FRC inView 360 Fusion Manual de usuario
inView 360 Fusion
Installation Guide
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 2
inView 360 Fusion Installation Guide CONTENTS
CONTENTS
Table of Contents
CONTENTS � � � � � � � � � � � � � � � � � � � � 2
Introduction� � � � � � � � � � � � � � � � � � � � � 3
Installation Principles � � � � � � � � � � � � � � � � � � � � � �3
System Components � � � � � � � � � � � � � 3
Recommended Tools � � � � � � � � � � � � � 5
Installation Diagram � � � � � � � � � � � � � � 6
ECU Installation � � � � � � � � � � � � � � � � � 7
Selecting a Mounting Location� � � � � � � � � � � � � � �7
Installing the ECU� � � � � � � � � � � � � � � � � � � � � � � � �7
ECU Installation Requirements� � � � � � � � � � � � � � �8
Installing Power & Interface
Components � � � � � � � � � � � � � � � � � � � � 9
Installing the harness � � � � � � � � � � � � � � � � � � � � � �9
Connecting the Driver Button � � � � � � � � � � � � � � �10
Connecting the Remote Control Receiver � � � � � 11
Installing Video Components � � � � � � 11
Installing the harness � � � � � � � � � � � � � � � � � � � � � 11
Mounting the Monitor � � � � � � � � � � � � � � � � � � � � �12
Connecting the Monitor � � � � � � � � � � � � � � � � � � �13
Monitor Settings � � � � � � � � � � � � � � � � � � � � � � � � �14
Assembling the Cameras � � � � � � � � � � � � � � � � � �15
Soft-Mounting Cameras � � � � � � � � � � � � � � � � � � �16
Installing the Cameras � � � � � � � � � � � � � � � � � � � �16
Determining Camera Locations � � � � � � � � � � � � �17
Hard-Mounting Cameras � � � � � � � � � � � � � � � � � � 19
Test and Calibrate� � � � � � � � � � � � � � � � � � � � � � � �20
Support Information � � � � � � � � � � � � � 24
Contacting FRC (Fire Research Corporation) � � 24
Warranty � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �24
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 3
inView 360 Fusion Installation Guide Introduction
Introduction
This guide describes how to install and use the inView 360-Fusion Around Vehicle Monitoring (AVM) system� inView
360-Fusion provides drivers with a real-time, 360-degree picture of the area around their vehicle to eliminate blind spots,
help improve pedestrian safety, prevent vehicle damage, and avoid liability costs�
Installation Principles
Installation of the inView 360 Around Vehicle Monitoring system is for certied personnel only. For more information on
the certication process, please contact the FRC Service Team (please see the back of this guide for details).
The installation process involves drilling into the exterior of a vehicle to mount cameras� Ensure you read this document
carefully, and verify the correct mounting locations prior to drilling�
System Components
The inView 360-Fusion installation package contains the following components:
1x ECU (Electronic Control Unit)
1x ECU Mounting
Bracket w/ 4x Screws
Electronic Control Unit (ECU) Components
NOTE: The installed system will not operate correctly until it has been calibrated. For more information,
see the inView 360 Calibration Guide included in the Calibration Kit.
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 4
inView 360 Fusion Installation Guide Introduction
Power & Interface Components
Video Components
1x Power & Interface Harness
2x In-line Fuses
(1A & 3A)
1x Reverse Signal Wire
1x Left (Orange) & 1x Right
(Brown) Signal Wires
1x Button Extension Cable & 1x Driver Button
1x Video Harness
4x Camera Extension Cables
4x Camera Mounting Kits (Each
kit incl. 1x Cover, 1x Bracket,
2x Camera Screws, 2x Bracket
Screws
2x Video Output Extension Cables
4x Cameras
4x Drilling Templates & 8x Screw Covers
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 5
inView 360 Fusion Installation Guide Recommended Tools
Monitor Components
1x Monitor
1x Monitor
Base
1x Monitor
Adhesive Pad
Video Cable
(attached to
monitor)
1x Remote
(NOT USED)
Recommended Tools
The following is a list of recommended tools for installing the inView 360-Fusion:
• Multimeter
• Electrical tape
• Soldering iron and solder
• Cordless Drill
• Phillips screwdrivers
• Phillips drill attachments
• Wire cutters
• Zip ties
• 1/8”, 1/16” Drill bits
• 3/4” Stepbit (Unibit)
• Crimpers
• Wire sh tape
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 6
inView 360 Fusion Installation Guide Installation Diagram
Installation Diagram
The inView 360-Fusion comes with two main connection harnesses, one for Power & Interface, and one for Video�
The following diagram provides a breakdown of each.
POWER & INTERFACEVIDEO
MCU UPDATECPU UPDATE
Power & Interface
Video
VBAT
GND
ACC
+3A Fuse
+1A Fuse
TOUCH
FLASHER
SPEAKER
OBD
IrDA
BUTTON
VOUT
GEAR
CVBS2
CVBS1
REAR CAM
DVR
FRONT CAM
RIGHT CAM
LEFT CAM
• VBAT - Yellow - Battery
• GND - Black - Ground
• VOUT - White - Not Used
• GEAR - Blue - Reverse
Signal
• ACC - Red - Ignition
• TOUCH - Not Used
• OBD - Not Used
• IrDA - Remote Control Sensor
• Flasher - Orange (Left), Brown
(Right) Signal
• BUTTON - Driver Button
• SPEAKER - Not Used
• CVBS1 - Monitor
• CVBS2 - DVR
• DVR - Not Used
Power & Interface Harness Legend Video Harness Legend
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 7
inView 360 Fusion Installation Guide ECU Installation
ECU Installation
Selecting a Mounting Location
The inView 360-Fusion ECU needs to be installed in a dry, covered location with easy access to the SD card port�
Here are a few idea locations for mounting the ECU in a vehicle:
Installing the ECU
Once you’ve determined your ECU mounting location, you’re ready to install it in the vehicle�
1� Place the ECU and mounting bracket in position. The bracket can be mounted on either side of the ECU.
2� Mark your drill positions.
3� Drill the screw holes�
4� Mount the ECU and bracket .
SD Card Slot
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 8
inView 360 Fusion Installation Guide ECU Installation
ECU Installation Requirements
Ventilation
• Install the ECU away from any sort of heat outlet, heater, or AC blower�
• Do not operate the ECU in a closed-in area or restrict ventilation in any way� The ECU requires air circulation to
maintain optimum operating temperature and provide best performance�
• Do not expose the ECU to moisture�
Secure Surfaces
• Do not mount the ECU to a plastic panel or other surface that cannot support the ECU’s weight or is subject to
constant vibration�
Mounting Orientation
• The ECU can be installed horizontally, vertically, or upside down�
Clearance Around the ECU and (optional) DVR
• Allow sufcient clearance: at least 6” in front of the ECU and 2” on each side for removal of the security front
cover and easy access to the hard drive and USB ports�
• Allow sufcient clearance behind the DVR for power, signal, and camera cables.
Power, Signal & Camera Cables
• Provide enough slack on the power cable to prevent any force from being exerted on the connectors.
• A single 4-inch diameter loop is sufcient.
• Avoid right angle bends in the Ethernet cables�
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 9
inView 360 Fusion Installation Guide Installing Power & Interface Components
Installing Power & Interface Components
Installing the harness
The Power & Interface harness connects the ECU to the vehicle’s power, ignition, ground, and directional signals (left,
right, reverse)� In addition, the harness provides power to the AVM’s remote control sensor and driver button�
To install the harness properly:
• Connect the GND (Black) wire to an appropriate vehicle ground source.
• Connect the VBAT (Yellow) wire to the vehicle’s constant power source via the 3A fuse�
• Connect the ACC (Red) wire to the vehicle’s ignition source via the 1A fuse�
ACC w/1A FuseVBAT w/3A Fuse
© Safe Fleet | September 2018 | All rights reserved
Document #: XE-SNB1-Install-PM-R0A
p. 10
inView 360 Fusion Installation Guide Installing Power & Interface Components
• Connect the GEAR (Blue) wire to the vehicle’s reverse signal source (via extension wire)� This source must be
positive (12v when the vehicle is put in reverse)�
• Connect the FLASHER connector (via extension cable) to the vehicle’s front turn signal sources (Orange for left,
Brown for right)� These sources must also be positive (12V when the left or right turn signals are on)�
Connecting the Driver Button
The Driver Button lets the operator switch between the front, rear, left, and right camera views on the in-cab monitor�
To install the driver button:
1� Choose a location in the vehicle� Ideally, the location should be within arm’s reach of the driver�
2� Drill a 7/16” hole�
3� Thread the button through the hole�
4� Tighten the nut to the underside of the button�
5� Connect the button to the extension cable�
6� Run the extension cable to the ECU�
7� Connect the extension cable to the BUTTON connector on the Power & Interface harness�
Tabla de contenidos
Otros manuales de Electrónica del automóvil de FRC
