Foxconn K7S741MG Hoja de datos
1
Easy Installation Guide
P/N:91-185-U41-M0-0E
Remark:
The above motherboard layout is provided for reference only;
please refer to the physical motherboard.
K7S741MG/K7S741GXMG Layout
ATXPowerConnector
ATA66/100/133
IDEConnectors
CD_INConnector
FDD ConnectorSYS FAN
Connector
FrontPanel
Connector
S/PDIF_OUT Connector
(optional)
184-pinDIMMSlots
CPU FAN Connector
IRConnector(optional)
462-pinCPU Socket
SiS741/741GXChipset
USB2.0Connector
FrontAudio Connector
8X/4XAGPSlot
PCIExpansionSlots
Clear CMOS Jumper
SiS963LChipset
BIOS-ProtectionJumper
(optional)
SPEAKER
Connector
2
K7S741MG/K7S741GXMG Rear Panel
PS/2 Mouse Connector
This green 6-pin connector is for a PS/2 mouse.
PS/2 Keyboard Connector
This purple 6-pin connector is for a PS/2 keyboard.
Serial Port (COM1)
This 9-pin COM1 port is for pointing devices or other serial devices.
Parallel Port (Printer Port)
This 25-pin port connects a parallel printer, a scanner, or other devices.
VGAConnector
The VGA connector is for output to a VGA-compatible device.
USB 2.0 Ports
These four Universal Serial Bus (USB) ports are available for connecting USB 2.0
devices.
LAN Connector
This port allows connection to a Local Area Network (LAN) through a network hub.
Line-in jack, Line-out jack, Microphone jack
Use the three audio ports to connect audio devices. The Line-in jack is for a tape
player or other audio sources. The Line-out jack is for a headphone or a speaker.
The Microphone jack is for a microphone. In 6-Channel mode, the function of the
three jacks becomes Rear Speaker Out, Front Speaker Out and Center/Subwoofer
Speaker respectively.
1
2
5
8
3
4
6
7
Serial Port
(COM1) VGAConnector USB2.0Portx4
PS/2Mouse
Connector
ParallelPort
(Printer Port) LANConnector
1
2
4
6
5
7
PS/2 Keyboard
Connector
3
Line-injack
Line-outjack 8
Microphone
jack
3
K7S741MG/K7S741GXMG Motherboard (x1)
WinFast Utility CD (x1)
Easy Installation Guide (x1)
IDE Ribbon Cable (x1)
FDD Ribbon Cable (x1)
I/O Shield (x1)
CPU:
K7S741MG:
Supports AMD K7 Duron, Athlon, Athlon XP
Supports 266/333/400 MHz FSB
K7S741GXMG:
Supports AMD K7 Duron, Athlon, Athlon XP
Supports 266/333 MHz FSB
Memory:
K7S741MG:
Supports PC3200/PC2700/PC2100
Supports 64/128/256/512 Mb technology up to 2 GB
K7S741GXMG:
Supports PC2700/PC2100
Supports 64/128/256/512 Mb technology up to 2 GB
Accessory Checklist
1. Support CPU & Memory
4
You can clear CMOS to restore default system setting. To clear the CMOS, follow
the procedures described below.
1. Turn off the AC power supply and connect pin 1 and 2 together using the jumper
cap .
2. Return the jumper setting to normal (pin2 and 3 together with the jumper cap).
3. Turn the AC power supply back on.
If the jumper FWH_EN set as “Disable” (pin2 & pin3), the system BIOS is protected
from being attacked by a serious virus, such as the CIH virus. You will be unable to
flash the BIOS to the motherboard when the system BIOS is protected.
3. BIOS-Protection Jumper (optional): FWH_EN
Normal (Default)
Clear CMOS
1
1
CLS_CMOS
1
1
Flash write
Disable
Flash Write
Enable
(Default)
FWH_EN
2. Clear CMOS Jumper: CLS_CMOS
5
Attach the power LED, IDE LED, reset switch and power switch connectors to the
corresponding pins.
4. Front Panel Connector: FP1
Plug the CPU cooling fan cable into the 3-pin CPU FAN power supply on the mainboard.
Connect the case cooling fan connector to FAN1.
5. CPU FAN & FAN1
CPU_FAN
GND
+12V
SENSE 1
FAN1
FP1
1 +
-
NC
HDLED
RESET
PLED
PSWITCH
+
-
SENSE +12V GND
1
6
The connector supports wireless transmitting and receiving device. Before using
this function, configure the settings of IR Mode from the “Integrated Peripherals”
section of the CMOS Setup.
The USB header is available for additional USB port if the USB ports on the rear
panel are inadequate. Compared to traditional USB 1.1 with the speed of 12Mbps,
USB 2.0 has a fancy speed up to 480Mbps, which allows faster Internet connection,
interactive gaming, and simutaneous running of high-speed peripherals.
7. USB Header: F_USB1
6. IrDA Header (optional): IR
+5V
GND
IRRX
IRTX
Empty
IR
1
F_USB1
D0+
D0-
VCC VCC
D1-
D1+
Empty
GND GND
NC
9 10
1 2
7
CD_IN is Sony standard CD audio connector, it can be connected to a CD-ROM
drive through a CD audio cable.
The audio interface provides two kinds of audio output choices: the Front Audio,
the Rear Audio. Their priority is sequenced from high to low (Front Audio to Rear
Audio). If headphones are plugged into the front panel of the chassis (using the
Front Audio), then the Line-out (Rear Audio) on the rear panel will not work. If you
do not want to use the Front Audio, pin 5 and 6, pin 9 and 10 must be SHORT, and
then the signal will be sent to the rear audio port.
8. CD_IN Connector: CD_IN
F_AUDIO
MIC_IN MIC_GND
MIC_PWR +5VA
AUD_OUT_R AUD_RET_R
NC Empty
AUD_OUT_L AUD_RET_L
12
910
CD_IN
CD_L
GND
CD_R 1
9. Front Audio Connector: F_AUDIO
8
The speaker connector is used to connect speaker of the chassis.
The S/PDIF out connector is capable of providing digital audio to external speak-
ers or compressed AC3 data to an external Dolby digital decoder.
VCC3
SPDIF_OUT
GND
Empty
1
SPDIF_OUT
10. Speaker Connector: SPEAKER
11. S/PDIF_Out Connector (optional): SPDIF_OUT
SPK NC SPKJ
Empty
1
SPEAKER
9
After you finish the setting of jumpers and connect correct cables, power on the
system and press <Del> during POST (Power On Self Test) to enter the BIOS Setup
Utility. Choose “Load Optimized Defaults” for recommended optimal performance.
Please make sure your system components are good enough for optimized defaults.
The motherboard is equipped with the Realtek ALC655 chip, which provides sup-
port for 6-channel audio output, including 2 front, 2 rear, 1 center and 1 subwoofer
channel. ALC655 allows the board to attach 4 or 6 speakers for a better surround
sound effect. To apply this function, you have to install the audio driver in utility CD
as well as an audio application supporting 5.1 Channel. Picture bellow repre-
sents the standard location of all speakers in 5.1 Channel sound track.
12. 5.1 Channel Audio Effects
Front
Left Front
Right
RearLeft Rear Right
Center
Blue
Green
Red
Subwoofer
13. Power on and Load Optimized Defaults
Select this option
and press <Enter>.
10
This motherboard comes with one Utility CD. To begin using the CD, simply insert
the CD disc into the CD-ROM drive. The CD will automatically bring up the main
menu screen. Click “Install Driver”, then click the relevant button to install IDE
Driver, AGP Driver, VGA Driver, DirectX 9.0b, USB2.0 Driver, Audio Driver and LAN
Driver from this CD.
Follow the screen order to
install the motherboard
drivers.
14. WinFast Utility CD
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Placa madre de Foxconn
Foxconn
Foxconn H67A-S Manual de usuario
Foxconn
Foxconn G45MG Series Manual de usuario
Foxconn
Foxconn A74ML Series Manual de usuario
Foxconn
Foxconn H67S Series Manual de usuario
Foxconn
Foxconn 720AX Manual de usuario
Foxconn
Foxconn K8M890M2MA Manual de usuario
Foxconn
Foxconn 661MXPro Hoja de datos
Foxconn
Foxconn C51XEM2AA Manual de usuario
Foxconn
Foxconn Q57M Series Manual de usuario
Foxconn
Foxconn G31 MX series Manual de usuario
Foxconn
Foxconn A88GM Deluxe Manual de usuario
Foxconn
Foxconn A7GMX-K Manual de usuario
Foxconn
Foxconn H55M-S Manual de usuario
Foxconn
Foxconn ELA Manual de usuario
Foxconn
Foxconn A6GMV Series Manual de usuario
Foxconn
Foxconn 755FXK8AA series Manual de usuario
Foxconn
Foxconn 6497MB Series Manual de usuario
Foxconn
Foxconn 45CMV series Manual de usuario
Foxconn
Foxconn P35AX-S Manual de usuario
Foxconn
Foxconn G31S Guía del usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
