Extreme Networks AP510C Manual de instalación

AP510C and AP510CX Hardware User Guide

Read about and view specifications and compliance information for the AP510C and AP510CX in this topic. Install the AP510C and AP510CX using

this topic.

The AP510C and AP510CX are high-performance dual-5G and dual band access points.

Both are designed for indoor high-density environments that require HD video streaming and large file transfers. The AP510CX has external anten-

nas (sold separately), and an extended temperature range for industrial environments. These devices support IEEE 802.11ax Orthogonal Frequency-

Division Multiple Access (OFDMA) multi-user access.

Both access point have a Bluetooth BLE i-beacon for location based services.

For regulatory and compliance information, see "Regulatory Compliance Statements".

Important! Change the Country Code

If your access point is configured for the WorldRegulatory Domain, it is important to set the country code to the country in which the APwill be

deployed to meet regulatory requirements and for optimal wireless operation. To do this, follow these steps:

The country code selection is for World models only and is not available to FCC, CAN, and other country-specific models. Per FCC reg-

ulations, all Wi-Fi products marketed in the United States must be set to U.S. channels only.

1. Power on the AP and allow it to find and connect to ExtremeCloudIQ. Once the APis connected it appears in the table of devices on the

Manage > Devices page.

2. Select the check box next to the AP, and then choose Assign Country Code from the Actions drop-down list. In the dialog box, select the

appropriate country from the drop-down list, and then click Save.

3. Upload your changes to the device.

Safety Guidelines

The safety information in this section applies to AP510C and AP510CX devices.

The following safety icons are used in these guidelines to identify the type of precaution:

AP510C and AP510CX Hardware Guide

This icon indicates a general caution. Failure to comply with a caution notification can result in damage to equipment.

This icon indicates an electrical caution. Failure to comply with an electrical notification can result in serious injury or

death, and extensive damage to equipment.

The following table lists the safety precautions you should follow when installing your AP510C and AP510CX devices.

Extreme Networks devices must be installed by a professional installer who is certified to install these types of devices

and to ensure that they are properly grounded and meet applicable local and national electrical codes.

These devices are intendedfor indoor use only.

Do not install the device in an environment where the operating ambient temperature might exceed the recom-

mended ranges.

For products available in the USA/Canada market, for the 2.4 GHz band, only channels 1-11 can be operated. Selec-

tion of other channels is not possible.

Changes or modifications made to this device that are not expressly approved by the party responsible for com-

pliance could void the user's authority to operate the equipment.

Use only attachments and accessories specified by Extreme Networks.

These devices are not intended for use by persons (including children) with reduced physical, sensory, or mental cap-

abilities, or with lack of experience of knowledge unless they are given supervision or instruction concerning use of the

devices by a person who is responsible for their safety. Children should be supervised to ensure that they do not play

with the devices.

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when elec-

tronic components are improperly handled and can result in complete or intermittent failures. Be sure to follow ESD-pre-

vention procedures when handling electronic components and equipment.

During operation, the surfaces of the AP510C and AP510CX can become hot. Use caution when handling.

To meet US federal radiation exposure requirements, these devices should be installed at a minimum distance of 10"

(25.5 cm) from people or animals.

To meet EUradiation exposure requirements, these devices should be installed at a minimum distance of 8" (20 cm)

from people or animals.

To meet Canadian radiation exposure requirements, these devices should be installed at a minimum of 30 cm from

people or animals.

Install the AP

Youcan mount the AP510C and AP510CXon a flat surface or wall, or on the rails of a standarddropped ceiling grid. There is also an accessory

mounting bracket that allows you to install the device in Armstrong-style dropped ceilings (ordered separately).

The following sections describe how to install your AP510C and AP510CX devices and connect them to the network.

Shipping Carton Contents

The AP510C and AP510CX shipping carton contains the following items:

lAP510C or AP510CX chassis

lMounting bracket

lRead Me card

AP510C and AP510CX Hardware Guide

The AP510C and AP510CX ship with a mounting bracket that lets you easily install them on the T-rail of a standard dropped ceiling grid. The

fol-lowing illustrations show how to install the bracket to the ceiling rail, and then install the APon the bracket.

Install the APon a Ceiling Track

AP510C and AP510CX Hardware Guide

Once the bracket is secure, youcan install the AP by aligning the red dot on the bracket with the red dot on the bottom ofthe AP. Keeping the

dots aligned, raise the APup until the bracket fits into the circular depression in the bottom of the AP. When the APis firmly seated, rotate it clock-

wise until it clicks in to place. The process is identical for both models.

Mount the APon a Wall

Use the holes in the accessory wall-mount bracket as a template to markthe wall. Drill holes in the wall and attach the bracket to the wall using

wall screws and wall anchors if necessary. Attach the APto the bracket in the same manner as shown in the previous section. Install external

antennas on AP510CX devices. Order antennas from Extreme Networks (AH-ACC-ANT-AX-KT).

Lock the AP

You can secure the AP using a Kensington®lock in the lock slot on the side of the device, or you can use a security bracket and a crosshead

AP510C and AP510CX Hardware Guide

screw or a security screw. Security brackets and screws can be ordered separately from Extreme Networks (not available in Brazil).

Extreme Networks recommends a variety of Kensington locks. For more information, contact your sales representative.

Hardware Components

Youcan see the hardware components of the AP510C and AP510CX in the illustration below and read about them in the sections that follow. The

illustration shows an AP510C model. The components are the same for both models, except the AP510CXhas eight external antenna connectors.

Component Descriptions

Status Light

The status light conveys operational states for system power, firmware updates, Ethernet and wireless interface activity, and major alarms. The

AP510C and AP510CXhave a rectangularstatus light on the top right corner ofthe chassis. At setup, this light cycles through the following

sequence:

lSteady Amber: The device is initializing.

lSlow-blinking White:The device is receiving 802.3af power, instead of 802.3at power.

lFast-blinking White: The device is looking for a mesh neighbor from which to obtain a password.

lSlow-blinking Amber (AFpower mode only): The device is attempting to establish a connection or has established a CAPWAPconnection

with ExtremeCloudIQ.

lFast-blinking Amber: The device is performing a IQEngine or ExtremeCloudIQ upgrade.

lSteady White: The device has successfully established a CAPWAP connection and is operating normally.

Ethernet Ports

The ETH0 port is autosensing 100/1000/2500G BASE-T/TX Mbps, with IEEE 802.3af- or 802.3at-compliant PoE, and requires Cat6 cable.

The Eth 1 port is autosensing 10/100/1000 BASE-T/TX Mbps, wth IEEE 802.3af- or 802.3at-compliant PoE.

There are three power options. In the event of a failure, the device will automatically reboot using the next priority power source. When the failed

power source is replaces, you must manually reboot the device again to use the repaired power source. For example, if Eth0 and Eth1 are in use,

and Eth0 fails, the device will automatically reboot using Eth1. When Eth0 is restored, you will need to manually reboot the device to again use

Eth0.

AP510C and AP510CX Hardware Guide

The priorities are:

lFirst priority: 12VDC

lSecond priority: PoE - Eth0

lThird priority: PoE - Eth1

Hardware Specifications

The following sections list radio, device, power, and environmental specifications for the AP510C and AP510CX.

Radio Specifications

Bluetooth BLE Beacon

l2402 - 2480 MHz

lFrequency Hopping Spread-spectrum (FHSS)

802.11a

l5.150-5.350, 5.470 - 5.850 GHz operating frequency

lOrthogonal Frequency Division Multiplexing (OFDM) modulation

lRates (Mbps): 54, 48, 36, 24, 12, 9, 6 with auto fallback

802.11b

l2.4-2.48 GHz operating frequency

lDirect-Sequence Spread-Spectrum (DSSS) modulation

lRates (Mbps): 11, 5.5, 2.1 with auto fallback

802.11g

l2.4-2.48 GHz operating frequency

lOrthogonal Frequency Division Multiplexing (OFDM) modulation

lRates (Mbps): 54, 48, 36, 24, 12, 9, 6 with auto fallback

802.11n

l2.4-2.48 and 5.150-5.350, 5.470 - 5.850 GHz operating frequency

l802.11n modulation

lRates: MCS0 - MCS7

l4x4 MIMO radio

lHT20 support

lHT40 support (5 GHz only)

lA-MPDU and A-MSDU frame aggregation

802.11ac

l802.11ac modulation (256-QAM)

l2.4 - 2.48 GHz MCS0-9, NSS=1-4

l5.150-5.350, 5.470 - 5.850 GHz operating frequency

lRates: MCS0 - MCS9, NSS = 1-4

l4x4 MIMO radio

lVHT20/VHT40/VHT80/VHT160 support

802.11ax

l5.150-5.350, 5.470 - 5.850 GHz operating frequency

l2.4 - 2.48 GHz operation frequency

l802.11ax modulation (1024-QAM)

lRates: MCS0 - MCS11, NSS = 1-4

lOFDMA support

AP510C and AP510CX Hardware Guide

l4x4 MU-MIMO

lHE20/HE40/HE80/HE160 support

Transmit Power and Sensitivity Specifications

Output power may be limited by regulatory requirements.

2.4 H Tolerance +2/-2 dB @25°C

Mode Data Rate Power Unit

11b 1,2,5.5,11 18 dBm

11g 54 Mbps 15 dBm

48 Mbps 16 dBm

36 Mbps 17 dBm

6 Mbps 18 dBm

HE20 MCS 0,1,2 18 dBm

MCS 3 17 dBm

MCS 4, 5 16 dBm

MCS 6,7 15 dBm

MCS 8,9 14 dBm

MCS 10,11 12 dBm

2.4 G Sensitivity

11b 1 Mbps -99 dB

11 Mbps -90 dB

11g 6 Mpbs -96 dB

36 Mpbs -84 dB

48 Mbps -80 dB

54 Mbps -78 dB

HE20 MCS 0 -95 dB

MCS 1 -91 dB

MCS 2 -89 dB

MCS 3 -86 dB

MCS 4 -83 dB

MCS 5 -79 dB

MCS 6 -77 dB

MCS 7 -76 dB

MCS 8 -72 dB

MCS 9 -70 dB

MCS 10 -67 dB

MCS 11 -64 dB

AP510C and AP510CX Hardware Guide

Mode Data Rate Power Unit

11a 54 Mbps 18 dBm

48 Mbps 18 dBm

36 Mbps 19 dBm

6 Mbps 20 dBm

HE20 MCS 0, 1, 2 20 dBm

MCS 3, 4 19 dBm

MCS 5, 6 18 dBm

MCS 7, 8 17 dBm

MCS 9 16 dBm

MCS 10 15 dBm

MCS 11 14 dBm

HE40 MCS 0, 1, 2 19 dBm

MCS 3, 4, 5 18 dBm

MCS 6,7,8 17 dBm

MCS 9 16 dBm

MCS 10 15 dBm

MCS 11 14 dBm

HE80 MCS 0,1,2 19 dBm

MCS 3,4,5 18 dBm

MCS 6,7,8 17 dBm

MCS 9 16 dBm

MCS 10 15 dBm

MCS 11 14 dBm

HE160 MCS 0,1,2 19 dBm

MCS 3,4,5 18 dBm

MCS 6,7,8 17 dBm

MCS 9 16 dBm

MCS 10 15 dBm

MCS 11 14 dBm

5 G Sensitivity

11a 6 Mbps -94 db

36 Mbps -83 db

48 Mbps -79 db

54 Mbps -77 db

HE20 MCS 0 -94 db

MCS 1 -91 db

MCS 2 -88 db

MCS 3 -86 db

AP510C and AP510CX Hardware Guide

5 G Tolerance +2/-2 dB @25°C

Mode Data Rate Power Unit

MCS 4 -82 db

MCS 5 -78 db

MCS 6 -77 db

MCS 7 -75 db

MCS 8 -71 db

MCS 9 -69 db

MCS 10 -66 db

MCS 11 -63 db

HE40 MCS 0 -92 db

MCS 1 -88 db

MCS 2 -86 db

MCS 3 -83 db

MCS 4 -80 db

MCS 5 -76 db

MCS 6 -74 db

MCS 7 -73 db

MCS 8 -69 db

MCS 9 -67 db

MCS 10 -63 db

MCS 11 -60 db

HE80 MCS 0 -88 db

MCS 1 -85 db

MCS 2 -83 db

MCS 3 -80 db

MCS 4 -77 db

MCS 5 -73 db

MCS 6 -71 db

MCS 7 -69 db

MCS 8 -66 db

MCS 9 -64 db

MCS 10 -60 db

MCS 11 -57 db

HE160 MCS 0 -85 db

MCS 1 -82 db

MCS 2 -80 db

MCS 3 -77 db

MCS 4 -74 db

MCS 5 -70 db

AP510C and AP510CX Hardware Guide

Mode Data Rate Power Unit

MCS 6 -68 db

MCS 7 -66 db

MCS 8 -63 db

MCS 9 -61 db

MCS 10 -57 db

MCS 11 -54 db

Device Specifications

lChassis dimensions:

AP510C: 8.1” W 8.1” H 1.46” D (205 mm x 205 mm x 37 mm)

AP510CX: 8.9” W 8.9” H 1.48” D (225 mm x 225 mm x 37.5 mm)

lWeight:

AP510C: 2.61 lbs (1.18 kilograms)

AP510CX (without antennas): 2.82 lbs (1.28 kilograms)

lAntennas

AP510CX option 1: 4 external omnidirectional 2.4/5 GHz dual band antennas and 4 external omnidirectional 5 GHz antennas

AP510CX option 2: 8 internal omnidirectional 5 GHz antennas

AP510C: 4 internal omni directional 2.4/5 GHz dual bandantennas, and4 internal omnidirectional 5 GHz antennas

AP510C/AP510CX: 1 internal BLE antenna

lETH0 Ethernet port: autosensing 100/1000/2500G BASE-T/TX Mbps, with IEEE 802.3af- or 802.3at-compliant PoE, and requires Cat6 cable.

lETH1 Ethernet port: autosensing 10/100/1000 BASE-T/TX Mbps, with IEEE 802.3af- or 802.3at-compliant PoE

Antenna Gain

lBLE 2.4 GHz: 4.2 dBi gain

lWiFi02.4 GHz: 5 dBi gain

lWiFi1 5 GHz:5.5 dBi gain

Power Specifications

lPoE input voltage range: 37-57 V

lRJ45 power input pins: Wires 4, 5, 7, 8 or 1, 2, 3, and 6

Power Consumption

AP510C:

lDC power: 18.72 W with USB, 15.72 W without USB

lPoE: 21.78 W with USB, 18.78 W without USB

AP510CX:

lDC power: 18.72 W with USB, 15.72 W without USB

lPoE: 20.79 W with USB, 17.79 W without USB

Environmental Specifications

lAP510C: Operating temperature: 32° to 104° F (0° to 40° C)

lAP510CX: Operating temperature: -4° to 131° F (-20° to 55° C)

lStorage temperature: -40° to 185° F (-40° to 85° C)

lRelative Humidity: 5 to 95% RH (noncondensing)

AP510C and AP510CX Hardware Guide

lWiFi2 2.4 GHz:5.5 dBi gain

WiFi2 5 GHz:6 dBi gain

WiFi3 2.4 GHz:6.9 dBi gain

WiFi3 5 GHz:7.2 dBi gain

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Extreme Networks

Extreme Networks

Extreme Networks ExtremeWireless AP460i Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP4000 Manual de usuario

Extreme Networks

Extreme Networks AP60C Manual de instalación

Extreme Networks

Extreme Networks ExtremeMobility AP410i/e Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP410C-1-WR Manual de usuario

Extreme Networks

Extreme Networks Altitude 4511 Manual de usuario

Extreme Networks

Extreme Networks WS-AP3805i Manual de usuario

Extreme Networks

Extreme Networks Altitude 4700 Series Manual de usuario

Extreme Networks

Extreme Networks AP460C Manual de usuario

Extreme Networks

Extreme Networks Extreme Wireless WSAP3825i Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless WS-AP3965i-FCC Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless WS-AP3915i-FCC Manual de usuario

Extreme Networks

Extreme Networks Altitude 450 Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP310i Manual de usuario

Extreme Networks

Extreme Networks Altitude 3500 Series Manual de instalación y operación

Extreme Networks

Extreme Networks AP410C Manual de usuario

Extreme Networks

Extreme Networks Altitude 4522 Series Manual de usuario

Extreme Networks

Extreme Networks AP-7522 Manual de usuario

Extreme Networks

Extreme Networks AP-8533 Manual del propietario

Extreme Networks

Extreme Networks ExtremeMobility AP460i Manual de usuario

Extreme Networks

Extreme Networks Altitude 350-2 Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless WS-AP3805i-FCC Manual de usuario

Extreme Networks

Extreme Networks ExtremeMobility AP560i-FCC Manual de usuario

Extreme Networks

Extreme Networks Altitude 3550 Guía de referencia rápida

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario