Extron electronics FOX II T HD 4K Manual de usuario

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications bef

ore connecting the

oduct to the po

wer source.

FOX II T HD 4K • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate

the Extron FOX II T HD 4K Fiber Optic Transmitter. The transmitter is compatible with all Extron

FOX II receivers.

WARNING:The FOX II T HD 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution.

Plug the attached dust caps into the optical transceivers when the ber cable is unplugged.

CLASS 1 LASER PRODUCT, see the FOX II T HD 4K User Guide, at www.extron.com.

AVERTISSEMENT : Le FOX II T HD 4K émet une lumière invisible en continu (conforme à la classe1) qui peut être dangereux

pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque

le câble bre optique est débranché.

Produit laser de classe1, voir le FOX II T HD 4K User Guide sur www.extron.com (en anglais).

Installation

Step 1 — Mounting

FOX II T HD 4K Transmitter Rear Panel

100-240V ~ 0.5A MAX

50-60 Hz

HDMI LOOP THRU

LRRS-232

OPTICAL

RESET

LINK

RS-232 IR

ALARM

Tx Rx G1 2

Tx Rx Tx RxG

AUDIO

INPUTS AUDIO

RETURN OUT

REMOTE

OVER

FIBER

FOX T HD 4K

Turn off or disconnect all equipment power

sources and mount the transmitter as required.

For mounting details and considerations, see the

FOX II T HD 4K User Guide at www.extron.com.

Step 2 — Input and Output Connections

a. Connect an HDMI video source to the HDMI input connector.

HDMI LOOP THRU

b. If desired, connect an HDMI video display to the Loop-Thru connector for a local display.

c. Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector.

AUDIO

See the drawing below step 2d to make connections on the captive screw connector.

d. For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw connector.

AUDIO

RETURN OUT

See the drawing below to make connections on the captive screw connector.

ATTENTION:

• For unbalanced audio, connect the sleeves to the

ground contact. DO NOT connect the sleeves to the

negative (–) contacts.

• Pour l’audio asymétrique, connectez les manchons au

contact au sol. Ne PAS connecter les manchons aux

contacts négatifs (–).

NOTE: For returned audio, above, you must also do the following:

• Connect an audio input device to the Audio Return In 5-pole captive screw connector on the receiver.

• Install the optional Receiver-Tx-to-transmitter-Rx cable in step 3b.

e. If you want the FOX II units to pass serial or IR data or control signals, such as for serial Rx TxGnd

Tx RxGnd

IR Device

RS-232 Device

RS-232 IR

Tx Rx Tx RxG

OVER

FIBER

control of a projector, connect the master device to the transmitter and the slave device to the

receiver via the Over Fiber 5-pole captive screw connector.

NOTE: For returned RS-232 and IR responses (from the receiver to the transmitter, you must

install the Receiver-Tx-to-transmitter-Rx cable in step 3b.

Unbalanced Stereo Output Balanced Stereo Output

Unbalanced Stereo Input Balanced Stereo Input

Do not tin the wires!

Tip

No Ground Here

Tip

Sleeves

Tip

Ring

Tip

Ring

Sleeves

Tip

Ring

Tip

Ring

Sleeves

Tip

Sleeve

Tip

FOX II T HD 4K • Setup Guide (Continued)

f. For remote monitoring of the status of the Rx optical link, connect a locally constructed or obtained device to the two

RS-232 ALAR

Tx Rx G

REMOTE

rightmost Alarm poles of the Alarm and Remote RS-232 5-pole captive screw connector. The unit shorts both poles

together when no light is detected.

NOTE: The transmitter Alarm port reports the status of the link from the receiver.

g. For remote control of a unit and loading rmware, connect a host device, such as a computer or control system, to either of the

following ports:

Configuration port — The front panel mini USB connector.

CONFIG

NOTE: Extron recommends performing firmware updates via the Configuration port only.

Remote RS-232 port — The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector.

RS-232 ALAR

Tx Rx G

REMOTE

The protocol for the Remote port is as follows:

• 9600 baud •no parity •8 data bits

• 1 stop bit •no ow control

Step 3 — Throughput Connections

Receiver

ransmitter

OPTICAL

LINK

OPTICAL

LINK

NOTE: See the two fiber cable connection drawing at right. You can connect the transmitter to a compatible receiver

in one of two ways:

• One way (transmitter to receiver) only, perform step 3a.

• Two way (transmitter to receiver and return), perform steps 3a and 3b.

a. Connect the ber between the Tx port on the transmitter and the Rx port on the receiver (1, at right).

b. If you want the receiver to return serial data (such as responses from a controlled device) to the transmitter, connect

a cable between the Tx port on the receiver and Rx port on the transmitter (2).

Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]).

NOTE:The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.

Operation

After the receiver, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are

encountered, verify that the cables are routed and connected properly and that the display device has a compatible resolution and refresh

rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for

the Extron ofce nearest you.

Indications

CONFIG SIGNAL

VIDEO AUDIO

HDCP

INPUT

RETURN OUT

SELECT

EDID

Power LED — Indicates that power is applied to the unit.

Video LEDs —

Signal LED — Lights when the unit detects an input video signal.

HDCP LED — Lights when the input signal is HDCP encrypted.

Audio LEDs —

Input LED — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the audio signal

level drops below the threshold for 10 seconds or longer.

Return Out LED — Lights when analog audio is present on the transmitter Return Audio Output connector.

EDID

EDID Select rotary switch — Set this switch to one of the positions shown in the table below to select the source of the DDC or a specic

resolution.

Position 0 — An EDID that has previously been captured from a connected display or manually imported via an SIS command or the

Product Conguration Software.

Position 1 — The EDID is selected via the remote or USB port on the transmitter only, using an SIS command or the Extron Product

Conguration Software.

Position 2 — Use the EDID from the display connected to the receiver.

NOTE:EDID from the display connected to the receiver requires connection of both ber cables.

Position 3 — Use the EDID from the display

connected to the transmitter loop-through.

Positions 4 through E — Specify a resolution.

The table at right identies the resolutions

associated with the switch positions. All

resolutions are at 60 Hz with the exception of

4096x2160 (E), which is 30 Hz.

Position F — No EDID assigned.

Pos. Source or resolution Pos. Resolution Pos. Resolution

0 User recorded EDID 6 1366x768 C 2048x2160

1 Selected via RS-232 7 1440x900 D 2560x1600

2 Display on Rx output 8 1680x1050 E* 4096x2160

3 Display on Tx loop-through 9 1920x1080 F N/A

4 1280x720 A 1920x1200

5 1280x800 B 2048x1536

* 30 Hz

68-2300-50 Rev. Ax

04 15

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

FOX II T HD 4K • Setup Guide (Continued)

Application Diagram

STANDBY

CLASS2 WIRING

XPA1002

LEVEL

1212

LIMITER/

PROTECT

SIGNAL

INPUTS OUTPUT

REMOTE

VOL/MUTE

10V 50mA

100-240V 1.3A,50-60Hz

100-240V~ -.-AMAX

50-60 Hz

DISPLAYPORT

RS-232

OPTICAL

RESET

LINK

RS-232 IR

ALARM

Tx Rx G 1 2

L R

Tx Rx Tx RxG

AUDIO

OUTPUTS

AUDIO

RETURN IN

REMOTE

OVER

FIBER

FOX R DP 4K

POWER

12V

--AMAX

Tx Rx RTSCTS

COM1

TxRx

COM2

VC G

VOL RELAYS

1 2 C

12 3 4 G

DIGITALI/O

PWR OUT = 6W

eBUS

+V +S -S G

LAN

IPCP PRO 250

IR/S

100-240V~ 0.5AMAX

50-60 Hz

HDMI LOOP THRU

L R

RS-232

OPTICAL

RESET

LINK

RS-232 IR

ALARM

Tx Rx G 1 2

L R

Tx Rx Tx RxG

AUDIO

INPUTS

AUDIO

RETURN OUT

REMOTE

OVER

FIBER

FOX T HD 4K

POWER

SDCARD USB

PLAY STATUS

HDMI

Downscaled

to 1080p

4K HDMI

4K Media Player

MODEL80

Extron

Help System

Off

Display

Room

Control

Off

Mute

Screen

Lighting

December15, 2013 - 7:58 AM

Audio

Control

Volume

Mute

Tuner

123

VCR

LaptopPC DVD Doc

Cam

Tuner

Channel

Last

Presets

Enter

RS-232

Ethernet

Audio

4K DisplayPort

Extron

SI 28

Surface-mount

Speakers

Extron

XPA 1002

Power

Amplier

4K Display

Local

Monitor Up to 30 km (18.75 miles)

Singlemode Fiber

SM Model

Audio

RS-232

Extron

FOX T HD 4K

Fiber Optic Transmitter

Extron

FOX R DP 4K

Fiber Optic Receiver

Extron

TLP Pro 72

7" Table Top

TouchLink Pro

Touchpanel

TCP/IP

Network

Extron

IPCP Pro 250

IP Link Pro

Control Processor

Otros manuales para FOX II T HD 4K

Tabla de contenidos

Otros manuales de Transmisor de Extron electronics

Extron electronics

Extron electronics PowerCage MTP AV Series Manual de usuario

Extron electronics

Extron electronics UCS FT 901 Manual de usuario

Extron electronics

Extron electronics A/V Receiver MTP 4T 15HD RS Manual de usuario

Extron electronics

Extron electronics TP Series Manual de usuario

Extron electronics

Extron electronics DTP DVI 330 Manual de usuario

Extron electronics

Extron electronics PVT CV D Manual de usuario

Extron electronics

Extron electronics FOX3 T 301 Manual de usuario

Extron electronics

Extron electronics XTP T HDMI Manual de usuario

Extron electronics

Extron electronics DTP T FB 332 Manual de usuario

Extron electronics

Extron electronics ExSens Manual de usuario

Extron electronics

Extron electronics CAT 5 Manual de usuario

Extron electronics

Extron electronics DTP3 T 203 Manual de usuario

Extron electronics

Extron electronics XTP T VGA Manual de usuario

Extron electronics

Extron electronics MTP 15HD A Series Manual de usuario

Extron electronics

Extron electronics DTP2 T 201 D Series Manual de usuario

Extron electronics

Extron electronics XTP T HWP 101 Manual de usuario

Extron electronics

Extron electronics DTP T EU 4K 331 Manual de usuario

Extron electronics

Extron electronics FOX3 T 201 Manual de usuario

Extron electronics

Extron electronics TP T 15HD AV Manual de usuario

Extron electronics

Extron electronics MTP U T A D Manual de usuario

Extron electronics

Extron electronics MTP T 15HD A Manual de usuario

Extron electronics

Extron electronics XTP T HWP 101 Manual de usuario

Extron electronics

Extron electronics MTP T 15HD A D Manual de usuario

Extron electronics

Extron electronics DTP DVI 230 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario