Extreme Networks AP-7522 Manual de usuario

Updated March 2017

9035076 Rev00

AP-7522 Access Point

Installation Guide

2AP-7522 Access Point

Legal Notice

Extreme Networks, Inc. reserves the right to make changes in specifications and other

information contained in this document and its website without prior notice. The reader

should in all cases consult representatives of Extreme Networks to determine whether

any such changes have been made.

The hardware, firmware, software or any specifications described or referred to in this

document are subject to change without notice.

Trademarks

Extreme Networks and the Extreme Networks logo are trademarks or registered

trademarks of Extreme Networks, Inc. in the United States and/or other countries.

All other names (including any product names) mentioned in this document are the

property of their respective owners and may be trademarks or registered trademarks of

their respective companies/owners.

For additional information on Extreme Networks trademarks, please see:

www.extremenetworks.com/company/legal/trademarks/

Support

For product support, including documentation, visit:

www.extremenetworks.com/documentation/

Installation Guide 3

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4 AP-7522 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.5 AP-7522 Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.0 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.1 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3 Access Point Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4 Power Injector System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.5 Wall Mount Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.5.1 Wall Mount Procedure - New Installation . . . . . . . . . . . . . . 13

2.5.2 Wall Mount Procedure - Existing AP Replacement . . . . . . . 14

2.6 Suspended Ceiling T-Bar Mount Installation . . . . . . . . . . . . . . . 15

2.7 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.0 Basic Access Point Configuration . . . . . . . . . . . . . . . . . . . . . . . 20

4.0 AP-7522 Access Point Specifications . . . . . . . . . . . . . . . . . . . . . 29

4.1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4.2 Physical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4.3 Radio Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.1 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.2 Wireless Device Country Approvals . . . . . . . . . . . . . . . . . . . . . . 31

5.2.1 Country Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.2.2 Frequency of Operation - FCC and IC . . . . . . . . . . . . . . . . 32

5.3 Health and Safety Recommendations . . . . . . . . . . . . . . . . . . . . . 33

5.3.1 Warnings for the use of Wireless Devices . . . . . . . . . . . . . . 34

4AP-7522 Access Point

5.3.2 Potentially Hazardous Atmospheres - Fixed Installations . . 34

5.3.3 Safety in Hospitals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.4 RF Exposure Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.4.1 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.4.2 International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.4.3 EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.4.4 US and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.5 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.6 Radio Frequency Interference Requirements - FCC . . . . . . . . . . 36

5.6.1 Radio Transmitters - Part 15 . . . . . . . . . . . . . . . . . . . . . . . . 36

5.6.2 Radio Frequency Interference Requirements - Canada. . . . 36

5.7 CE Marking and European Economic Area (EEA) . . . . . . . . . . . 37

5.8 Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

5.9 Japan (VCCI) - Voluntary Control Council for Interference . . . . . 38

5.10 Korea Warning Statement for Class B ITE . . . . . . . . . . . . . . . . 38

5.11 Other Countries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

5.12 Waste Electrical and Electronic Equipment (WEEE) . . . . . . . . 40

5.13 Turkish WEEE Statement of Compliance . . . . . . . . . . . . . . . . . 41

6.0 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

7.0 End-User Software License Agreement . . . . . . . . . . . . . . . . . . . 43

8.0 AP-7522 Access Point China ROHS Compliance . . . . . . . . . . . . 50

Installation Guide 5

1 Introduction

The AP-7522 external antenna and internal antenna Access Point’s are mid-tier Access

Point’s with a relatively small footprint which supports functionality for dependable and

efficient network performance.The AP-7522 is a 2x2:2 802.11ac Access Point utilizing one

2.4 GHz 802.11n radio and one 5 GHz 802.11ac radio. The Access Point housing is

Plenum-rated (UL2043).

The Access Point’s unique WiNG 5 software enables the Access Point to function as either a

Standalone Access Point, an Adaptive Access Point, or a Virtual Controller.

If new to Access Point technology, refer to the WiNG Access Point System Reference Guide

to familiarize yourself with Access Point technology and the feature set supported by the

WiNG operating system. The guide is available at www.zebra.com/support.

This document is written for the qualified network device installer.

1.1 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

1.2 Warnings

• Read all installation instructions and site survey reports, and verify correct equipment

installation before connecting the AP-7522 Access Point.

• Remove jewelry and watches before installing this equipment.

• Verify any device connected to this unit is properly wired and grounded.

• Verify there is adequate ventilation around the device, and that ambient temperatures

meet equipment operation specifications.

NOTE Tips, hints, or special requirements that you should take

note of.

CAUTION Care is required. Disregarding a caution can result in

data loss or equipment malfunction.

WARNING! Indicates a condition or procedure that could result in

personal injury or equipment damage.

6AP-7522 Access Point

1.3 Site Preparation

• Consult your site survey and network analysis reports to determine specific

equipment placement, power drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify and document where all installed components are located.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Identify and prepare Ethernet and console port connections.

• Verify cable lengths are within the maximum allowable distances for optimal signal

transmission.

1.4 AP-7522 Package Contents

An AP-7522 Access Point is available in external antenna (AP-7522) and internal antenna

(AP-7522I) configurations. An AP-7522 ships with the following:

• AP-7522 Access Point

• AP-7522 Installation Guide (This Guide)

• Wall mount screws and mounting bracket

1.4.1 Features

An AP-7522 Access Point supports the following feature set:

• Two RJ-45 connectors (GE1/POE and Console)

• Two LED indicators

• One 2.4 GHz 802.11n radio and one 5 GHz 802.11ac radio

• 2x2 MIMO, 2 spatial streams

The GE1/POE accepts 802.3at or 802.3af compliant power from an external source.

NOTE When operating in a Gigabit Ethernet environment, CAT-5e

or CAT-6 cable is recommended for Gigabit operation.

Installation Guide 7

1.5 AP-7522 Antennas

1.5.1 AP-7522 Dual Band 2.4 GHz / 5 GHz Antennas - US

An AP-7522 external antenna Access Point supports the following dual band antenna options

for the US:

* This antenna is for indoor placement only.

1.5.2 AP-7522 Dual Band 2.4 GHz / 5 GHz Antennas - EU

*An external antenna AP-7522 supports the following dual band antenna options for the EU:

NOTE Per FCC requirement, the use of the Access Point on

UNII-1 of 5GHz band requires installers to input antenna

elevation gain during configuration if the AP placement is for

outdoor coverage. This information can be found in Zebra

antenna guide located at www.zebra.com/support.

Part Number Antenna Type 2.4 GHZ Gain

(dBi) 5 GHZ Gain

(dBi)

Elevation Gain

for outdoor

placement (dBi)

ML-2452-APA2-01 Dipole 3.17 4.85 na*

ML-2452-HPA5-036 Dipole 3 5 -2.56

ML-2452-APAG2A1-01 Dipole 2.7 1.7 na*

ML-2452-HPAG4A6-01 Dipole 4 7.3 5.7

ML-2452-HPA6-01 Dipole 5.3 6.1 4.09

ML-2452-PNL9M3-N36 Polarized-Panel 11 10.7 7.3

ML-2452-PNA5-01R Panel 5.5 6 5.2

ML-2452-PTA3M3-036 Patch 5 4 na*

ML-2452-VMM5M3-N72 Patch 4.5 5.4 2.9

Part Number Antenna Type 2.4 GHZ Gain (dBi) 5 GHZ Gain (dBi)

ML-2452-APA2-01 Dipole 3.17 4.85

ML-2452-HPA5-036 Dipole 3 5

ML-2452-APAG2A1-01 Dipole 2.7 1.7

ML-2452-HPAG4A6-01 Dipole 4 7.3

ML-2452-HPA6-01 Dipole 5.3 6.1

8AP-7522 Access Point

1.5.3 AP-7522 Internal Antenna Model

An AP-7522 internal antenna Access Point supports the following dual band antenna:

1.5.4 AP-7522 Dual Band 2.4 GHz / 5 GHz Antennas - Canada

*An external antenna AP-7522 supports the following dual band antenna options for Canada: :

ML-2452-PNL6M3-N36 Polarized-Panel 6 6

ML-2452-PNA5-01R Panel 5.5 6

ML-2452-PTA3M3-036 Patch 5 4

ML-2452-VMM5M3-N72 Patch 4.5 5.4

Antenna Type 2.4 GHZ Gain (dBi) 5 GHZ Gain (dBi)

PIFA 4.13 5.92

Part Number Antenna Type 2.4 GHZ Gain (dBi) 5 GHZ Gain (dBi)

ML-2452-APA2-01 Dipole 3.17 4.85

ML-2452-HPA5-036 Dipole 3 5

ML-2452-APAG2A1-01 Dipole 2.7 1.7

ML-2452-HPAG4A6-01 Dipole 4 7.3

ML-2452-HPA6-01 Dipole 5.3 6.1

ML-2452-PNL9M3-N36 Polarized-Panel 11 10.7

ML-2452-PNA5-01R Panel 5.5 6

ML-2452-PTA3M3-036 Patch 5 4

ML-2452-VMM5M3 -N72 Patch 4.5 5.4

NOTE A professional installer must enter the antenna type, gain,

and indoor/outdoor placement using the CLI. The AP

software uses this information and hardcode maximum

limits determined during testing to limit the EIRP. Please

note, the maximum EIRP in band 5.25-5.35GHz is limited to

23dBm. This limit is hardcoded in the software for this band.

Part Number Antenna Type 2.4 GHZ Gain (dBi) 5 GHZ Gain (dBi)

Installation Guide 9

2 Hardware Installation

2.1 Installation Instructions

An AP-7522 Access Point mounts either on a wall (with M 3.5 x 0.6 x 23 MM pan head screws

and mounting bracket- or equivalent) or on a suspended ceiling T-bar.

To prepare for the installation:

1. Match the part number on the purchase order with the part numbers in the packing list

and on the case of the Access Point.

2. Verify the contents of the box include the intended AP-7522 Access Point, and the

included hardware matches the package contents

(see AP-7522 Package Contents on page 6).

3. Review site survey and network analysis reports to determine the location and

mounting position for the AP-7522 Access Point.

4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3at or 802.3af power

source and run the cable to the installation site. Ensure there is sufficient slack on the

cable to perform the installation steps.

Part Number Description

AP-7522-67040-US AP-7522 dual radio 802.11ac 2x2:2 MIMO Access Point external antenna

US version

AP-7522-67040-WR AP-7522 dual radio 802.11ac 2x2:2 MIMO Access Point external antenna

International version

AP-7522-67040-EU AP-7522 dual radio 802.11ac 2x2:2 MIMO Access Point external antenna

EU version

AP-7522-67030-US AP-7522 dual radio 802.11ac 2x2:2 MIMO Access Point internal antenna

US version

AP-7522-67030-WR AP-7522 dual radio 802.11ac 2x2:2 MIMO Access Point internal antenna

International version

AP-7522-67030-EU AP-7522 dual radio 802.11ac 2x2:2 MIMO Access Point internal antenna

EU version

NOTE When operating in a Gigabit Ethernet environment, CAT-5e

or CAT-6 cable is recommended for Gigabit operation.

10 AP-7522 Access Point

2.2 Precautions

Before installing an AP-7522 Access Point, verify the following:

• Your are using the correctly rated power solution for the AP-7522 (either the

AP-PSBIAS-2P3-ATR power injector or the PWRS-14000-54R external power supply)

• Do not install the AP-7522 in wet or dusty areas.

• Verify the environment has a continuous temperature range between -4° F to 104°

F/-20° C to 40° C for external antenna Access Points and 32° F to 104° F/0° C to 40°

C for internal antenna Access Points.

2.3 Access Point Placement

For optimal performance, install the Access Point away from transformers, heavy-duty motors,

fluorescent lights, microwave ovens, refrigerators and other industrial equipment. Signal loss

can occur when metal, concrete, walls or floors block transmission. Install the Access Point in

an open area or add Access Points as needed to improve coverage.

Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not

bright enough. An area lit sharply might minimize coverage and create dark areas. Uniform

antenna placement in an area (like even placement of a light bulb) provides even, efficient

coverage.

Install the Access Point at an ideal height of 10 feet from the ground.

To maximize the Access Point’s radio coverage area, conduct a site survey to define and

document radio interference obstacles before installing the Access Point.

2.4 Power Injector System

An AP-7522 Access Point can receive power via an Ethernet cable connected to the GE1/POE

(LAN) port.

When users purchase a WLAN solution, they often need to place Access Points in obscure

locations. In the past, a dedicated power source was required for each Access Point in addition

to the Ethernet infrastructure. This often required an electrical contractor to install power drops

at each Access Point location. The Power Injector merges power and Ethernet into one cable,

reducing the burden of installation and allowing optimal Access Point placement in respect to

the intended coverage area.

CAUTION Using a non-compliant injector, or an injector supporting

legacy modes will not allow the AP-7522 to function at

optimum performance levels.

Otros manuales para AP-7522

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Extreme Networks

Extreme Networks

Extreme Networks ExtremeWireless WS-AP3915i-FCC Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP460i Manual de usuario

Extreme Networks

Extreme Networks AP3000 Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP5010 Manual de usuario

Extreme Networks

Extreme Networks AP-8432 Manual de usuario

Extreme Networks

Extreme Networks IdentiFi 3600 Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP560i Manual de usuario

Extreme Networks

Extreme Networks Altitude 350-2 Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP560i Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP560h Manual de usuario

Extreme Networks

Extreme Networks Extreme Wireless WSAP3825i Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP3917i Manual de usuario

Extreme Networks

Extreme Networks Altitude 4000 Series Manual de usuario

Extreme Networks

Extreme Networks ExtremeRouting SLX 9640 Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless WS-AP3805i-FCC Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP3935e Manual de usuario

Extreme Networks

Extreme Networks Altitude 3510 Manual de usuario

Extreme Networks

Extreme Networks AP460C Manual de usuario

Extreme Networks

Extreme Networks Altitude 4700 Series Manual de usuario

Extreme Networks

Extreme Networks Extreme Wireless WSAP3825i Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP3000X Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless 31012 Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless WS-AP3965i-FCC Manual de usuario

Extreme Networks

Extreme Networks ExtremeWireless AP310i Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario