Extron electronics System 8 Plus Manual de usuario

Extron • System 8/10 PLUS • User’s Manual • P/N 68-403-01 Rev. C

Eiki Installation Configuration and Connections

Page 1

SYSTEM 8/10 Plus

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: EIKI

Included Communications Adapter(s):

Quantity Part Number Description

1 26-467-01 ADP, UNV, “A”

1 26-474-01 ADP, UNV, “F”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S)AND CORRESPONDING

COMMUNICATIONSADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS

MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔”IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL

DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATIONAND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: EIKI LC-X1, LC-XGA 970

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 12345678910Adapter

✔Eiki LC-X1 0 0 F B J2 ¯¯¯¯¯ ¯¯26-467-01

✔Eiki XGA 970 0 0 F B J2 ¯¯¯¯¯ ¯¯26-474-01

Eiki Powerhouse Two 2 0 F B J2 ¯¯¯¯¯ ¯¯26-467-01

Extron • System 8/10 PLUS • User’s Manual • P/N 68-403-01 Rev. C

Eiki Installation Configuration and Connections

Page 2

Eiki LC-X1/XGA 970 Projector Configuration

Verify that the System 8/10 PLUS is already configured for the Eiki LC-X1/XGA

970 projector. The general setup is explained on page 3-4 and the switch

settings for the projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS

front panel. See bottom of page 3-3. The label on the back of the access cover

also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS

to verify that the main power is OFF; also turn the projector power OFF.

2. Set the switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

✔Eiki LC-X1/XGA970 0 0 F B J2 ¯¯¯¯ ¯¯¯ 26-467-01

or 26-474-01

_ RS5 is for RGB switching

delay. See page 3-4 for

more information on switch

functions.

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next

to “Eiki LC-X1/XGA970”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a host/peripheral system, set #3 and #5 to the up position

and the others down. See illustration to the left.

Use the illustration on the facing page to do the following steps.

5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female serial

port connector on the rear panel of the projector.

6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the

Comm Adapter to the 15-pin HD “Projector Control” port located on the rear

panel of the System 8/10 PLUS.

______ Secure the screws on all D connectors.

7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the Eiki

projector inputs according to the application requirements.

8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

9. Return System 8/10 PLUS and projector to normal operation.

Configured For:

RS-232

3456 7891012

SW15 DIP Switch

RS5 RS2

RS2

RS1

RS3

RS4

RS1

RS3 RS4

Extron • System 8/10 PLUS • User’s Manual • P/N 68-403-01 Rev. C

Eiki Installation Configuration and Connections

Page 3

Eiki LC-X1/XGA 970 Projector Connections

Use the illustration below when connecting the System 8/10 PLUS to an Eiki LC-

X1/XGA 970 projector. Refer to Eiki documentation to continue the installation.

_ If the installation includes looping (host/peripheral) switchers, see Chapter 5.

If Video Loop Back is part of the installation, see pages 2-10 and 2-11.

AUDIO 1

ANALOG RGB

CONTROL PORT 1USB 1

GBHV

AUDIO 1VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO

S-VIDEO

AUDIO 2

CONTROL PORT 2

SERIAL PORTAC JACK

USB 2

AUDIO OUT

AUDIO 1VIDEO/Y C/Cb(B-Y) Cr(R-Y)

RGBHV 5 BNC

15-Pin Male

S-Video

Composite

Video 9-Pin Female

9-Pin Male

ComAdapter

26-467-01 "A"

or 26-474-01 "F" A

Extron • System 8/10 PLUS • User’s Manual • P/N 68-403-01 Rev. C

Eiki Installation Configuration and Connections

Page 4

Eiki Powerhouse Two Projector Configuration

Verify that the System 8/10 PLUS is already configured for the Eiki Powerhouse

Two projector. The general setup is explained on page 3-4 and the switch

settings for the projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS

front panel. See bottom of page 3-3. The label on the back of the access cover

also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS

to verify that the main power is OFF; also turn the projector power OFF.

2. Set the switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

Eiki Powerhouse Two 2 0 F B J2 ¯¯¯¯ ¯¯¯ 26-467-01

_ RS5 is for RGB switching

delay. See page 3-4 for

more information on switch

functions.

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next

to “Eiki Powerhouse Two”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a host/peripheral system, set #3 and #5 to the up position

and the others down. See illustration to the left.

Use the illustration on the facing page to do the following steps.

5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female serial

port connector on the rear panel of the projector.

6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the

Comm Adapter to the 15-pin HD “Projector Control”port located on the rear

panel of the System 8/10 PLUS.

______ Secure the screws on all D connectors.

7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the Eiki

projector inputs according to the application requirements.

8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

9. Return System 8/10 PLUS and projector to normal operation.

Configured For:

RS-232

3456 7891012

SW15 DIP Switch

RS5 RS2

RS2

RS1

RS3

RS4

RS1

RS3 RS4

Extron • System 8/10 PLUS • User’s Manual • P/N 68-403-01 Rev. C

Eiki Installation Configuration and Connections

Page 5

Eiki Powerhouse Two Projector Connections

Use the illustration below when connecting the System 8/10 PLUS to an Eiki

Powerhouse Two projector. Refer to Eiki documentation to continue the

installation.

_ If the installation includes looping (host/peripheral) switchers, see Chapter 5.

If Video Loop Back is part of the installation, see pages 2-10 and 2-11.

AUDIO 1 ANALOG RGB

ANALOG RGB

CONTROL PORT 1USB 1

GBHV

AUDIO 1VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO

S-VIDEO

AUDIO 2

CONTROL PORT 2

SERIAL PORTAC JACK

USB 2

AUDIO OUT

AUDIO 1VIDEO/Y C/Cb(B-Y) Cr(R-Y)

DIGITAL

RGBHV 5 BNC

15-Pin Male

S-Video

Composite

Video 9-Pin Female

9-Pin Male

Comm Adapter

26-467-01 "A" A

Otros manuales para System 8 Plus

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Extron electronics

Extron electronics

Extron electronics SW8/12 Manual de usuario

Extron electronics

Extron electronics System 7SC Manual de usuario

Extron electronics

Extron electronics SW2 RGBHV Manual de usuario

Extron electronics

Extron electronics DTP T USW 233 Manual de usuario

Extron electronics

Extron electronics IN1804 Series Manual de usuario

Extron electronics

Extron electronics MPS 601 Manual de usuario

Extron electronics

Extron electronics MGP 641 xi Series Manual de usuario

Extron electronics

Extron electronics ISS 612 Manual de usuario

Extron electronics

Extron electronics SW HDMI LC Manual de usuario

Extron electronics

Extron electronics MSW 4SV rs Series Manual de usuario

Extron electronics

Extron electronics RGB 320 Manual de usuario

Extron electronics

Extron electronics MPS 601 Manual de usuario

Extron electronics

Extron electronics MTPX Plus Series Manual de usuario

Extron electronics

Extron electronics Matrix 12800 Series Manual de usuario

Extron electronics

Extron electronics YCS SW2 A Manual de usuario

Extron electronics

Extron electronics 650 UT Manual de usuario

Extron electronics

Extron electronics VSW 2VGA A Manual de usuario

Extron electronics

Extron electronics VEGA AUDIO SW6 Manual de usuario

Extron electronics

Extron electronics IN1604 DTP Manual de usuario

Extron electronics

Extron electronics PVS 305SA Manual de usuario

Extron electronics

Extron electronics SW HD 4K PLUS Series Manual de usuario

Extron electronics

Extron electronics IN1508 Manual de usuario

Extron electronics

Extron electronics SW2 VGA DA2 A Manual de usuario

Extron electronics

Extron electronics MSW 4V rs Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario