Fanaway EVORA Manual de usuario
V1.0 –MUTI –Published on 11.2017
FANAWAY
EVORA RETRACTING BLADE
CEILING FAN
WITH IR REMOTE
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.
Fanaway Evora Installation Instructions
2 | P a g e
CONTENTS
GB
Installation instruction manual .......................................................................................... 3
D
Installationsanleitung ........................................................................................................14
F
Guide d’installation............................................................................................................24
E
Manual de instrucciones de instalación.............................................................................34
I
Manuale delle istruzioni di installazione............................................................................44
NL
Installatiehandleiding.........................................................................................................54
Fanaway Evora Installation Instructions
3 | P a g e
THANK YOU FOR PURCHASING
Thankyou for purchasing this qualityFanaway product. To ensure correct function and safety, please read
all instructions before using the product and keep the instructions for future reference.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the appliance in a safe way and
understand the hazards involved. Cleaning and maintenance shall not be undertaken by children
without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the appliance by a person responsible for their
safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means
for an all-pole disconnection incorporated in the fixed wiring in
Fanaway Evora Installation Instructions
4 | P a g e
accordance with the wiring rules.
Example: If a fan is connected to a circuit that can be isolated via an
all-pole safety switch at the switchboard, then this is considered to
be an all-pole disconnection to the ceiling fan electrical circuit,
meeting the requirements of clause 7.12.2 ofAS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the
same room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 30kg.
7. The fan should be mounted so that the blades are at least 2.3m above the floor in Europe or 2.1m
above the floor in Australia.
8. This fan is designed for indoor use only. Mounting the fan in a location where it is subject to water or
moisture is dangerous and will void the warranty.
9. Only a licensed electrician should execute the installation.
Fanaway Evora Installation Instructions
5 | P a g e
BEFORE INSTALLATION
Unpack the fan and carefully identify the parts. Please refer to Fig 1.
Fig. 1
Fanaway Evora Installation Instructions
6 | P a g e
1
Mounting bracket x 1
9
Blades x 4
2
Canopy screws x 4
10
Retraction mechanism x 1
3
Canopy x 1
11
Lamp base x 1
4
Down rod x 1
12
Cover x 1
5
Bolt & pin cover x 1
13
Screws for cover x 3
6
Bolt x 1
14
Lamp shade x 1
7
Pin x 1
15
Wood screws x 2
8
Top housing x 1
16
Remote receiver x 1
17
Remote hand set x 1
INSTALLING THE MOUNTING BRACKET
The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing from
the tip of the blade to the nearest objects or walls.
Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least
30kg, with the two long screws provided. Ensure at least 30mm of the screw is threaded into the
support.
NOTE: The bracket screws provided are for use with wooden structures only. For structures
other than wood, the appropriate screw type MUST be used.
Angled Ceiling Installation
This fan hanging system supports a maximum 15 degree angled
ceiling installation.
Fig. 2
Fig. 3
Fanaway Evora Installation Instructions
7 | P a g e
INSTALLING THE FAN
Installing the down rod
1) Feed the down rod (5) through the canopy (4) and the coupling cover (6).
2) Remove the ball joint by loosening the set screw (3), insert the plug (1) and the motor wires (2)
through the down rod then secure the ball joint back to the down rod.
3) Insert the down rod to the coupling (7), line up the coupling holes with the down rod holes and
insert the bolt (8). Then insert the pin (9) to the end of the bolt.
4) Finally secure the down rod and coupling by tightening the two set screws (10) on the coupling.
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the registration slot (A) of the hanger ball is
positioned on the stopper (B) of the mounting bracket (C) to prevent the fan from rotating when in
operation. (Fig.5)
Fig. 5
Fig. 4
Fanaway Evora Installation Instructions
8 | P a g e
LIGHT KIT INSTALLATION
1. Remove the lamp shade (5) from the lamp base (4) by turning it anti-clockwise.
2. Loosen the screw (1) from the base bracket (3). Align the two slot screws (2) with the keyhole slots
of the lamp base (4).
3. Turn the lamp base counterclockwise until the slot screws are firmly at the end of the slots.
4. Secure screw 1 back to the base bracket. Tighten all three screws. Do not over-tighten.
5. Connect the upper plug (9) from the fan to the lower plug (9) from the lamp base together.
6. Secure the wire protective cover (7) to lamp base by tightening the screws (8).
7. Install the globes (Not included) to the lamp holders (6)
8. Finally install the lamp shade (5) to the lamp base by turning it clockwise.
Fig. 6
Fanaway Evora Installation Instructions
9 | P a g e
ELECTRICAL WIRING DIAGRAM
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONALALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
Connect “LIVE”supply wire to the “L” of terminal block on the mounting bracket.
Connect “NEUTRAL” supply wire to the “N” of terminal block on the mounting bracket.
Connect “EARTH” wire to the “ ” of terminal block on the mouthing bracket.
Connect the output connector (1) from the receiver to the connector (1) from the fan body.
Connect the connector (2) from the fan mounting bracket to the input connector (2) from the
receiver.
Connect the connector (3) from from the infrared detecter to the input connector (3) from receiver.
Fig. 7
Fig. 6
Fanaway Evora Installation Instructions
10 | P a g e
FINISHING THE INSTALLATION
After completing the electrical connection at the mounting bracket terminal block, connect the ceiling
fan wiring via the quick connector plug.
Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy
and that the wires are not damaged during this step. Secure the canopy to the hanger bracket using
the screws provided. Fig. 8
USING YOUR CEILING FAN
REMOTE CONTROL
Your ceiling fan is controlled by the remote control. Before
operating the remote, the following must be considered.
-1 x CR2032 3V batteryis required tooperate the remote
control. Pull out the battery tray (2) by pressing the click
(1) of the battery tray. Place the battery (3) on the tray
and insert the tray back to remote hand set (4) indicated
by “+” polarity symbol (5). Ensure the polarity is correct
as shown in the battery compartment.
Fig. 8
Fig. 9
Tabla de contenidos
Idiomas:
Otros manuales de Admirador de Fanaway
Fanaway
Fanaway EVO1 - PREVAIL Guía de instalación
Fanaway
Fanaway CORBELLE Guía de instalación
Fanaway
Fanaway VEIL Manual del propietario
Fanaway
Fanaway CLASSIC Guía de instalación
Fanaway
Fanaway Classic LD-0003 16 01 Series Guía de instalación
Fanaway
Fanaway XIAO Manual de usuario
Fanaway
Fanaway LD-48 FAN IN Manual de usuario
Fanaway
Fanaway LED EVO1 Manual del propietario
Fanaway
Fanaway NEXUS Manual de usuario
Fanaway
Fanaway VEIL Manual de usuario
Fanaway
Fanaway CLASSIC Manual de usuario
Fanaway
Fanaway EVO1 - PREVAIL Manual de usuario
Fanaway
Fanaway EVO2 Manual de servicio
Fanaway
Fanaway ORBIT DC Manual del propietario
Fanaway
Fanaway Montclair Manual de usuario
Fanaway
Fanaway LD-0003-10/WH/GS/E27 Manual de servicio
Fanaway
Fanaway MYA Manual de usuario
Fanaway
Fanaway LED EVO1 Manual de usuario
Fanaway
Fanaway EVO1 - PREVAIL Manual de servicio
Fanaway
Fanaway LED EVO1 Manual de usuario
