Extreme Networks ReachNXT 100-8t Manual de usuario

ReachNXT™100-8t Quick Start Guide

This guide describes how to install the ReachNXT™100-8t port extender and configure the uplinked

ExtremeXOS switch to detect and initialize the port extender.

Safety Information

Only trained service personnel should perform service to Extreme Networks switches and their

components. Trained service personnel have read all related installation manuals, have the technical

training and experience necessary to be aware of the hazards to which they are exposed in performing a

task, and are aware of measures to minimize the danger to themselves or other persons.

Before installing a ReachNXT 100-8t port extender into your network:

●Read the latest installation and safety information provided in the ReachNXT 100-8t User Guide.

●See Appendix A of the ReachNXT 100-8t User Guide for additional information regarding regulatory

compliance certifications.

NOTE

Die deutsche Version der für dieses Produkt von Extreme Networks relevanten Sicherheitshinweise finden sich im

Abschnitt “Sicherheitshinweise” im ReachNXT 100-8t User Guide. Dieses Installationshandbuch steht auf der

folgenden Webseite zum Download zur Verfügung: http://www.extremenetworks.com/services/hardware-userguide.aspx.

Getting Documentation

You can download the ReachNXT 100-8t User Guide and other Extreme Networks product

documentation from:

http://www.extremenetworks.com/services/documentation.aspx

Requirements

Before you begin, make sure you have the following:

●ReachNXT 100-8t ExtremeXOS port extender

●ExtremeXOS switch to serve as the uplinked switch. The uplinked ExtremeXOS switch must be

running ExtremeXOS version 11.2 or higher.

●Cable to connect the ReachNXT 100-8t to the uplinked ExtremeXOS switch

Depending on your installation, you may also have the following:

●Optional SFP module, if one will be used as the connector to the uplinked ExtremeXOS switch

●Optional magnet mounting kit, if you will mount the ReachNXT 100-8t in a fixed location

ReachNXT™100-8t Quick Start Guide

●Optional AC adapter, if the ReachNXT 100-8t will be powered using AC power

If an SFP module will be used for the uplink connection to the ExtremeXOS switch, you must power

the ReachNXT 100-8t using AC power.

●Kensington lock (not supplied) to secure the ReachNXT 100-8t to its location using its Kensington

lock slot

Installing the ReachNXT 100-8t Hardware

To install the ReachNXT 100-8t port extender:

1If an SFP module will be used for the connector to the uplinked ExtremeXOS switch, install the SFP

module in the ReachNXT 100-8t (port 9x) according to the instructions supplied with the module.

You must use the AC power adapter to power the ReachNXT 100-8t when using the SFP uplink.

2Set the ReachNXT 100-8t in its installed location, such as on a table in a conference room.

To use the optional magnet mounting kit to install the ReachNXT 100-8t in a fixed location, follow

the procedure under “Using the Magnet Mounting Kit”.

3To secure the ReachNXT 100-8t in its location using a Kensington lock, follow the instructions

provided with the Kensington lock.

Insert the locking device into the Kensington lock slot on the ReachNXT 100-8t rear panel (Figure 1),

then turn it in the locking direction.

Figure 1: Kensington Lock Slot on the ReachNXT 100-8t Rear Panel

4If the ReachNXT 100-8t will be powered using AC power, connect the optional AC adapter to the

power socket on the ReachNXT 100-8t (labeled PWR), and plug the AC adapter into a wall outlet.

Using the Magnet Mounting Kit

The optional magnet mounting kit allows you to mount the ReachNXT 100-8t in a fixed location using

magnets attached to the switch. The magnet mounting kit contains the following items:

●Two magnets

●Two rubber stabilizing pads

●Mounting plate

●Screws and anchors

The magnets are attached to two slots on the bottom of the ReachNXT 100-8t unit (Figure 1). At the

other two corners, rubber stabilizing pads prevent the unit from rocking.

Kensington lock slot

RCH_006

ReachNXT™100-8t Quick Start Guide 3

Figure 2: Magnet Slots on the ReachNXT 100-8t Bottom Panel

To use the magnet mounting kit:

1If the ReachNXT 100-8t will be mounted on a non-metallic surface, attach the mounting plate to the

installation location, using the supplied screws and anchors.

2Attach the magnets to the bottom panel of the ReachNXT 100-8t, as follows:

aOn each magnet, twist the mounting tab counter-clockwise two full turns (see Figure 3).

aInsert the tab on the magnet into a magnet slot on the ReachNXT 100-8t. and slide the magnet in

the direction of the narrow end of the tab.

bTurn the magnet clockwise until it is finger tight to secure it to the ReachNXT 100-8t.

Figure 3: Attaching Magnets

3After the magnets are installed, attach a rubber stabilizing pad at each corner where a magnet is not

installed.

4Set the ReachNXT 100-8t in the installation location, with the magnets touching either the metallic

surface or the mounting plate.

To remove the ReachNXT 100-8t from its installed location, slide the unit off the plate or other metallic

surface. Do not pull the unit away from the plate.

Magnet slots

RCH_001

Rubber pad

positions

RCH_002

ReachNXT™100-8t Quick Start Guide

Configuring the ExtremeXOS Switch Software

To initialize the ReachNXT 100-8t, perform the following steps on the uplinked ExtremeXOS switch:

1If the ReachNXT 100-8t will be powered using Power over Ethernet (PoE) from the uplinked

ExtremeXOS switch, configure PoE on the uplinked switch, using the following commands:

●enable inline-power (enabled by default)

●show inline-power

●configure inline-power

For more information about configuring PoE, refer to the ExtremeXOS Concepts Guide.

2Enable LLDP for the port to which the ReachNXT 100-8t will be connected. Use the following

command to enable LLDP:

enable lldp ports [all | <port_list>]

3Connect the ReachNXT 100-8t uplink port (port 9 or 9x) to the uplinked ExtremeXOS switch.

This step initializes the ReachNXT 100-8t. When initialization is complete, and the uplinked

ExtremeXOS switch is detected, the MGMT LED on the ReachNXT 100-8t lights solid green.

4To verify that the uplinked ExtremeXOS switch detects the ReachNXT 100-8t, enter the following

command on the uplinked switch:

show lldp neighbors detailed

For an LLDP neighbor that is a ReachNXT 100-8t, the command output is similar to the following:

# show lldp neighbors detailed

--------------------------------------------------------------------------

LLDP Port 4:1 detected 1 neighbor

Neighbor: 00:04:96:1F:A8:00/9, age 29 seconds

- Chassis ID type: MAC address (4)

Chassis ID : 00:04:96:1F:A8:00

- Port ID type: ifName (5)

Port ID : "9"

- Time To Live: 120 seconds

- System Name: "Reach 100-8t 800284-00-01 0840G-00560"

- System Description: "Reach 100-8t 1.6.1.6"

NOTE

To function, the ReachNXT 100-8t must be connected to an ExtremeXOS switch. The ReachNXT 100-8t only

operates when it detects an ExtremeXOS switch connected to the uplink port via LLDP. LLDP must be enabled on

the ExtremeXOS switch to which the ReachNXT 100-8t is connected. The ReachNXT 100-8t disables its user ports

if no ExtremeXOS switch is detected, or the uplink port is down. The user ports are re-enabled when the uplink port

is up, and an ExtremeXOS switch is detected.

Otros manuales para ReachNXT 100-8t

Tabla de contenidos

Otros manuales de Cambiar de Extreme Networks

Extreme Networks

Extreme Networks Summit X650-24x Guía de referencia

Extreme Networks

Extreme Networks Summit 300-48 Guía de seguridad

Extreme Networks

Extreme Networks ExtremeSwitching Virtual Services Platform... Manual de usuario

Extreme Networks

Extreme Networks ExtremeSwitching X440-G2 Series Manual

Extreme Networks

Extreme Networks Summit X250e-24p Guía de referencia

Extreme Networks

Extreme Networks ExtremeSwitching VDX 6740 Manual

Extreme Networks

Extreme Networks BlackDiamond 10808 Manual de usuario

Extreme Networks

Extreme Networks BlackDiamond X8 Series Instrucciones de montaje

Extreme Networks

Extreme Networks Summit X150 Series Manual

Extreme Networks

Extreme Networks ExtremeSwitching 3600 Series Manual de usuario

Extreme Networks

Extreme Networks Summit X150 Series Manual

Extreme Networks

Extreme Networks EAS 100-24t Switch Manual de usuario

Extreme Networks

Extreme Networks 7720 Manual de usuario

Extreme Networks

Extreme Networks Summit X150 Series Manual de usuario

Extreme Networks

Extreme Networks BlackDiamond 8800 Series Manual de usuario

Extreme Networks

Extreme Networks BlackDiamond 6800 Manual

Extreme Networks

Extreme Networks BlackDiamond X8 Series Manual

Extreme Networks

Extreme Networks Summit X460-24t Manual de usuario

Extreme Networks

Extreme Networks Summit X670-G2 Series Manual de instalación y operación

Extreme Networks

Extreme Networks ExtremeSwitching 5520 Series Manual

Extreme Networks

Extreme Networks ExtremeSwitching ISW Series Manual de usuario

Extreme Networks

Extreme Networks ExtremeSwitching 5420 Series Manual

Extreme Networks

Extreme Networks Summit WM200 Manual de usuario

Extreme Networks

Extreme Networks 3626 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario