Follett Horizon Elite series Manual de usuario
Order parts online
www.follettice.com
Horizon Elite™Ice Machine Models with RIDE®Technology
Installation Instructions for Ice Manager™Diverter Valve
HCD/HCF1810RMS, HCD/HCF2110RMS
HCD1810NMS, HCD2110NMS
(See model number congurator on page 2 for details.)
01157924R01
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Ice Manager
Diverter Valve
(1) Horizon™
Chewblet®Ice Machine
(purchased separately)
(2) ice storage units
(purchased separately)
Any combination of bins or dispensers
Ice Manager
Control Panel
Lane 1
Lane 2
remote condensing
2remote condensing ICE MANAGER
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
425 up to
425 lbs
(193 kg)
710 up to
675 lbs
(306 kg)
1010 up to
1061 lbs
(482 kg)
1410 up to
1466 lbs
(665 kg)
1810 up to
1790 lbs
(812 kg)
2110 up to
2039 lbs
(925 kg)
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
P Cornelius Profile
PR150
CondenserSeriesVoltageIcemaker
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
MC Maestro™
Chewblet®
(425 Series)
HC Horizon
Chewblet
(710, 1010,
1410, 1810,
2110 Series)
HM Horizon
Micro Chewblet
HC 1810D SVA
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
Chewblet®Ice Machine Model Number Configurations
3
ICE MANAGER remote condensing
Front cover
7
Internal connection
6
External connection
5
Louvered docking assembly
3
Site preparation
2
Unpack
1
After thorough review of Ice Manager site survey, read and complete
Horizon ice machine installation sections 1 through 6.
For connection to Ice Manager diverter valve system
refer to Ice Manager installation guide.
Horizon ice machine for use with Ice Manager diverter valve system
The Ice Manager diverter valve system delivers ice to two ice storage units enabling a single Follett
Horizon ice machine to meet demand for ice at two locations. The system’s sensors monitor ice levels
in each storage unit and automatically switch ice delivery to the appropriate location.
Ice transport tube
4
4remote condensing ICE MANAGER
Carefully unpack and inspect the contents of your Follett ice machine. 1
Unpack
7/16"
7/16"
➊➋➌
➍➎
➏➐
DO NOT TILT ICE MACHINE
TO ACCESS BOLTS!
COMPRESSOR DAMAGE
WILL RESULT
Unpack ice machine
1. 1
5
ICE MANAGER remote condensing
Prepare the installation site. 2
Site preparation
2.1
Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.
Electrical ➊
• 120/60/1-5 amps
Potable water supply ➋ (3/8” push-in internal connection, 3/8” OD tubing required)
• 10-70 psi (69-483kpa)
• 45-90 F (7-32 C)
• Follett recommends the use of an in-line water ltration system (item# 00130286)
• This equipment is to be installed with adequate backow protection to comply with applicable
federal, state, and local codes
Drain ➌ (3/4” Barb)
• Minimum 8” radius on silicone drain line. Drain line from the ice machine must have at least
1/4” per foot pitch (6,4mm/0,3m).
Refrigeration lines ➍
• 7/8” ∅ (22,4 mm) suction line 1810/2110(insulated) ➍
• 3/8” ∅ (9,5 mm) liquid line ➎
Installation site requirements
➎
➍
3/8" ∅ (9,5mm)
NEMA
5-15
➋
➊
➋
7/8" ∅ (22,4mm)
1" PVC Drain
2 ft. x 1" OD
silicone tubing 3/4" MPT x 1" slip
3/4" barb x 3/4" FPT
➌
1'
➌
1/4" per foot
(6,4 mm per 0,3 m)
2.1
6remote condensing ICE MANAGER
Install the louvered docking assembly.
Louvered docking assembly 3
➊
➊
3/8˝ ∅
high pressure
line
7/8" ∅ low pressure line
2" (50,8 mm)
Stub Typ
1.81" (46 mm)
3.75" (95.3 mm)
2" (50,8 mm)
➋
• Mount louvered docking assembly ➊
• “Rough-in” the refrigerant piping ➋
2.1 Louvered docking assembly
3.1
Machine stand accessory
Wall bracket accessory
• Mount louvered docking assembly to wall
bracket accessory
• Mount louvered docking assembly to
machine stand accessory
Prior to installing the louvered docking assembly, ensure that the
drain tting is oriented (right or left) correctly for your installation.
An optional straight drain tting is also supplied. You may need to
remove the back panel of the docking assembly in order to re-orient
or change the drain tting. Replace back panel prior to mounting the
docking assembly.
BEFORE PROCEEDING
7
ICE MANAGER remote condensing
No Lip
➋
Access panel/
door on counter
3.25" (83 mm) min.
➊
➌
24" min.
(609 mm
22.25" min.
(656 mm)
CROSSBRACE
Top View
DOCKING STATION
• Prior to installing the louvered docking assembly, ensure that the drain tting is oriented (right
or left) correctly for your installation. An optional straight drain tting is also supplied. You may
need to remove the back panel of the docking assembly in order to re-orient or change the
drain tting. Replace back panel prior to mounting the docking assembly.
• Position and screw louvered docking assembly to the bottom of counter inside of access panel/
door min. of 3.25” (83 mm) from the front edge of the cross brace ➊
• The mounting surface for the louvered docking assembly must be solid.
Do not mount directly onto runners or channels.
• There must be no lip or edge that would hinder the ice machine from sliding in or out of the
louvered docking station ➋
• Ice machine must be installed facing forward as shown for service accessibility ➌
Undercounter installation requirements
4.2
8remote condensing ICE MANAGER
Ice transport tube
Install the ice transport tube. 4
1/4"
1'
➍
➏
➐
➊
➋
➌
➎
Hot Water
160 F (71 C)
Ice transport tube tips
• Insulate entire length of ice transport tube ➊
• Secure ice transport tube ➋as needed to prevent dips and traps from forming.
For long tube runs see guide on page 15.
• Pitch ice transport tube at least 1/4" per foot (6,4mm/.3m) ➌
• Ice transport tube must drain towards ice machine
Ice transport tube to Ice machine
• Be sure tube ends are square ➍
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➎
before making connection to ease assembly
• Push ice transport tube onto ice machine nipple ➏
• Install hose clamp ➐
Ice transport tube installation.
4.2
9
ICE MANAGER remote condensing
Connect utilities to louvered docking assembly. 5
External connections
CAUTION
• Plug must be accessible after nal installation.
Refrigerant
5.2
➊
• Braze supplied quick-connect lines onto
stub-ins ➊.
3/4" barb x 3/4" FPT
1" Stand pipe/Drain
2 ft. x 1" OD
silicone tubing
Minimum 8"
radius
➍
3/4" MPT x 1" slip
➎
➌
➋
➊
➏
• Rough-in ice machine potable water
supply ➊.
3/8” push-in connection will be made at
shut-off valve inside machine
• Remove access panel if necessary ➋.
• Connect the silicone tubing to the ice
machine 3/4” drain barb ➌.
• Assemble the 3/4” barb x 3/4” FPT to the
3/4” MPT x 1” slip. Connect the other end
of the silicone tubing to the 3/4” barb ➍.
• Connect the 1” slip tting to the 1” stand
pipe/drain ➎.
Note: Minimum 8” radius on silicone
drain line. Drain line from the ice machine
must have at least 1/4” per foot pitch
(6,4mm/0,3m).
• Apply Petrol-gel to barbed drain tting ➏
• Replace access panel.
Water and drain
5.1
10 remote condensing ICE MANAGER
Connect louvered docking assembly to ice machine. 6
Internal connections
Refrigeration lines
6.3
• Slide ice machine into louvered docking
assembly ensuring that drain tube is fully
seated on barbed drain tting ➊
• Insert ice transport tube all the way into
coupling and tighten nut rmly ➋
Ice transport tube installation
6.1
• Insert potable water line into valve ➊
Water line
6.2
• Remove twist tie
• Carefully pass cord thru opening and plug
into wall outlet
Power cord
6.4
• Evacuate line set.
• Connect self-sealing liquid and suction
line ttings ➊
➊
➋
➊
➊
Otros manuales para Horizon Elite series
3
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Máquina de hielo de Follett
Follett
Follett Horizon Elite Chewblet HCD1010RMS Manual de usuario
Follett
Follett Ice Pro EDB1000-SA Series Manual de usuario
Follett
Follett HCE1400A Manual de operación
Follett
Follett H_C700AHS Manual de usuario
Follett
Follett Horizon Elite 1010 Series Manual de usuario
Follett
Follett D400A/W Manual
Follett
Follett Horizon Elite Chewblet H D710ABS Series Manual de usuario
Follett
Follett MCC425A/W S Manual de operación
Follett
Follett Horizon Elite Chewblet 1010 Series Manual de usuario
Follett
Follett Horizon Elite Chewblet 1010 Series Manual de usuario
Follett
Follett HCD700R Manual de operación
Follett
Follett HCC1000AHS Manual de usuario
Follett
Follett MCE414A S Series Guía de configuración
Follett
Follett Maestro Plus MCD425WBS Manual de usuario
Follett
Follett Maestro Manual de usuario
Follett
Follett HCC1000ABS Manual de usuario
Follett
Follett C33984 Manual de operación
Follett
Follett Horizon Elite Chewblet HCD1410RBT Manual de usuario
Follett
Follett 7FS100A Guía de configuración
Follett
Follett Horizon Elite HCD1010RHT Manual de usuario
