Freescale Semiconductor FRDM-KL25Z Manual de usuario

Freescale Semiconductor, Inc. FRDMKL25ZUM

FRDM-KL25Z User's Manual

2012-09-24

Rev. 1.0

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 2 of 14

Table of Contents

1Overview.....................................................................................................................................................3

2Reference Documents ............................................................................................................................3

3Getting Started..........................................................................................................................................3

4FRDM-KL25Z Hardware Overview ....................................................................................................4

5FRDM-KL25Z Hardware Description................................................................................................5

5.1 Power Supply........................................................................................................................................................................5

5.2 Serial and Debug Adapter (OpenSDA) .......................................................................................................................7

5.2.1 Debug Interface...................................................................................................................................................................................7

5.2.2 Virtual Serial Port............................................................................................................................................................................... 8

5.3 KL25Z Microcontroller.....................................................................................................................................................8

5.3.1 Clock Source .........................................................................................................................................................................................9

5.3.2 USB Interface........................................................................................................................................................................................9

5.3.3 Serial Port ..............................................................................................................................................................................................9

5.3.4 Reset.........................................................................................................................................................................................................9

5.3.5 Debug.................................................................................................................................................................................................... 10

5.4 Capacitive Touch Slider................................................................................................................................................. 10

5.5 3-axis Accelerometer......................................................................................................................................................10

5.6 RGB LED...............................................................................................................................................................................10

5.7 Input/Output Connectors.............................................................................................................................................11

5.8 Arduino Compatibility...................................................................................................................................................12

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 3 of 14

1Overview

The Freescale Freedom development platform is a set of software and hardware tools for evaluation

and development. It is ideal for rapid prototyping of microcontroller-based applications. The Freescale

Freedom KL25Z hardware, FRDM-KL25Z, is a simple, yet sophisticated design featuring a Kinetis L series

microcontroller, the industry’s first microcontroller built on the ARM® Cortex™-M0+ core.

FRDM-KL25Z can be used to evaluate the KL1 and KL2 Kinetis L series devices. It features a

KL25Z128VLK, a KL2 family device boasting a max operating frequency of 48MHz, 128KB of flash, a full-

speed USB controller, and loads of analog and digital peripherals. The FRDM-KL25Z hardware is form-

factor compatible with the Arduino™ R3 pin layout, providing a broad range of expansion board

options. The on-board interfaces include an RGB LED, a 3-axis digital accelerometer, and a capacitive

touch slider.

The FRDM-KL25Z is the first hardware platform to feature the Freescale open standard embedded

serial and debug adapter known as OpenSDA. This circuit offers several options for serial

communications, flash programming and run-control debugging.

2Reference Documents

The table below provides a list of reference documents for the FRDM-KL25Z hardware. All of these

documents are available online at www.freescale.com/FRDM-KL25Z.

Table 1. FRDM-KL25Z Reference Documents

Filename

Description

FRDM-KL25Z Quick Start Package

Quick Start Guide and supporting files for getting started with

the FRDM-KL25Z.

FRDM-KL25Z User’s Manual

This document—overview and detailed information for the

FRDM-KL25Z hardware.

FRDM-KL25Z Pinouts

Spreadsheet of pin connections for all MCU pins. Includes

pinout for the I/O headers, Arduino R3 compatibility chart,

and OpenSDA MCU pinout.

FRDM-KL25Z Schematics

PDF schematics for the FRDM-KL25Z hardware

FRDM-KL25Z Design Package

Zip file containing all design source files for the FRDM-KL25Z

hardware

OpenSDA User’s Guide

Overview and instructions for use of the OpenSDA embedded

debug circuit

3Getting Started

Refer to the FRDM-KL25Z Quick Start Package for step-by-step instructions for getting started with the

FRDM-KL25Z. See the Jump Start Your Design section onwww.freescale.com/FRDM-KL25Z for the

Quick Start Package and software lab guides.

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 4 of 14

4FRDM-KL25Z Hardware Overview

The features of the FRDM-KL25Z include:

MKL25Z128VLK4 in an 80 LQFP package

Capacitive touch slider

MMA8451Q accelerometer

Tri-color (RGB) LED

Flexible power supply options –USB, coin cell battery, external source

Battery-ready, power-measurement access points

Easy access to MCU I/O via Arduino ™ R3 compatible I/O connectors

Programmable OpenSDA debug interface with multiple applications available including:

-Mass storage device flash programming interface

-P&E Debug interface provides run-control debugging and compatibility with IDE tools

-CMSIS-DAP interface: new ARM standard for embedded debug interface

-Data logging application

Figure 1 shows a block diagram of the FRDM-KL25Z design. The primary components and their

placement on the hardware assembly are pointed out in Figure 2.

Figure 1. FRDM-KL25Z Block Diagram

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 5 of 14

Figure 2. FRDM-KL25Z Feature Call-outs

5FRDM-KL25Z Hardware Description

5.1 Power Supply

There are multiple power supply options on the FRDM-KL25Z. It can be powered from either of the

USB connectors, the VIN pin on the I/O header, an on-board coin cell battery, or an off-board 1.71-3.6V

supply from the 3.3V pin on the I/O header. The USB and VIN supplies are regulated on-board using a

3.3V linear regulator to produce the main power supply. The other two sources are not regulated on-

board. Table 2 provides the operational details and requirements for the power supplies.

Table 2. Power Supply Requirements

Supply Source

Valid Range

OpenSDA

Operational?

Regulated on-

board?

OpenSDA USB (J7)

Yes

KL25Z USB (J5)

Yes

VIN Pin

4.3-9V

Yes

3.3V Pin

1.71-3.6V

Coin Cell Battery

1.71-3.6V

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 6 of 14

Note that the OpenSDA circuit is only operational when a USB cable is connected and supplying power

to J7. However, protection circuitry is in place to allow multiple sources to be powered at once.

Figure 3 shows the schematic drawing for the power supply inputs and the on-board voltage regulator.

Figure 3. Power Supply Schematic

Table 3. FRDM-KL25Z Power Supplies

Power Supply Name

Description

P5-9V_VIN

Power supplied from the VIN pin of the I/O headers (J9 pin 16).

P5V_SDA

Power supplied from the OpenSDA USB connector (J7). A Schottky

diode provides back drive protection.

P5V_KL25Z

Power supplied from the KL25Z USB connector (J5). A Schottky diode

provides back drive protection.

P3V3_VREG

Regulated 3.3V supply. Sources power to the P3V3 supply rail

through a back drive protection Schottky diode. 1

P3V3_BATT

Coin cell battery supply voltage. Sources power to the P3V3 supply

rail through a back drive protection Schottky diode.

P3V3

Main supply rail for the FRDM-KL25Z assembly. May be sourced from

P3V3_VREG, P3V3_BATT, or directly from the I/O headers (J9 pin 8)

P3V3_KL25Z

KL25Z MCU supply. Header J4 provides a convenient means for

energy consumption measurements. 2

P3V3_SDA

OpenSDA circuit supply. Header J3 provides a convenient means for

energy consumption measurements. 2

P5V_USB

Nominal 5V supplied to the I/O headers (J9 pin 10). Sourced from

either the P5V_KL25Z or P5V_OSDA supply through a back drive

protection Schottky diode.

NOTES:

1) By default the linear regulator, U1, is a 3.3V output regulator. However, this is a

common footprint that would allow the user to modify the assembly to utilize an

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 7 of 14

alternative device such as a 1.8V or 2.5V regulator. The KL25Z microcontroller has an

operating range of 1.71V to 3.6V.

2) J3 and J4 are not populated by default. The two pins of these headers are shorted

together by a trace on the bottom layer of the PCB. To measure the energy

consumption of either the KL25Z or the OpenSDA MCU, the trace between these pins

must first be cut. A current probe or a shunt resistor and voltage meter can then be

applied to measure the energy consumption on these rails.

5.2 Serial and Debug Adapter (OpenSDA)

OpenSDA is an open-standard serial and debug adapter. It bridges serial and debug communications

between a USB host and an embedded target processor as shown in Figure 4. The hardware circuit is

based on a Freescale Kinetis K20 family microcontroller (MCU) with 128 KB of embedded flash and an

integrated USB controller. OpenSDA features a mass storage device (MSD) bootloader, which provides

a quick and easy mechanism for loading different OpenSDA Applications such as flash programmers,

run-control debug interfaces, serial-to-USB converters, and more. Refer to the OpenSDA User’s Guide

for more details.

Figure 4. OpenSDA High-Level Block Diagram

OpenSDA is managed by a Kinetis K20 MCU built on the ARM® Cortex™-M4 core. The OpenSDA circuit

includes a status LED (D4) and a pushbutton (SW1). The pushbutton asserts the Reset signal to the

KL25Z target MCU. It can also be used to place the OpenSDA circuit into Bootloader mode. SPI and

GPIO signals provide an interface to either the SWD debug port of the KL25Z. Additionally, signal

connections are available to implement a UART serial channel. The OpenSDA circuit receives power

when the USB connector J7 is plugged into a USB host.

5.2.1 Debug Interface

Signals with SPI and GPIO capability are used to connect directly to the SWD of the KL25Z. These

signals are also brought out to a standard 10-pin (0.05”) Cortex Debug connector (J6). It is possible to

isolate the KL25Z MCU from the OpenSDA circuit and use J6 to connect to an off-board MCU. To

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 8 of 14

accomplish this, cut the trace on the bottom side of the PCB that connects J11 pin 1 to J11 pin 2. This

will disconnect the SWD_CLK pin to the KL25Z so that it will not interfere with the communications to

an off-board MCU connected to J6.

Figure 5. SWD Debug Connector

Note that J6 is not-populated by default. A Samtec FTSH-105-02-F-D or compatible connector can be

added to the J6 through-hole connector. A mating cable, such as a Samtec FFSD IDC cable, can then be

used to connect from the OpenSDA of the FRDM-KL25Z to an off-board SWD connector.

5.2.2 Virtual Serial Port

A serial port connection is available between the OpenSDA MCU and pins PTA1 and PTA2 of the KL25Z.

Several of the default OpenSDA Applications provided by Freescale, including the MSD Flash

Programmer and the P&E Debug Application, provide a USB Communications Device Class (CDC)

interface that bridges serial communications between the USB host and this serial interface on the

KL25Z.

5.3 KL25Z Microcontroller

The target microcontroller of the FRDM-KL25Z is the KL25Z128VLK4, a Kinetis L series device in an 80

LQFP package. The KL25Z MCU features include:

32-bit ARM Cortex-M0+ core

-up to 48 MHz operation

-Single-cycle fast I/O access port

Memories

-128 KB flash

-16 KB SRAM

System integration

-Power management and mode controllers

-Low-leakage wakeup unit

-Bit manipulation engine for read-modify-write peripheral operations

-Direct memory access (DMA) controller

-Computer operating properly (COP) Watchdog timer

Clocks

-Clock generation module with FLL and PLL for system and CPU clock generation

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 9 of 14

-4 MHz and 32 kHz internal reference clock

-System oscillator supporting external crystal or resonator

-Low-power 1kHz RC oscillator for RTC and COP watchdog

Analog peripherals

-16-bit SAR ADC w/ DMA support

-12-bit DAC w/ DMA support

-High speed comparator

Communication peripherals

-Two 8-bit Serial Peripheral Interfaces (SPI)

-USB dual-role controller with built-in FS/LS transceiver

-USB voltage regulator

-Two I2C modules

-One low-power UART and two standard UART modules

Timers

-One 6-channel Timer/PWM module

-Two 2-channel Timer/PWM modules

-2-channel Periodic Interrupt Timer (PIT)

-Real time clock (RTC)

-Low-power Timer (LPT)

-System tick timer

Human-Machine Interfaces (HMI)

-General purpose input/output controller

-Capacitive touch sense input interface hardware module

5.3.1 Clock Source

The Kinetis KL2 microcontrollers feature an on-chip oscillator compatible with three ranges of input

crystal or resonator frequencies: 32-40 kHz (low freq. mode), 3-8 MHz (high freq. mode, low range) and

8-32 MHz (high freq. mode, high range). The KL25Z128 on the FRDM-KL25Z is clocked from an 8 MHz

crystal.

5.3.2 USB Interface

The Kinetis KL2 microcontrollers feature a dual-role USB controller with on-chip full-speed and low-

speed transceivers. The USB interface on the FRDM-KL25Z is configured as a full-speed USB device. J5

is the USB connector for this interface.

5.3.3 Serial Port

The primary serial port interface signals are PTA1 and PTA2. These signals are connected to both the

OpenSDA and to the J1 I/O connector.

5.3.4 Reset

The PTA20/RESET signal on the KL25Z128 is connected externally to a pushbutton, SW1, and also to the

OpenSDA circuit. The reset button can be used to force an external reset event in the target MCU. The

reset button can also be used to force the OpenSDA circuit into bootloader mode. Please refer to

section 5.2, Serial and Debug Adapter (OpenSDA), for more details.

FRDMKL25ZUM FRDM-KL25Z User's Manual Page 10 of 14

5.3.5 Debug

The sole debug interface on all Kinetis L Series devices is a Serial Wire Debug (SWD) port. The primary

controller of this interface on the FRDM-KL25Z is the onboard OpenSDA circuit (see section 5.2).

However, an unpopulated 10-pin (0.05”) Cortex Debug connector, J6, provides access to the SWD

signals. The Samtec FTSH-105-02-F-D or compatible connectors can be added to the J6 through-hole

debug connector to allow for an external debug cable to be connected.

5.4 Capacitive Touch Slider

Two Touch Sense Input (TSI) signals, TSI0_CH9 and TSI0_CH10, are connected to capacitive electrodes

configured as a touch slider. Freescale’s Touch Sense Software (TSS) provides a software library for

implementing the capacitive touch slider.

5.5 3-axis Accelerometer

A Freescale MMA8451Q low-power, three-axis accelerometer is interfaced through an I2C bus and two

GPIO signals as shown in Table 4 below. By default, the I2C address is 0x1D (SA0 pulled high).

Table 4. Accelerometer Signal Connections

MMA8451Q

KL25Z128

SCL

PTE24

SDA

PTE25

INT1

PTA14

INT2

PTA15

Figure 6. MMA8451Q Schematic Diagram

5.6 RGB LED

Three PWM-capable signals are connected to a red, green, blue LED, D3. The signal connections are

shown in Table 5 below.

Otros manuales para FRDM-KL25Z

Tabla de contenidos

Otros manuales de Placa madre de Freescale Semiconductor

Freescale Semiconductor

Freescale Semiconductor MPC5675EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor kinetis TWR-SMPS-LVFB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33810EKEVME Manual de usuario

Freescale Semiconductor

Freescale Semiconductor Freedom FRDM-KE15Z Manual de usuario

Freescale Semiconductor

Freescale Semiconductor 56800E Manual de usuario

Freescale Semiconductor

Freescale Semiconductor FRDM-KL27Z Manual de usuario

Freescale Semiconductor

Freescale Semiconductor TWR-S12G240 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor Freedom FRDM-KW24D512 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MED-SPI Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MPC5668EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor USB-KW019032 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor PowerQUICC MPC885 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor TWR-K70F120M Manual de usuario

Freescale Semiconductor

Freescale Semiconductor T4240 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor LS1043ARDB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor TWR-MPC5125 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor DSPD56362EVM Guía de inicio rápido

Freescale Semiconductor

Freescale Semiconductor FRDM-17C724-EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MCF5206eLITE Manual de usuario

Freescale Semiconductor

Freescale Semiconductor QorIQ T1023 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor DEMO908GZ60 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor PE Micro Cyclone Pro Manual de usuario

Freescale Semiconductor

Freescale Semiconductor S12ZVC Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT22XS4200EKEVB Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario