multiple SAP Images ...................................................................... 45

6 STAND-ALONE PROGRAMMER MANUAL CONTROL .............................. 48

6.1 Operation Via Cyclone PRO Buttons ........................................................... 48

6.2 Operation Via LCD Menu (Rev. C Only) ...................................................... 50

6.3 Cyclone Battery Pack ................................................................................... 54

7 STAND-ALONE PROGRAMMER AUTOMATED CONTROL....................... 55

7.1 Cyclone Automated Control Package - Overview ........................................ 55

7.2 Cyclone Automated Control Package - Details ............................................ 56

8 PC-HOSTED DEBUG/PROGRAMMING SOFTWARE................................. 58

ii Cyclone PRO User Manual

CYCLONE PRO

8.1 P&E Microcomputer Systems Software........................................................58

8.2 Freescale Software .......................................................................................61

8.3 HC08 P&E Multilink/Cyclone PRO Connections...........................................65

8.4 HCS08 P&E Multilink/Cyclone PRO Connections ........................................84

9 ETHERNET CONFIGURATION ................................................................... 92

9.1 Network Architectures...................................................................................92

9.2 Network Parameters .....................................................................................93

9.3 Internet Protocol ...........................................................................................94

9.4 Connecting The Cyclone Device ..................................................................94

9.5 Cyclone IP Setup Via LCD Menu..................................................................96

9.6 Cyclone IP Setup Utility User Interface (ConfigureIP) ..................................96

9.7 Using ConfigureIP.exe To Configure The Cyclone PRO ..............................98

10 SERIAL PORT CONFIGURATION............................................................. 101

11 USB PORT CONFIGURATION .................................................................. 102

12 AUTOMATIC SERIAL NUMBER MECHANISM ......................................... 103

12.1 Understanding Serialization........................................................................103

12.2 Serialize Utility ............................................................................................104

12.3 Serialize Utility Example .............................................................................107

12.4 Using Serial Number File............................................................................107

12.5 Serial Number Handling in Cyclone PRO ...................................................108

13 TARGET MON08 HEADER PINOUTS....................................................... 110

13.1 68HC908AB................................................................................................110

13.2 68HC908AP................................................................................................111

13.3 68HC908AS................................................................................................112

13.4 68HC908AT ................................................................................................113

13.5 68HC908AZ ................................................................................................114

13.6 68HC908BD................................................................................................115

13.7 68HC908EY................................................................................................116

13.8 68HC908GP ...............................................................................................117

13.9 68HC908GR16/32 ......................................................................................118

13.10 68HC908GR4/8 ..........................................................................................119

Cyclone PRO User Manual iii

CYCLONE PRO

13.11 68HC908GT ............................................................................................... 120

13.12 68HC908GZ ............................................................................................... 121

13.13 68HC908JB1/8 ........................................................................................... 122

13.14 68HC908JB12 ............................................................................................ 123

13.15 68HC908JB16 ............................................................................................ 124

13.16 68HC908JG................................................................................................ 125

13.17 68HC908JK ................................................................................................ 126

13.18 68HC908JL ................................................................................................ 127

13.19 68HC908JR................................................................................................ 128

13.20 68HC908JW ............................................................................................... 128

13.21 68HC908KX ............................................................................................... 129

13.22 68HC908LB................................................................................................ 130

13.23 68HC908LD................................................................................................ 131

13.24 68HC908LJ ................................................................................................ 132

13.25 68HC908LK................................................................................................ 133

13.26 68HC908LT ................................................................................................ 134

13.27 68HC908LV................................................................................................ 135

13.28 68HC908MR4/8.......................................................................................... 136

13.29 68HC908MR16/32...................................................................................... 136

13.30 68HC908QL ............................................................................................... 137

13.31 68HC908QB ............................................................................................... 138

13.32 68HC908QC............................................................................................... 139

13.33 68HC908QT ............................................................................................... 140

13.34 68HC908QY ............................................................................................... 141

13.35 68HC908RF ............................................................................................... 142

13.36 68HC908RK ............................................................................................... 143

13.37 68HC908SR ............................................................................................... 144

14 CYCLONE ERROR CODES....................................................................... 145

14.1 Debug Mode Communication Errors .......................................................... 145

14.2 SAP Image Handling Errors ....................................................................... 145

14.3 SAP Algorithm Header Operation Handling Errors .................................... 146

iv Cyclone PRO User Manual

CYCLONE PRO

14.4 SAP Operation Errors .................................................................................146

14.5 SAP Blank Check Range and Module Errors .............................................146

14.6 SAP Erase Range and Module Errors ........................................................146

14.7 SAP Program Byte, Word, and Module Errors............................................146

14.8 SAP Verify Checksum Errors......................................................................147

14.9 SAP Verify Range and Module Errors ........................................................147

14.10 SAP User Function Errors ..........................................................................147

14.11 SAP Trim Errors..........................................................................................147

14.12 Unrecoverable Fatal Errors.........................................................................147

14.13 External Memory Errors ..............................................................................148

14.14 Serial Number Errors ..................................................................................149

14.15 Successful Download Counter Errors .........................................................149

Cyclone PRO User Manual 1

CYCLONE PRO

1 INTRODUCTION

The Cyclone PRO is both a powerful production programmer and a versatile

development/debugging tool for Freescale microcontroller-based hardware

architectures.

The Cyclone PRO is designed to withstand the demands of a production

environment. It is a Stand-Alone Programmer (SAP) that can be operated

manually or used to host automated programming. In manual SAP mode the

unit is operated using buttons and/or the LCD Menu. Host-controlled SAP

mode, for automated programming, is accomplished using either a command

line utility, RS232 protocol, UDP protocol, or the Cyclone Automated Control

DLL.

The Cyclone PRO is also a very effective development tool. It can operate

interactively with a PC for development debugging and programming, and

conveniently supports multiple communication interfaces.

The following features help make the Cyclone PRO such a versatile tool for

both production and debug:

• Multiple Freescale Architecture Support

• ColdFire V1

•HCS08

•RS08

•HC(S)12(X)

•HC908(MON08)

• Versatile Light Touch Buttons

• Performs Stand-Alone Programming (SAP) operations

• Navigates LCD menu

• Resets Cyclone PRO

2 Cyclone PRO User Manual

CYCLONE PRO

• Powerful LCD Menu

• Executes SAP operations

• Selects SAP image

• Configures Cyclone PRO IP settings

• Displays operation status

• Convenient LED Display

• Shows programming status during operation

• Indicates success or specifies source of failure

• Multiple Communication Interfaces

• Ethernet 10/100 baseT

• USB 1.1

• Serial Baud 115200, no parity, 8 data bits, 1 stop bit (adjustable to

57600 Baud for RS232 controlled production environment)

• Multiple Storage Media

• 3 Megabytes of onboard storage. Stores data to be programmed,

programming algorithms, and any necessary configuration settings.

• CompactFlash support available with purchase of CompactFlash

activation license.

• Versatile Power Management

• Uses electromechanical relays to automatically cycle target power

when necessary during security protocol (MON08) and BDM mode

entry.

• Jumper-settable power management schemes for MON08 and

BDM targets.

• Automatically supplies Vpp voltage for RS08 targets during flash

erasing and programming operations.

• Multiple Voltage Operation

• Automatically detects and caters to target voltages ranging from

1.8V to 5V.

Cyclone PRO User Manual 3

CYCLONE PRO

• Multiple Frequency Operation

• Automatically detects and caters to target bus frequencies or BDM

frequencies ranging from 1MHz to 8MHz (MON08) or 16KHz to

50MHz (BDM).

• Provides a 9.8304 MHz or 4.1952 MHz oscillator signal to overdrive

target crystal and RC clock circuitry (MON08).

• Dynamic Signal Configuration

• Software-configurable port-pin settings for Monitor ROM entrance.

• Multiple SAP Images

• Onboard Flash stores up to 8 images.

• CompactFlash (if activated) stores more than 200 images.

• Images for different architectures can co-exist.

• Multiple Memory Modules In One SAP Image

• Supports multiple programming algorithms for internal or external

memory modules such as EEPROM and Flash.

• Automatic Serial Number Mechanism

• Supports serial number programming and automatic

incrementation

• Supports multiple serial number structures within each SAP Image.

• Powerful Automated Control Package For Production Control

• Basic Automated Control Package (included) supports host-

controlled SAP operations for one Cyclone PRO. Professional and

Enterprise Automated Control Packages available for purchase.

• Multiple Cyclone PROs can create a Gang Programmer using a

variety of different communication interfaces.

• Different SAP Images on different Cyclone PROs can execute

simultaneously.

• Mixed-architecture targets can perform SAP operations

simultaneously.

4 Cyclone PRO User Manual

CYCLONE PRO

• Versatile Debugging and Programming Software

• Free image creation utility, image management utility, and IP

configuration utility

• Includes free debugger and programmer for HC908 targets

• Includes free programmer for ColdFire V1, HC9S08, RS08, and

HC(S)12(X) targets

• Debugger for ColdFire V1, HC9S08, RS08, and HC(S)12(X) targets

available for purchase

• Activation license for CompactFlash support available for purchase

The Cyclone PRO is an all-in-one solution for production programming and

debugging of Freescale microcontroller-based hardware.

Tabla de contenidos

Otros manuales de Placa madre de Freescale Semiconductor

Freescale Semiconductor

Freescale Semiconductor M5211DEMO Manual de usuario

Freescale Semiconductor

Freescale Semiconductor DEMO908QB8 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MPC5777C EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33816AEEVM Manual de usuario

Freescale Semiconductor

Freescale Semiconductor FRDM-17C724-EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MQX RTOS Manual de usuario

Freescale Semiconductor

Freescale Semiconductor TWR-K60N512-KEIL Manual de usuario

Freescale Semiconductor

Freescale Semiconductor FRDM-FXS-MULTI-B Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KITVR500EVM Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33730EKEVBE Manual de usuario

Freescale Semiconductor

Freescale Semiconductor FRDM-KL46Z Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MED-SPI Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MPC5748G EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33912EVME Manual

Freescale Semiconductor

Freescale Semiconductor DSPD56362EVM Guía de inicio rápido

Freescale Semiconductor

Freescale Semiconductor Babbage 2.5 Guía del usuario

Freescale Semiconductor

Freescale Semiconductor TWR-K80F150M Manual de usuario

Freescale Semiconductor

Freescale Semiconductor PowerQUICC MPC885 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor USB-KW019032 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MSC8156 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor 33395 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor K20D72M Manual de usuario

Freescale Semiconductor

Freescale Semiconductor T4240 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MCIMX53SMD Manual de instalación

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario