Flash 384A Manual de usuario

384A DMX CONTROLLER

384ch 2019

User Manual

Instrukcja Obsługi

F9000383

User Manual •Instrukcja Obsługi

IMPORTANT!

Do not point strong light output from other fixtures

at the 384A DMX CONTROLLER 384ch 2019, as

intense illumination can damaged the parts.

2. SAFETY INFORMATION

1. INTRODUCTION

THANK YOU FOR PURCHASING 384A DMX CONTROLLER 384ch 2019. FOR SAFETY

REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ

THE INSTRUCTIONS.

WARNING!

Figure 2.

Shield or shade the head if necessary.

Please keep this User Manual for future

      

another user, be sure that they also receive

this instruction booklet.

Unpack and check carefully there is no

transportation damage before using the



Before operating, ensure that the voltage

and frequency of power supply match the



It’s important to ground the yellow/green

conductor to earth in order to avoid electric

shock.

Disconnect main power before servicing

and maintenance.





only, but always by taking its base.

Maximum ambient temperature is: 40

Don’t operate it where the temperature is

higher than this.

In the event of serious operating problem,

     



carried out by unskilled people can lead to

damage or malfunction. Please contact the

nearest authorized technical assistance

center. Always use the same type spare

parts.

Do not connect the device to any dimmer

pack.

Do not touch any wire during operation

and there might be a hazard of electric

shock.

To prevent or reduce the risk of electrical



rain or moisture.



visibly damaged.

384A DMX CONTROLLER 384ch 2019 •Art No F9000383

4. INSTALLATION

3. PRODUCT INFORMATION

Power supply voltage: 90-240V,

Power Input: DC9-12V, 500 mA

Dimension [cm]: H-7,3 W-52,2 D-18,3

DMX 512/1990 Standard

Controls 24 inteligent lights of up to 16

channels totally 384 channels.

30 banks, each witch 8 scenes, 6 chase,

each witch up to 240 scenes.

Records up to 6 chases with fade time and

speeds.

Weight [kg]: 3kg

Type of packaging: Carton Box

Make sure all necessary cables are

properly connected. Always ensure that



and slipping while operating. Always

ensure that the structure to which you

are attaching the unit is secure and is

able to support a weight of 10 times of

the unit’s weight. Also always use a safety

cable that can hold 12 times of the weight







of the touch of people and has no one pass

by or under it.

4.1 Voltage specification

3.1 Main Features

Input Voltage Total Power Frequency

90-240V 2W 50/60Hz

16 sliders for direct control of channels

MIDI control over banks, chases and

blackout.

Bulit-in microphone for music mode

Auto mode program controlled by fade

time sliders

DMX in/out: 3 pin XLR

LED gooseneck lamp

             

             

banks can contain up to 240 steps composed of the saved scenes and in any order. Programs

can be triggered by music, midi,automatically or manually. All chases can be executed at

the same time.



a wheel and LED display indicators for easier navigation of controls and menu functions.



wheel at the same time by means of a programmable wheel.



156

7816

18 17

10 11 12

13 14 15

5. OPERATION

2422 25

5.1 Product Overview (FRONT)

5.2 Product Overview (REAR PANEL)

User Manual •Instrukcja Obsługi

Item Button or Fader Function

1Scanner select button Fixture Selection

2Scanner indicators LEDS Indicates the xtures currently selected

3Scene select button universal bump button representing scene Location

for storage and selection

4Channel faders

For adjusting DMX values, Ch 1-16 can be adjusted

immediately after pressing the respective scanner

Select button

5Program button Used to enter programming mode

6Music/Bank Copy button Used to activate Music mode and as the copy Com-

mand during programming

7LED display window status window display pertinent operational data

8Mode indicator LEDS Provides operating mode status, (manual, Music or

auto)

9Bank Up button Function button to traverse Scene/Steps in Banks

or chases

10 Bank Down button Function button to traverse Scene/Steps in Banks

or chases

11 Tap display button Sets the chase speed by tapping, and toggles

between Values and percentages.

12 Blackout button Sets the shutter or dimmer value of all xtures to

„0” causing all light Output to case

13 Midi/ADD button Activates MIDI external control and also used to

conrm the record/save process

14 Auto/Del button Used to acivated Auto mode and as the delete func-

tion key during programming

15 Chaser buttons Chase memory 1-6

16 Speed fader This will adjust the hold time of a scene or a step

Within a chase

17 Fade-time fader Also considered a cross-fade, sets the interval Time

between pages of control

18 Page Select button In manual mode, press to toggle between pages of

control

21 MIDI input port For external triggering of Banks and Chases using a

MIDI device

22 DMX output connector DMX control signal

23 DC input jack Main power feed

24 USB lamp socket

25 ON/OFF power Switch Turns the controller on and off

384A DMX CONTROLLER 384ch 2019 •Art No F9000383

Common Terms

      

intelligent light programming.

Blackout is a state by where all lighting

        

usually on a temporary basis.

DMX-512 is an industry standard

digital communication protocol used in

entertainment lighting equipment. For

more information read Sections „DMX

Primer” and „DMX Control Mode” in the

Appendix.

Fixture refers to your lighting instrument

or other device such as a fogger or dimmer

of which you can control.

Programs are a bunch of scenes stacked



either a single scene or multiple scenes in

sequence.

Scenes are static lighting states.

Sliders also known as faders.

Chases can also be called programs. A chase

consists of a bunch of scenes stacked one



Scanner refers to a lighting instrument

with a pan and tilt mirror; however, in

the I LS-CON controller it can be used to

control any DMX-512 compatible device as



MIDI is a standard for representing musical

information in a digital format. A MIDI

input would provide external triggering

of scenes using midi device such as a midi

keyboard.

Stand Alone      

to function independently of an external

controller and usually in sync to music, due

to a built in microphone.

Fade slider is used to adjust the time

between scenes within a chase.

Speed    

scene will hold its state. It is also considered

a wait time.

Shutter is a mechanical device in the



        

intensity of the light output and to strobe.

Patching refers to the process of assigning



SETTING UP THE SYSTEM

1) Plug the AC to DC power supply to the

system back panel and to the mains outlet.

2) Plug in your DMX cable(s) to your

intelligent lighting as described in the

     

Primer on DMX see the „DMX Primer”

section in the Appendix of this manual.

FIXTURE ADDRESSING

     

   

       

corresponding apart.

„SCANNER” buttons on the unit, must be

spaced 16 channels.

Fixture or

Scanner #

Default DMX

Starting

Address

Binary Dipswitch

settings switch to

the „On Position”

1 1 1

2 17 1, 5

3 33 1, 6

4 49 1, 5, 6

5 65 1, 7

6 81 1, 5, 7

7 97 1, 6, 7

8 113 1, 5, 6, 7

9 129 1, 8

10 145 1, 5, 8

11 161 1, 6, 8

12 177 1, 5, 6, 8

User Manual •Instrukcja Obsługi

13 193 1, 7, 8

14 209 1, 5, 7, 8

15 225 1, 6, 7, 8

16 241 1, 5, 6, 7, 8

17 257 1, 9

18 273 1, 5, 9

19 289 1, 6, 9

20 305 1, 5, 6, 9

21 321 1, 7, 9

22 337 1, 5, 7, 9

23 353 1, 6, 7, 9

     

manual for DMX addressing instructions.

       



WHEEL ASSIGNMENT



are alike or share the same control

attributes, the DMX-240A allows the user

to assign the wheel the correct pan and

     

including 16 bit channel assignments. It

also allows the user to re-assign physical



user can combine or unify control of similar

     





Action:

1) press and hold the PROGRAM button

until the led blinks

2) Press and hold FINE & MODE buttons

together

3) times to access the channel assignment





dmx channel.

3) press a SCANNER button that represents



tilt

4) Use the BANKUP/DOWN buttons to

select pan/tilt

Notes:

All wheels can be reassigned to output on a



Press AUTO/DEL&MODE buttons together

to delete the channel assignment mode.



Action:

5) Press the TAP/DISPLAY button to switch

pages

6) Press and hold MODE button, then

press the SCENES buttons to select the

DMXchannel. AII LEDs will blink.

7) Press and hold FINE & MODE buttons to

exit

Notes:

You can re-assign the DMX channel to all

controller fader channels.



Review wheel assignment or reverse

Action: (Reverse Review)

1) Press and hold FINE & MODE buttons

together to access the wheel assignment

mode

2) press a SCANNER button to select a

scanner

3) Press and hold FINE & MODE buttons

together (2) times to exit



Action: (wheel assignment Review)

1) Press and hold FINE & mode buttons

together (2) times to access the channel

reverse mode

2) press a SCANNER button to select a

scanner

3) Press and hold FINE & MODE buttons to

exit

COPY SCANNER

Example: Copying Scanner 1 into Scanner 2

384A DMX CONTROLLER 384ch 2019 •Art No F9000383

Action:

1) Press and hold SCANNER button # 1.

2) While holding button# 1 press SCANNER

button # 2.



releasing SCANNER button # 2.





Notes:

To save time, you can copy the settings of

one Scanner button to another.



REVERSE CHANNEL OUTPUT

Action:

1) press and hold the PROGRAM button

until the led blinks

2) Press and hold FINE & MODE buttons

together to access the channel assignment

mode ,then press the SCANNER button

3) Use the Bankup/Down buttons to select

pan/tilt

4) Press the TAP/DISPLAY button to switch

between pages

5) press and hold MODE button, then press

the SCENES buttons to select the DMX

channel. AII LEDs will blink.

6) Press and hold FINE & MODE buttons (2)

times to exit

Notes:

You can permanently reverse the output of

any given channel on the controller.

Press AUTO/DEL&MODE buttons together

to delete the reverse channel.

FADE TIME ASSIGN

You can choose whether the boards fade

timeduringsceneexecutionisimplemented

broadly to all output channels or only to





and colors to change quickly while not



Action:

1) Turn OFF the controller.

2) Hold the MODE and TAP DISPLAY

buttons simultaneously.

3) Turn ON the controller.

4) Press the TAP DISPLAY button to toggle

between the two modes. Either ALL CH (all

channels) or ONLY X/Y (Pan & Tilt only)

5) Press MODE and TAP DISPLAY to save



Notes:

ALL CH: All channels ONLY X/Y: Only Pan

& Tilt

Operation

MANUAL MODE

      

all scanners. You are able to move them

and change attributes by using the channel

faders and wheel.



Action:

1) Press the AUTO DEL button repeatedly

until the MANUAL LED is lit.

2) Select a SCANNER button.



attributes. PAGE/SELECT A/8 button:

Use to switch between fader control of

(A: Ch 1-8 ), (B: Ch 9-16)

TAP DISPLAY button:

Press to toggle the output indicator on the

LCD display between DMX values (0-255)

and percentage (0-100)

Notes:

All changes made while in Manual Mode are

temporary and will not be recorded

REVIEW SCENE OR CHASE

     

already recorded scenes and chases on the

User Manual •Instrukcja Obsługi

controller. Other wise skip section and go to

programming.

Action: (SCENE Review)

1) Select any one of the 30 banks by pressing

the BANK UP/DOWN buttons.

2) Select a SCENE button (1-8) to review.



attributes.

Action: (CHASE Review)

1) Press any one of the 6 CHASE buttons.

2) Press the TAP DISPLAY button to view

the step number on the display.

3) Press the BANK UP/DOWN buttons

review all scenes in the chase.

Notes:

Make sure you are still in MANUAL Mode.



Programming



scenes (or steps) that will be called up

      

programs can be created of 8 scenes in each.

ENTERING PROGRAM MODE

1) Press the Program button until the LED

blinks.

CREATE A SCENE

A scene is a static lighting state. Scenes

       

memories on the controller and each bank



can save 240 scenes total.

Action:

1) Press the PROGRAM button until the

LED blinks.

2) Position SPEED and FADE TIME sliders

all the way down.

3) Select the SCANNERS you wish to include

in your scene.

4) Compose a look by moving the sliders

and wheel.

5) Tap MIDI/REG button.

6) Choose a BANK (01-30) to change if

necessary.

7) Select a SCENES button to store.

8) Repeat steps 3 through 7 as necessary.

8 scenes can be recorded in a Program.

9) To exit program mode, hold the

PROGRAM button.

Notes:

Deselect Blackout if LED is lit.



You can access channels 9~16 by pressing



       

control.



       

display will now indicate the Scene number

and Bank number used.

Tip! Press the FINE button, activate

joystick or slider by moving it then use the

Bank Up/Down buttons to change values in

increments of „1” .

Shortcut:Press[PROGRAM]+[SCANNERS]

Adjust[Faders& Wheel]+[BANK]+[SCENE]

+Press [PROGRAM] to store.

RUNNING A PROGRAM

Action:

1) Use BANK UP/DOWN buttons to change

Program banks if necessary.

2) Press the AUTO DEL button repeatedly

until the AUTO LED turns on.

3) Adjust the PROGRAM speed via the

SPEED fader and the loop rate via the FADE

TIME fader.

4) Alternatively you can tap the TAP

     

384A DMX CONTROLLER 384ch 2019 •Art No F9000383

two taps sets the time between SCENES (up

to 10 minutes).

Notes:

Deselect Blackout if LED is lit.

Also called a Tap-Sync.

CHECK PROGRAM

Action:

1) Press and hold the PROGRAM button

until the LED blinks.

2) Use the BANK UP/DOWN buttons to

select the PROGRAM bank to review.

3) Press the SCENES buttons to review each

scene individually.

EDITING A PROGRAM



Action:

1) Press and hold the PROGRAM button

until the LED blinks.

2) Use BANK UP/DOWN buttons to change

Program banks if necessary.

      

SCANNERS button.

      

using the channel faders and wheel.

5) Press the MIDI/REC button to prepare

the save.

6) Select the desired SCENES button to

save.

Notes:

Deselect Blackout if LED is lit.

COPY A PROGRAM

Action:

1) Press and hold the PROGRAM button

until the LED blinks.

2) Use BANK UP/DOWN buttons to select

the PROGRAM bank you will copy.

3) Press the MIDI/REC button to prepare

the copy.

4) Use BANK UP/DOWN buttons to select

the destination PROGRAM bank.

5) Press the MUSIC BANK COPY button to

execute the copy. All LEDs on the controller

will blink.

Notes:

All 8 scenes in a Program bank will be

copied.

Chase Programming

A chase is created by using previously

created scenes. Scenes become steps in a

chase and can be arranged in any order

you choose. It is highly recommended that

      

time; you delete all chases from memory.

See „Delete All Chases” for instructions.

CREATE A CHASE

A Chase can contain 240 scenes as steps.

      

interchangeably.

Action:

1) Press the PROGRAM button until the

LED blinks.

2) Press the CHASE (1-6) button you wish

to program.

3) Change BANK if necessary to locate a

scene.

4) Select the SCENE to insert.

5) Tap the MIDI/REC button to store.

6) Repeat steps 3-5 to add additional

steps in the chase. Up to 240 steps can be

recorded.

7) Press and hold the PROGRAM button to

save the chase.

RUNNING A CHASE

Action:

1) Press a CHASE button then press the

AUTO DEL button.

2) Adjust the Chase speed by tapping the

TAP DISPLAY button twice at a rate of your

choosing.

User Manual •Instrukcja Obsługi

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de DJ de Flash

Flash

Flash F7100499 Manual de usuario

Flash

Flash F7100310 Manual de usuario

Flash

Flash F7100503 Manual de usuario

Flash

Flash F7000643 Manual de usuario

Flash

Flash F7000251 Manual de usuario

Flash

Flash Spyder 3-HEAD Manual de usuario

Flash

Flash F7100086 Manual de usuario

Flash

Flash F7100305 Manual de usuario

Flash

Flash F7000542 Manual de usuario

Flash

Flash F7200177 Manual de usuario

Flash

Flash P7200045 Manual de usuario

Flash

Flash BEAM Moving Head 15R Manual de usuario

Flash

Flash MOVING HEAD BEAM 17R Manual de usuario

Flash

Flash Virtuoso 420 Manual de usuario

Flash

Flash F7300248 Manual de usuario

Flash

Flash F71000269 Manual de usuario

Flash

Flash F1000510 Manual de usuario

Flash

Flash F7100315 Manual de usuario

Flash

Flash F7100077 Manual de usuario

Flash

Flash F7100545 Manual de usuario

Flash

Flash F7300249 Manual de usuario

Flash

Flash LED MOONTH FLOWER LIGHT Manual de usuario

Flash

Flash F7100514 Manual de usuario

Flash

Flash F7000048B Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario