Extech Instruments RPM250W Manual de usuario

User Manual

RPM250W Laser Tachometer

Bluetooth® Connectivity with the ExView® Mobile App

Table of contents

1 Introduction........................................................................1

2 Safety ................................................................................2

3 FCC Compliance .................................................................3

4 Product Description ............................................................4

4.1 Meter Parts ...............................................................4

4.2 Function Buttons ........................................................ 4

4.3 Display Symbols.........................................................5

5 Operation...........................................................................6

5.1 Powering the Meter ..................................................... 6

5.2 Auto Power Off (APO)..................................................6

5.3 Tachometer (RPM) Measurements .................................6

5.4 Counter Measurements (with illuminated objects) ..............7

5.5 Counter Measurements (with external illumination) ............7

5.6 Data Hold Function .....................................................8

5.7 LCD Backlight............................................................ 8

5.8 MAX/MIN Readings in RPM Mode..................................8

5.9 Bluetooth Operation ....................................................8

6 Maintenance.......................................................................9

6.1 General Cleaning .......................................................9

6.2 Battery Replacement...................................................9

7 Specifications................................................................... 10

7.1 General Specifications............................................... 10

7.2 Measurement Specifications ....................................... 10

7.3 Environmental Specifications ...................................... 10

7.4 Connectivity Specifications ......................................... 11

8 Two-year Warranty............................................................. 12

8.1 Calibration and Repair Services................................... 12

8.2 Contact Customer Support ......................................... 12

#NAS100078; r. AA/78959/78963; en-US ii

Introduction

Thank you for selecting the Extech RPM250W Laser Tachometer. This meter

measures rotations per minute on equipment such as fan blades, rotors, tur-

bines, and similar machinery. The RPM250W is also a counter where items

on a conveyor, for example, can be counted. Measurements are made using

the built-in photo-electric sensor, situated at the top of the meter. Readings

are shown on the backlit LCD.

The meter includes Bluetooth connectivity, MAX/MIN memory (in RPM mode),

auto power off, data hold, Laser pointer, backlit LCD, and tripod mount.

Using the Extech ExView mobile app, you can pair your smart devices with

the meter using Bluetooth. The app and the W Series meters were developed

together for seamless integration. Download the free app from the App Store

(iOS®) or from Google Play (Android™).

This quality instrument is designed to provide years of reliable service, high

accuracy and simple operation. Please visit the Extech website for additional

information and world-class support.

#NAS100078; r. AA/78959/78963; en-US 1

Safety

Please read all safety information before using this device

CAUTION

• Check for damage to the device’s housing, sensor, display, and battery compartment

before use. If obvious damage or abnormalities are noticed, please discontinue use

and return the device for service.

• Do not attempt to open the meter housing or access the sensor module. There are no

user-serviceable components in this device.

• Do not point the Laser beam toward the eyes. See Laser safety label below:

• Replace the batteries immediately after the low battery symbol appears. If the device is

to be stored for a period of months, please remove the batteries and store separately.

• Do not store the device in high temperature or humidity environments, in flammable or

combustible areas, or where a strong electromagnetic field is present.

• This device is CE certified.

#NAS100078; r. AA/78959/78963; en-US 2

FCC Compliance

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

WARNING

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

#NAS100078; r. AA/78959/78963; en-US 3

Product Description

4.1 Meter Parts

1. Photo-electric sensor and Laser pointer lens

2. Backlit LCD (detailed below)

3. Function buttons (detailed below)

4. Tripod mount

5. Battery compartment

4.2 Function Buttons

Power / Bluetooth button

Long press to switch the device on. Short press to switch off.

With the meter powered, long press to switch Bluetooth on/off.

Short press to switch the meter off directly from the Bluetooth mode.

MAX/MIN and Counter Reset button

In RPM mode, short press to view the MAX/MIN readings; Long press to

clear the readings.

In Count mode, short press to reset the count to zero. The COUNT dis-

play text will flash twice.

Data Hold / Backlight button

Short press to freeze/unfreeze the displayed reading. HOLD will display

when data hold is active.

Long press to switch the LCD backlight on/off.

#NAS100078; r. AA/78959/78963; en-US 4

Product Description

Tachometer/Counter and Laser button

Short press to toggle Tachometer (RPM) and Count modes.

Long press to switch the Laser pointer on/off. The Laser pointer symbol

is shown when the Laser is on.

APO ON/OFF With the meter on, long press the power and Hbuttons to switch APO

on/off. The APO symbol is displayed when APO is enabled. APO is

reset each time the meter power is cycled.

4.3 Display Symbols

1. Tachometer/Counter readings

2. Laser pointer symbol

3. Monitor symbol appears when the sensor detects a reflection from the

supplied tape or when an object is counted

4. Data Hold mode

5. Maximum reading

6. Minimum reading

7. Low battery symbol

8. Auto Power Off (APO) symbol

9. Bluetooth active

10. Tachometer (RPM) and Counter (COUNT) modes

#NAS100078; r. AA/78959/78963; en-US 5

Operation

5.1 Powering the Meter

The meter operates on three (3) 1.5 V (AAA) batteries, installed in the rear

compartment.

Long press the power button to switch the meter on. Short press the power

button to switch the meter off. If the meter does not switch on, check the bat-

teries for proper orientation.

When the low battery symbol appears on the display, replace the batteries

immediately to ensure accurate readings.

5.2 Auto Power Off (APO)

The meter switches off automatically five (5) minutes after the last button

press.

The default mode for APO is ON (the APO symbol on the display indicates

that APO is enabled).

To switch the APO function off, with the meter switched on, long press the

power and Hbuttons. The APO symbol will switch off, indicating that the

function is disabled. APO is reset each time the meter’s power is cycled.

Repeat this process to switch APO back on manually.

5.3 Tachometer (RPM) Measurements

WARNING

To avoid personal injury and damage to the meter and other machinery, keep a distance of

at least 50 mm (2 in.) between the tachometer and the measured object.

1. Switch off the device under test so that it is not moving.

2. Cut off a 0.5 x 0.5 in. (12 mm x 12 mm) piece of reflective tape (supplied)

and affix it to the device under test.

3. Long press the power button to switch the meter on and short press the

mode button (if necessary) so that RPM is shown.

4. Switch on the device under test so that it begins moving.

5. From a distance of 2 to 20 in. (50 to 500 mm), point the meter’s sensor

(top) towards the reflective tape. For best results, the vertical angle of inci-

dence should be < 30°.

#NAS100078; r. AA/78959/78963; en-US 6

Operation

6. When the sensor detects a reflection from the tape, the monitor symbol

appears on the LCD.

7. The five-digit LCD read-out shows the RPM measurement.

8. If the measurement is > 99,999 RPM, OL will appear on the display in

place of a reading.

NOTE

When measuring < 50 RPM, the period of the pulse is quite long and requires that the meter

be kept still to ensure accuracy. Wait at least two pulse signals for the best accuracy. If the

pulse is longer than 7 seconds, the RPM reading will not change.

5.4 Counter Measurements (with illuminated objects)

1. Long press the power button to switch the meter on.

2. Short press the mode button so that COUNT is displayed.

3. Position the meter 2 to 20 in. (50 to 500 mm) from the object under test.

For best results, the vertical angle of incidence should be < 30°.

4. Switch on the machinery under test so that it begins moving.

5. Each time an illuminated object passes the meter sensor, the count incre-

ments by 1 and the monitor symbol appears.

6. Short press the MAX/MIN button to reset the counter to zero (COUNT will

flash twice).

7. When the counter is > 99,999 units, OL will display.

5.5 Counter Measurements (with external illumination)

1. Long press the power button to switch the meter on.

2. Short press the mode button so that COUNT is displayed.

3. Long press the Laser button to switch off the Laser.

4. Position the meter 2 to 20 in. (50 to 500 mm) from the object under test.

For best results, the vertical angle of incidence should be no greater than

30°.

5. Position the external optical source opposite the meter, on the other side

of the device under test (so the device under test is situated between the

meter and the light source).

6. Switch on the device under test so that it begins moving.

7. As each object passes between the meter sensor and the optical source,

the count increments by 1 and the monitor symbol appears.

8. Short press MAX/MIN to reset the counter to zero (COUNT will flash

twice).

9. If the count > 99,999, the display will show OL in place of a reading.

#NAS100078; r. AA/78959/78963; en-US 7

Operation

5.6 Data Hold Function

Short press the Data Hold (H) button to freeze/unfreeze the displayed read-

ings. While Data Hold is active, HOLD will appear on the LCD.

5.7 LCD Backlight

Long press the backlight button to switch the display backlight on or off.

Excessive use of the backlight will shorten battery life.

5.8 MAX/MIN Readings in RPM Mode

In RPM mode, short press the MAX/MIN button to step through the MAX/MIN

memories.

To clear the memory, long press the MAX/MIN button while either the MAX or

the MIN mode text is showing. The memories are cleared each time the meter

power is cycled.

5.9 Bluetooth Operation

Long press the Bluetooth button with the meter on, to switch Bluetooth on

or off. This communication symbol is shown when Bluetooth is on.

The Bluetooth utility allows you to remotely monitor readings on an iOS or An-

droid smart device using the Extech ExView mobile app designed for use with

this meter.

Download the ExView mobile app from the App Store for iOS devices or from

Google Play for Android devices. Instructions for mobile app use are available

from the ExView product page on the Extech website (link below).

http://www.extech.com

Switch APO off when using Bluetooth by pressing and holding the power

and Hbuttons for 2 seconds (the APO symbol will switch off). This will pre-

vent the meter from automatically switching off while you are logging data or

monitoring readings in real time on your smart device.

#NAS100078; r. AA/78959/78963; en-US 8

Otros manuales para RPM250W

Tabla de contenidos

Otros manuales de Instrumento de medición de Extech Instruments

Extech Instruments

Extech Instruments MW12 Manual de usuario

Extech Instruments

Extech Instruments BT100 Manual de usuario

Extech Instruments

Extech Instruments SDL470 Manual de usuario

Extech Instruments

Extech Instruments 380801 Manual de usuario

Extech Instruments

Extech Instruments RPM33-NIST Manual de usuario

Extech Instruments

Extech Instruments VB450 Manual de usuario

Extech Instruments

Extech Instruments RH520B Manual de usuario

Extech Instruments

Extech Instruments SDL100 Manual de usuario

Extech Instruments

Extech Instruments DO210 Manual de usuario

Extech Instruments

Extech Instruments 407495 Manual de usuario

Extech Instruments

Extech Instruments MA610 Manual de usuario

Extech Instruments

Extech Instruments VT30-E Manual de usuario

Extech Instruments

Extech Instruments 38389 Manual de usuario

Extech Instruments

Extech Instruments MA430T Manual de usuario

Extech Instruments

Extech Instruments EC150 Manual de usuario

Extech Instruments

Extech Instruments MF100 Manual de usuario

Extech Instruments

Extech Instruments 407227 Manual de usuario

Extech Instruments

Extech Instruments 475055 Manual de usuario

Extech Instruments

Extech Instruments PH210 Manual de usuario

Extech Instruments

Extech Instruments CO250 Manual de usuario

Extech Instruments

Extech Instruments HD780 Manual de usuario

Extech Instruments

Extech Instruments CT-3060 Manual de usuario

Extech Instruments

Extech Instruments EA80 Manual de usuario

Extech Instruments

Extech Instruments SDL150 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario