Fimer PVS-166-TL-US Manual de usuario

Solar Inverter

PVS-166-175-TL-US A.2 Version

Quick Installation Guide

In addition to what is explained in this quick installation guide, the safety and installation information provided in the product manual must be read and

followed. The technical documentation for the product is available at the website.

The device must be used in the manner described in the manual. If this is not the case the safety devices guaranteed by the inverter might be

ineffective.

ATTENTION –AIMPORTANT SAFETY INSTRUCTIONS

This document contains important safety instructions that must be followed during the installation and maintenance of the equipment.

ATTENTION –ASAVE THESE INSTRUCTIONS

Keep this document in a safe place near the inverter for easy access during installation, operation and maintenance.

ATTENTION –AThe installer must read this document in its entirety before installing or commissioning this equipment. In addition to

what is explained below, the safety and installation information provided in the product manual must be read and followed. For more

detailed information regarding proper installation and use of this product, refer to the product manual located at www.fimer.com.

ATTENTION –AThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference

(2) this device must accept any interference received, including interference that may cause undesired operation.

ATTENTION –AAll pictures and illustrations shown in this document are indicative and must be intended as support for installation

instruction only. Actual product may vary due to product enhancement. Specifications subject to change without notice. The latest

version of this document is available on the FIMER website www.fimer.com.

Table of Content

1. Reference number index 5

1.1 PVS-166/175-TL-US - External view 6

1.2 PVS-166/175-TL-US - External sides view 7

1.3 PVS-166/175-TL-US Power module- Internal view 7

1.4 PVS-166/175-TL-US Wiring box- Internal view 8

1.5 Communication board 9

2. Labels and Symbols 10

3. Models and range of equipment 12

4. Lifting and transport 12

4.1 Transport and handling 12

4.2 Unpacking and checking 12

4.3 Lifting 12

5. List of supplied components 15

6. Kit of recommended spare parts 15

7. Choice of installation location 16

7.1 General recommendation on installation position 16

7.2 Tilting allowance 16

7.3 Distances 17

7.4 Installation of multiple units 17

7.5 Wireless signal environmental checks 18

8. Mounting Instructions 18

8.1 Installations of protection covers for wiring box openings 18

8.2 Bracket assembly 18

8.3 Assembly of the Inverterto the bracket 19

8.4 Opening the Wiring box cover 20

8.5 Final fastening operations 21

8.6 Opening the power module box cover 22

8.7 Connection of the AC interface power cables (25) 22

8.8 Connection of the interface signal connectors 23

8.9 Connection of the DC and AFD interface cables 23

9. Routing the cable to the inverter 25

10. Installation planning 25

10.1 Characteristics of the protective grounding cable 25

10.2 Load protection breaker (AC disconnect switch) and differential protection

downstream of the inverter 25

10.3 Characteristics and sizing of the line cable 26

11. Grid output connection (AC side) 26

12. Checking the correct polarity of the strings and Input

connection (DC) 27

12.1 Input connection with DC cable tray (60) 28

12.2 Input connection without DC cable tray (60) 29

13. Connection of the communication and control signals 30

13.1 Communication and control board (28) references 30

13.2 Connections to the communication and control board 31

13.3 Ethernet connection 31

13.4 Connection of RS-485 serial communication line 32

13.5 Slave mode 32

13.5.1 Master mode 32

13.6 Remote control connection 33

13.7 Multifunction Relay connection (ALARM and AUX) 33

14. Description of LED panel 34

15. Commissioning 36

15.1 Commissioning via FIMER Installer for Solar Inverters mobile APP 36

15.2 Commissioning via Web User Interface 37

16. Arc fault detection 37

17. Grid support functions and Voltage & Frequency trip limits 38

18. Characteristics and technical data 39

18.1 Technical data 39

1. Reference number index

Inverter external view

01 Power module

02 Wiring box

03 Mounting bracket

04 Handles

05 Cover quarter cam locks

06 Side latch

07 Wiring box front cover

08 LEDs panel

09 AC disconnect switch (-SX2 only)

10 EGC connection point

11 AC opening (size 3” conduit)

12 Service opening (size 3/4” conduit)

13 Service opening (size 1/2” conduit)

14 Rear pins for bracket assembly

15 Cover support brackets

16 DC disconnect switches

17 DC input quick fit connectors

18 DC and ARC fault interface cables

19 ARC fault connector

20 Junction screws

21 DC surge arrester plate

22 AC connection busbar

23 AC overvoltage surge arresters

24 Interface signal cables

25 AC interface power board

26 Interface Protective Earth connection point

27 AC protective shield

28 Communication and control board

Inverter external view

29 DC interface connection point

31 Interface signal connector

32 AC interface power cable

33 Alarm terminal block

34 RS485 FIMER service 120Ohm termination res.

35 DRM0 activation switch

36 RS485 line 120Ohm termination res.

37 FIMER RS485 service RJ45 connector (service only)

38 Remote ON/OFF terminal block

39 RS485 line terminal block

40 Ethernet connector 1 (RJ45)

41 Ethernet connector 2 (RJ45)

42 USB connector

44 CR2032 coin battery

45 Memory board

46 RS485 line communication board

50 Power module front cover

51 Cooling section (top side)

52 Cooling section (left side)

53 Internal fan

54 Cable duct

55 Protective earth connection point

56 RS-485&Rem.ON/OFF external connector (Service only)

57 AFD reset button

58 AC interface connections protective cover

59 AFD interface cable

60 DC cable tray

1.1 PVS-166/175-TL-US - External view

01 51

Version with DC cable tray

1.2 PVS-166/175-TL-US - External sides view

14 06

03 15

16 17

1.3 PVS-166/175-TL-US Power module- Internal view

Version with protective cover

Version without protective cover

1.4 PVS-166/175-TL-US Wiring box- Internal view

1.5 Communication board

J9 J10

S1 S3

2. Labels and Symbols

The labels on the inverter and on wiring box have the Agency marking, main technical data and identification of the equipment and

manufacturer.

ATTENTION –AThe technical data shown in this quick installation guide does not replace that shown on the labels attached to the

equipment.

The labels on the power module and on the wiring box have the Agency marking, main technical data and identification of the equipment

and manufacture

NOTE –DThe labels shown below have to be intended as example only.

FORBIDDEN –HThe labels affixed to the equipment must NOT be removed, damaged, stained, hidden, etc., for any reason

whatsoever.

Power module

Wiring Box

Fimer S.p.A.

Via Tortona, 25 - I 20144 Milano (MI)

A. Inverter/wiring box model

B. Power module/wiring box Part Number

C. Power module/wiring box Serial Number

D. Powe Week/Year of manufacture

E. Main technical data

F. Certification marks

NOTE –DAn additional PN and SN label of the full system (power module + wiring box) is applied on the external packaging. This

label should be stored in plant documentation for reference.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de Fimer

Fimer

Fimer UNO-DM-3.3-TL-PLUS-US-SB-RA-Q Manual de usuario

Fimer

Fimer UNO-DM-COM KIT Manual de usuario

Fimer

Fimer PVS-166-175-TL-US Manual de usuario

Fimer

Fimer PVS-50-TL Manual de usuario

Fimer

Fimer TRIO-20.0-27.6-TL-OUTD-US Manual de usuario

Fimer

Fimer PVS-50.0 Manual de usuario

Fimer

Fimer PVS980-58 Manual de usuario

Fimer

Fimer Series R25-R55 Manual de usuario

Fimer

Fimer MEGASTATION Manual de usuario

Fimer

Fimer PVS-20-TL Manual de usuario

Fimer

Fimer UNO-DM-1.2 Manual de usuario

Fimer

Fimer UNO-DM-6.0-TL-PLUS-US-Q Manual de usuario

Fimer

Fimer PVS-60-TL-US Manual de usuario

Fimer

Fimer PVS-12.5-TL Manual de usuario

Fimer

Fimer TRIO-5.8-TL-OUTD-400 Manual de usuario

Fimer

Fimer PVS-175-TL Manual de usuario

Fimer

Fimer UNO-DM 1.2-TL-PLUS-Q Manual de usuario

Fimer

Fimer UNO-DM-6.0-TL-PLUS-Q Manual de usuario

Fimer

Fimer PVS-60-TL-US Manual de usuario

Fimer

Fimer VSN300 Manual de usuario

Fimer

Fimer PVS-100-TL Manual de usuario

Fimer

Fimer T 422 Manual de usuario

Fimer

Fimer PVS-30-TL Manual de usuario

Fimer

Fimer PVS-166-TL US Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario