Fayat Group BOMAG BF 800 C Manual de usuario

Service - Manual

Catalogue number.

008 917 73 02/2013

BF 800 C

Road Finisher

S/N 821 837 17 1001 ....

S/N 821 837 71 1001 ....

S/N 821 837 19 1001 ....

S/N 821 837 66 1001 ....

S/N 861 893 50 1001 ....

S/N 861 893 60 1001 ....

Find manuals at https://best-manuals.com

Table of Contents

BOMAG 3008 917 73

General 9

1.1 Introduction 10

1.2 Safety regulations 11

1.3 General repair instructions 15

1.4 Tightening torques 27

Technical data 31

2.1 Technical data 32

Maintenance 39

3.1 General notes on maintenance 40

3.2 Fuels and lubricants 41

3.3 Table of fuels and lubricants 44

3.4 Running-in instructions 45

3.5 Maintenance table 46

E-Plan wiring diagrams 49

4.1 Understanding E-Plan circuit diagrams 50

4.2 Circuit symbols in E-Plan 59

4.3 Identification of switch blocks in the wiring diagram 62

4.4 Designation of components in the wiring diagram 63

4.5 Terminal designations in wiring diagram 64

Engine 67

5.1 Diesel engine 68

5.2 Engine description TCD 2012 69

5.3 Lubrication oil circuit TCD 2012 / 2013 71

5.4 Coolant circuit TCD 2012 / 2013 72

5.5 Fuel system TCD 2012 / 2013 73

5.6 Deutz Common Rail (DCR) injection system for TCD 2012 / 2013 75

5.7 Exhaust gas recirculation TCD 2012 / 2013 79

5.8 Wastegate - charge pressure controller on TCD-engines 80

5.9 Engine problems 82

5.10 Checking the engine oil level 85

5.11 Changing engine oil and oil filter cartridge 85

5.12 Replacing the fuel pre-filter cartridge, bleed the fuel system 86

5.13 Replace the fuel filter 88

5.14 Check, clean the water separator 89

5.15 Check the coolant level 90

5.16 Replace the coolant 90

5.17 Checking the thermostat in disassembled state 91

5.18 Air filter maintenance 92

5.19 Clean the cooling fins on engine and hydraulic oil cooler 94

5.20 Intercooler, drain off oil and condensation water 95

5.21 Adjust the valve clearance 95

5.22 Checking the ribbed V-belt, replacing if necessary 96

5.23 Replace the crank case ventilation valve 97

5.24 Engine conservation 98

5.25 Special tools, Deutz engine (TCD 2012 2V) 99

Engine electrics 115

Find manuals at https://best-manuals.com

Table of Contents

BOMAG4008 917 73

6.1 EMR3 system components 116

6.2 Deutz EMR 3 - engine connections 121

6.3 Pin assignment of engine control EDC16 / EMR3 122

6.4 Rotary speed sensor for camshaft 127

6.5 Crankshaft speed sensor 128

6.6 Rail pressure sensor 129

6.7 Fuel pressure sensor 130

6.8 Fuel control unit 132

6.9 Injector 133

6.10 Oil pressure sensor 134

6.11 Sensor for charge air temperature and charge air pressure 136

6.12 EMR coolant temperature sensor 138

6.13 Glow plugs 140

6.14 Sensor, water in fuel 140

6.15 Air filter vacuum switch 141

6.16 Float switch, coolant tank 142

6.17 Charge control light, engine RPM-meter 143

6.18 Diagnose with SERDIA 144

6.19 Diagnose with CAN-bus 147

6.20 Diagnostics interface 148

6.21 EMR3 List of fault codes 150

6.22 Generator 221

6.23 Replacing the voltage regulator 230

6.24 Electric starter 232

Electrics 239

7.1 Service the battery, check the main battery switch 240

7.2 Starting the engine with jump leads 241

7.3 Starting with jump wires 241

7.4 Fuses 242

7.5 Fuse assignment 243

7.6 Component overview - Electrics 246

7.7 Overview of wiring looms 254

7.8 Control elements 267

7.9 View of control panel 268

7.10 Instrument cluster 270

7.11 Data collector 272

7.12 View of external operator stations 276

7.13 View of external operator stations 277

7.14 View of screed control panel 278

7.15 View of electric heating control panel 279

7.16 Functional block diagram overview of functions, complete 280

7.17 Block diagram components on CAN 281

7.18 Block diagram CAN with control elements 282

7.19 Block diagram of travel circuit 283

7.20 Block diagram material feed 284

7.21 Block diagram screed 285

7.22 Block diagram screed heating 286

7.23 Functional block diagram monitoring functions 287

Find manuals at https://best-manuals.com

Table of Contents

BOMAG 5008 917 73

7.24 Block diagram Emergency Stop functions 288

7.25 Electronic control units 289

7.26 Checking the voltage supply for the control unit 291

7.27 Diagnostics concept 299

Error codes -- general information 303

8.1 Error codes - BF800 -- general information 304

Input codes 307

9.1 Input codes -- Display: Function and operation 308

9.2 Input codes -- automatic calibration of currents in the travel system 309

9.3 Input codes -- manual calibration of currents in the travel system 312

9.4 Input codes -- travel signal by push button for max. screed relief 315

9.5 Input codes -- Changing the type of speed potentiometer 317

9.6 Input codes -- Activating/deactivating the screed heat in low idle speed 318

9.7 Input codes -- activate/deactivate the cleaning function 319

9.8 Input codes -- Saving/loading TCU settings 320

9.9 Input codes -- Teaching L.C.S. Function 321

9.10 Input codes -- changing the tamper start and stop ramps 323

9.11 Input codes -- Changing the currents for the tamper pump 326

9.12 Input codes -- changing the tamper start and stop ramps 329

9.13 Input codes -- Changing the currents for the vibration pump 332

9.14 Input codes -- Saving/loading SCU settings 335

9.15 Input codes -- Restoring factory settings of the SCU 336

9.16 Input codes -- Activate/deactivate hydraulic front gate 337

9.17 Input codes -- Changing the currents in the auger pumps 338

9.18 Input codes -- Change the auger start / stop ramps 341

9.19 Input codes -- Changing the currents in the scraper belt pumps 344

9.20 Input codes -- Enable/disable lifting the auger block together with the screed

347

9.21 Input codes -- Saving/loading MCU settings 348

9.22 Input codes -- Restoring factory settings of the MCU 349

9.23 Input codes -- driving against the closed brake 350

9.24 Input codes -- showing logged errors 351

9.25 Input codes -- showing logged errors with operating hours 352

9.26 Input codes -- deleting the error log 353

Replacement of components 355

10.1 How to proceed when replacing components? 356

Material hopper, description 357

11.1 Material hopper and transport 358

Vibrating screed, description 365

12.1 Screed 366

Basic settings on the screed 371

13.1 Notes on the screed adjustment (type S500 & S600) 372

13.2 Bringing the straight crossfalls to zero position 373

13.3 Aligning basic screed and mobile sections 374

Assembling the screed extensions 377

14.1 Notes on assembling screed extensions 378

14.2 Assembling the screed extensions 381

Find manuals at https://best-manuals.com

Table of Contents

BOMAG6008 917 73

Electric screed heating, repair 393

15.1 Electric screed heating 394

15.2 Electric screed heating - commissioning 399

15.3 Faults in the electric heating 401

Travel drive, description 403

16.1 Travel system 404

Hydraulics 409

17.1 Hydraulic circuit 410

17.2 Component overview -- hydraulics 412

17.3 Description of travel pump 417

17.4 View of the machine 423

17.5 Pumps for: Scraper belt, augers, vibration & tampers 424

17.6 View of the machine 431

17.7 Description of fan pump 433

17.8 View of the machine 437

17.9 Description of charge pumps 438

17.10 Check the hydraulic oil level 440

17.11 Change hydraulic oil and hydraulic oil filter 441

Hydraulics - travel circuit 445

18.1 Description of driving 446

18.2 Description of brake circuit 448

Hydraulics - material transport 451

19.1 Description of scraper belts 452

19.2 Description of augers 453

19.3 Description tamping 454

19.4 Description vibration 455

Hydraulics - Service 457

20.1 Description of fan circuit 458

20.2 Description of Service (a) 459

20.3 Description of Service (b) 460

20.4 Description of Load Control System (LCS) 461

Tests and adjustments 463

21.1 Special tools, tests and adjustments 464

21.2 Checking and adjusting the vibration 468

21.3 Checking/adjusting tamping 475

21.4 Checking/adjusting the scraper belts 486

21.5 Checking/adjusting the augers 493

21.6 Checking & adjusting the service pump/cylinder functions 499

21.7 Checking & adjusting the time for screed levelling 503

21.8 Checking/adjusting the hopper wings 505

21.9 Checking/adjusting the mobile screed 507

Suppliers documentation 509

22.1 Travel pump 511

22.2 Travel motor 549

22.3 Service pump and fan pump 603

22.4 Pump scraper chains, augers, tamper, vibration 633

22.5 Travel gear 691

Find manuals at https://best-manuals.com

Table of Contents

BOMAG 7008 917 73

Circuit diagrams 761

23.1 Hydraulic diagram 763

23.2 Electric circuit diagrams 783

Find manuals at https://best-manuals.com

Table of Contents

BOMAG8008 917 73

Find manuals at https://best-manuals.com

BOMAG 9008 917 73

1 General

Find manuals at https://best-manuals.com

1.1 Introduction

BOMAG10 008 917 73

1.1 Introduction

This manual addresses the professionally qualified

personnel or the after sales service of BOMAG, and

should be of help and assistance in correct and effi-

cient repair and maintenance work.

This manual describes the disassembly, dismantling,

assembly, installation and repair of components and

assemblies. The repair of components and assem-

blies is only described as this makes sense under due

consideration of working means and spare parts sup-

ply.

Documentation

For the BOMAG machines described in this manual

the following documentation is additionally available:

1 Operating and maintenance instructions

2 Spare parts catalogue

3 Service information

4 Fundamental electrics

Use only genuine BOMAG spare parts.

Spare parts needed for repairs can be taken from the

spare parts catalogue for the machine.

This manual is not subject of an updating service; for

this reason we would like to draw your attention to our

additional "Technical Service Bulletins".

In case of a new release all necessary changes will be

included.

In the course of technical development we reserve the

right for technical modifications without prior notifica-

tion.

Information and illustrations in this manual must not

be reproduced and distributed, nor must they be used

for the purpose of competition. All rights according to

the copyright law remain expressly reserved.

!Danger

These safety regulations must be read and ap-

plied by every person involved in the repair /main-

tenance of this machine. The applicable accident

prevention instructions and the safety regulations

in the operating and maintenance instructions

must be additionally observed.

BOMAG GmbH

Printed in Germany

Find manuals at https://best-manuals.com

Otros manuales de Equipos de construcción de Fayat Group

Fayat Group

Fayat Group BOMAG BT 60 Manual de usuario

Fayat Group

Fayat Group BOMAG BC 573 RB-4 Manual de usuario

Fayat Group

Fayat Group BOMAG BF 700 C-2 Manual de usuario

Fayat Group

Fayat Group DYNAPAC CA5000 Manual de usuario

Fayat Group

Fayat Group BOMAG BM 1000/35 Manual de usuario

Fayat Group

Fayat Group DYNAPAC CC425 Manual de usuario

Fayat Group

Fayat Group BOMAG BW 174 APO-4i Manual de usuario

Fayat Group

Fayat Group Dynapac CA25 Manual de usuario

Fayat Group

Fayat Group BOMAG BW 226 DH-4i BVC Manual de usuario

Fayat Group

Fayat Group BOMAG BW 190/202 AD-5 Manual de usuario

Fayat Group

Fayat Group BOMAG BW177D-50 Instrucciones de uso

Fayat Group

Fayat Group Dynapac CA25 Manual de usuario

Fayat Group

Fayat Group BOMAG BW 28 RH Manual de usuario

Fayat Group

Fayat Group Dynapac F2500W Manual

Fayat Group

Fayat Group Dynapac CC900G Manual de usuario

Fayat Group

Fayat Group BOMAG BW 80 AD-5 Manual de usuario

Fayat Group

Fayat Group BOMAG BF 700 C S500 Manual de usuario

Fayat Group

Fayat Group BOMAG BMF 2500 M Manual de usuario

Fayat Group

Fayat Group BOMAG BW 202 AD-50 Manual de usuario

Fayat Group

Fayat Group BOMAG BM 500/15 Manual de usuario

Fayat Group

Fayat Group Bomag BW 138 AD-5 Instrucciones de uso

Fayat Group

Fayat Group BOMAG BW 80/90 AD-5 Manual de usuario

Fayat Group

Fayat Group BOMAG BC 573 RB-3 Manual de usuario

Fayat Group

Fayat Group BOMAG BF 800-P Series Manual de usuario

Manuales populares de Equipos de construcción de otras marcas

SASFORKS

SASFORKS EXTREME Manual de usuario

Hailo

Hailo H-50 Manual de usuario

Graco

Graco LineLazer ES 1000 Manual de uso y cuidado

Greenlee

Greenlee 555RSC Manual de usuario

Manitowoc

Manitowoc Grove CD3340B Manual de usuario

Lux Tools

Lux Tools A-FMR-20 Set Manual de usuario

SIP

SIP 03683 Manual de usuario

Volvo

Volvo L30G Manual de usuario

Grizzly

Grizzly G8712 Manual de usuario

Modulift

Modulift CMOD 12 Manual de usuario

Case

Case DV201 Manual de usuario

Sealey

Sealey SC10.V2 Manual de usuario

Wacker Neuson

Wacker Neuson DT05 Manual de usuario

HYVA

HYVA AMCO VEBA 81 Series Manual de usuario

Atlas Copco

Atlas Copco Dynapac V5100TV Manual de usuario

Toro

Toro 323 Manual de usuario

Manitowoc

Manitowoc National Crane 1400A Manual de usuario

SGS

SGS EC1500 Manual de usuario