FLIR Quasar CM-6405 Manual de usuario

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

Quasar™ Mini-Dome

CM-6405/CM-6408

Quick Install Guide

1 Check Contents

Make sure all of the items above are included in the camera kit.

2 Select a Location

Select a suitable location to mount the camera.

Cables can enter the camera either through the rear of the camera via the

mounting bracket or through a conduit hole on the side of the camera. If the cables

enter through the rear, make sure that the location provides a suitable method for

routing the cables.

Verify that the operating temperature range is in the following ranges, with no

more than 90% non-condensing humidity:

With heater: -55° C to 60° C (-67° F to 140° F)

Cold start with heater: -55° C to 60° C (-67° F to 140° F)

Warnings

Placing a camera in a surrounding environment subject to extremely high

temperature can result in an explosion or the leakage of flammable liquid or

gas.

Subjecting the camera to extremely low air pressure can result in an explosion

or the leakage of flammable liquid or gas.

For further advice on positioning and orienting the camera, see the camera's

installation and user guide.

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

3 Power Supply Options

The camera can be powered by:

A UL-listed L.P.S. (Limited Power Supply) unit, rated to a maximum temperature

of 60° C:

o12 VDC, 1.21A minimum

o24 VAC, 50/60Hz, 1.2A minimum

PoE (Power over Ethernet): 48 VDC, 0.27A minimum

For assistance with purchasing a power supply, contact your FLIR representative.

4 Configure the Camera

FLIR recommends configuring the camera before mounting and aiming it. It is also

possible to configure the camera after mounting it, which could be more

appropriate for certain installations. For the camera's default Video Configuration

settings, see 7 Default Video Configuration Settings.

4.1 Install the FLIR DNA tool

The FLIR Discovery Network Assistant (DNA) tool does not require a license to

use and it is free. Download it from the product's web page at FLIR.com >

Products > Security > Visible Security Cameras to a computer on the same VLAN

to which you will connect the camera. Then, unzip the file.

4.2 Remove Cover and Separate Base

Tip

When unpacking the camera, do not remove the plastic sheet protecting the

dome.

To remove the dome cover:

a. Using the Torx wrench, loosen the screw on the camera's outer circular ring

that secures the dome cover to the camera base.

b. While firmly holding the base, rotate the ring counterclockwise to loosen it.

c. Carefully pull the ring and cover away from the base.

Outer Ring Locking Screw

Loosen Ring

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

To separate the camera base from the mounting bracket:

a. Using a screwdriver, loosen the two twist-lock screws securing the camera and

its base to the mounting bracket.

b. Gently pull the camera and its base away from the mounting bracket.

Separate Base from Bracket

Change the number of LEDs (optional)

The camera has a total of eight IR illumination LEDs. On the 3D lens assembly,

there is a 4 / 8 (default) switch that determines the number of enabled IR LEDs.

With the dome cover removed, you can change the switch setting.

4.3 Connect the Camera

Connectors

Connector

Connection

RJ-45

Two LEDs

Attach a Cat 6 cable from the network switch to the RJ45 connector for a

10/100/1000 Mbps Ethernet and IEEE 802.3af class 0 PoE connection.

Ethernet is required for streaming video and for configuring the camera.

The green link LED indicates a good network connection. The orange

activity LED flashes to indicate network activity.

Warning

The PoE unit and all interconnected equipment must be installed indoors within the same

building, including all PoE-powered network connections, as described by Environment A

of the IEEE 802.3af standard.

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

Connector

Connection

Four-pin

power

terminal

block

24VAC -

12VDC -

If using a 24VAC or 12VDC power

supply, connect it to the power

terminal block connector according

to the pin assignment shown.

24VAC +

12VDC +

Warning

The power cord to the 12 VDC or 24 VAC power supply unit must be connected to a

socket outlet with an earthing connector.

Default

Button

To restore the camera to its factory defaults, use a proper tool to press

the default button for at least 20 seconds.

USB

Connects to Wi-Fi dongle (future release support)

microSD

Card Slot

For video clip and snapshot recording and file storage, insert a

microSD / SDHC / SDXC card (up to 512 GB, Class 10) in the card slot.

When the camera is powered on, do not remove the microSD card.

Nine-pin

terminal

block

Audio In L

Alarm Out +

Attach wires from external devices

to the terminal block connector for

alarm and audio in/out according to

the pin assignment shown.

Audio In R

GND

Alarm In +

Audio Out L

Audio Out R

Warning

Do not connect an external power supply to the nine-pin audio/alarm I/O terminal block

connector.

Warning

This product contains a battery that is soldered to the PCB. There is a risk of

explosion if the battery is replaced by an incorrect type. Do not replace the

battery. The battery should be disposed of in accordance with the battery

manufacturer’s instructions.

Tip

To make it easier to mount and install the camera, while the camera is on the

bench or in the lab, you can connect Ethernet and other cable patch cords to the

camera's connectors and route them through the grommets on the base and

through the mounting bracket. Then, you'll be able to mount and install the

camera without separating the camera base from the mounting bracket a second

time.

4.4 Configure for Networking

You can configure the camera using the DNA tool, the camera's web page, or a

supported VMS.

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

DNA tool

Camera's web page

Discover camera IP address

•

Configure IP address, mask, and gateway

•

Configure DNS settings, MTU, and Ethernet speed

•

Change user credentials

•

Change video format

•

Configure more than one camera at the same time

•

For information about using the camera's web page to configure the camera, see

the camera's installation and user guide. For information about using a supported

VMS to configure the camera, see the VMS documentation.

By default, DHCP is enabled on the camera and a DHCP server on the network

assigns the camera an IP address. For example, if the camera is managed by

FLIR's Horizon or Meridian VMS and the VMS is configured as a DHCP server, the

VMS automatically assigns the camera an IP address.

If the camera is managed by FLIR’s Latitude VMS or is on a network with static IP

addressing, you can manually specify the camera’s IP address using the DNA tool

or the camera's web page. The camera's default IP address is 192.168.0.250.

To manually specify the camera's IP address using the DNA tool:

a. Make sure the camera and the PC are on the same LAN segment.

b. Run the DNA tool (DNA.exe) by double-clicking .

The Discover List

appears, showing

compatible

devices on the

LAN segment and

their current IP

addresses.

In the DNA Discover List, verify that the camera's status is Online.

If this is the first time you are configuring the camera or if it is the first time after

resetting the camera to its factory defaults, DNA automatically authenticates

the camera with the default password for the camera's admin user (admin).

If the admin user password has been changed, you need to authenticate the

camera.

In the DNA Discover List, right-click the camera and select Login.

In the DNA - Login window, type the password for the admin user. If you do

not know the admin user password, contact the person who configured the

camera's users and passwords.

Click Login, wait for Ok status to appear, and then click Close.

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

In the DNA Discover List, verify that the camera's status is Authenticated.

c. Change the camera’s IP address.

Right-click the camera and select IP Setup.

In the DNA - IP Setup window, clear Use

DHCP and specify the camera's IP

address. You can also specify the Mask

(default: 255.255.255.0) and Gateway.

Then, click Update, wait for Ok status

to appear, and then click Close.

4.5 Change Video Format (Optional)

By default, NTSC is the camera's video format.

To change the camera's video format to

PAL using the DNA tool:

a. In the DNA Discover List, right-click the

camera and select Change Video Format.

b. In the Change Video Format window,

select PAL.

c. Click Update, wait for Ok status to

appear, and then click Close.

For more information about using the DNA tool to configure one or more cameras,

see the DNA User Guide. While the software is open, click the Help icon

4.6 Re-attach Dome Cover

To prevent damaging the camera's internal components while moving it from the

bench or lab to its mounting location, re-attach the dome cover to the base and

then remove it again at the mounting location.

Before doing so, you can re-attach the camera base to the mounting bracket. Use

a screwdriver to tighten the two twist-lock screws securing the camera and its

base to the mounting bracket. If you do not re-attach the camera base to the

mounting bracket, remember to bring the screwdriver to the mounting location.

To re-attach the dome cover:

a. Using the two guide pins on the dome cover and the triangles on the cover and

on the base, carefully align and position the dome cover onto the base.

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

b. Securely tighten the outer ring.

c. Lock the ring. Using the Torx wrench, tighten the screw on the outer ring that

secures the cover to the base.

5 Install the Camera

Warning

The camera must be installed by qualified personnel and the installation should

conform to all local codes.

Be sure to have the required accessories and tools available and refer to the

camera's installation and user guide as necessary.

5.1 Fit Mounting Hardware

If required, install the mounting hardware for the camera according to the

instructions for the hardware.

5.2 Remove Cover and Separate Base

Repeat the steps described in 4.2 Remove Cover and Separate Base.

5.3 Install Mounting Bracket

You can install the mounting bracket on standard electrical boxes or directly on a

secure, flush, and vibration-free surface.

To install the mounting bracket on a

standard electrical box:

Attach the bracket to the box using:

The holes in the mounting bracket,

according to the types of boxes engraved on

the bracket

The corresponding holes in the box

Suitable bolts, washers, and nuts (not

included in the camera kit)

To install the mounting bracket directly on

a surface:

a. Choose four widely spaced mounting holes on the bracket for optimum flat

surface mounting.

b. Using the bracket as a template to mark the surface, drill four anchor holes.

c. (Optional) If necessary, drill a hole wide enough for routing cables.

d. Hammer the four plastic screw anchors into the drilled holes.

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

e. Insert the anchors and then attach the bracket to the surface using the four M4

25mm self-tapping screws included in the camera kit.

When tightening the screws, the holes in the mounting plate allow for making small

adjustments to the bracket's position.

5.4 Route Cables and Connect the Camera

Cables can enter the camera

from the side or from the rear.

To route cables through the side of the camera:

a. Use the Torx wrench to loosen the screw securing the side conduit hole cover

and remove the hole cover.

b. Route cables through the hole.

To route cables through the rear of the

camera:

a. For each cable, use the Torx wrench to punch

a hole in the center of the rubber glands in the

the camera's base, from the underside.

b. Route cables through the hole in the mounting

bracket and through the holes in the grommet.

c. Push the cables back through the seal so that

the seal extends out of the base.

Inside base

Connect the camera according to the information in 4.3 Connect the Camera.

Note

Connect the camera to a 24VAC or PoE power source as the primary power

source, and then connect 12VDC as the secondary power source. If the primary

power source fails, the camera seamlessly switches to 12VDC until the primary

power source is restored.

5.5 Mount and Aim the Camera

a. Make sure that the camera is facing the required field of view. Then, carefully

re-attach the camera base to the mounting bracket. Use a screwdriver to

tighten the two twist-lock screws securing the camera and its base to the

mounting bracket.

b. Aim the camera, which has three axes for adjusting the field of view:

oPan adjustment – Rotate the lens base until satisfied with the field of view.

oTilt adjustment – Loosen the screw locking the camera lens in its tilt angle. Tilt

the lens until satisfied with the field of view. Then, tighten the screw.

oLens rotation – Rotate the 3D assembly in the lens until satisfied with the field

of view.

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

Aiming the Camera

Caution

Do not rotate or tilt beyond the mechanical limits for each axis:

Pan adjustment range: 356°

Tilt adjustment range: ±80°

Lens rotation range: ±98° – Rotating the 3D assembly in the lens beyond its

mechanical limit can twist, disconnect, or break the camera's internal cables.

c. Repeat the steps described in 4.6 Re-attach Dome Cover.

6 Complete Camera Setup

Specify the camera's zoom and focus, and format the microSD card, using the

camera's web page. FLIR recommends using Microsoft Internet Explorer 11.0,

with the ActiveX plug-in. The camera's web page supports other browsers that do

not support ActiveX. However, using another browser requires configuring MJPEG

encoding for at least one of the camera's video streams; for more information, see

the camera's installation and user guide.

a. Log in to the camera’s web page.

In the DNA Discover List, double-

click the camera.

In the Windows Security dialog

box, type a user name and

password. Both are case-

sensitive.

When logging in to the camera's web

page for the first time or for the first

time after resetting the camera to its

factory defaults, type admin for the user

name and for the password.

Then, specify a new password for the

admin user. Use a strong password

consisting of at least eight characters

and at least one uppercase letter, one

lowercase letter, and one number.

Passwords can include the following

special characters: |@#~!$&<>+_-.,*?=

Log back in using the new password.

CM-6405/CM-6408 QIG Rev 110

January 2021

This document does not contain any export-controlled information.

b. If the User Account Control dialog opens and prompts you to install the

install.cab file, click Yes.

If ActiveX installation is not successful, in the

Internet Explorer Tools > Internet Options >

Advanced Security settings, select Allow software

to run or install even if the signature is invalid and

click OK. Try installing ActiveX again. After a

successful ActiveX installation, uncheck the

checkbox, and click OK.

If a popup message appears for running the ActiveX add-on, click Allow.

c. Install the web player.

Note

If you have previously installed a web player application on the PC, you

should delete the existing web player from the PC before accessing the

camera. For information on how to install the new player, uninstall a previous

player, and clear temporary Internet files, see the camera's installation and

user guide.

The camera's web page opens.

d. On the Live page, adjust the zoom or focus using the controls.

b. Format the microSD card.

From the navigation bar, click Settings.Then, in the sidebar, click System >

Edge Recording > SD Card.

Otros manuales para Quasar CM-6405

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara digital de FLIR

FLIR

FLIR ZENMUSE XT2 Manual de usuario

FLIR

FLIR USB3 Vision Flea3 Manual de usuario

FLIR

FLIR Elara DX Series Manual de usuario

FLIR

FLIR FC S Series Instrucciones de montaje

FLIR

FLIR Txxx series Manual de usuario

FLIR

FLIR X-Series Manual de usuario

FLIR

FLIR Exx series Manual de usuario

FLIR

FLIR Exx series Manual de usuario

FLIR

FLIR A400 Series Manual de usuario

FLIR

FLIR M-Series Manual de usuario

FLIR

FLIR MPX C233BD Manual de usuario

FLIR

FLIR A6 Series Manual de usuario

FLIR

FLIR Quasar Gen III CP-6302 Series Manual de usuario

FLIR

FLIR GRASSHOPPER 3 Series Manual de uso y cuidado

FLIR

FLIR ThermaCAM QuickView Manual de usuario

FLIR

FLIR FIREFLY Manual de usuario

FLIR

FLIR Exx series Manual de usuario

FLIR

FLIR Ariel CM-3102 Manual

FLIR

FLIR Tau Camera TAU-0035-00-10 Manual de usuario

FLIR

FLIR Scout Bi-Ocular Manual de usuario

FLIR

FLIR Scout Bi-Ocular Manual de usuario

FLIR

FLIR LADYBUG 5 USB3 Manual de usuario

FLIR

FLIR 310 Series Manual de usuario

FLIR

FLIR Lorex LW3211-C Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario