Extech Instruments ExStik RE300 Manual de usuario

User Guide

ExStikTM Model RE300

Waterproof ORP Meter

RE300-en-GB_V4.5 8/16

ExStikTM Description

Front Panel Controls

1. Battery compartment cap

2. LCD Display

3. MODE button

4. CAL button (unused on RE300)

5. ON/OFF button

6. Electrode collar

7. Electrode

(Electrode cap is not shown)

Display Description

1. Reading

2. Units

3. Bargraph

4. Data Hold

5. Scale

6. Low Battery

RE300-en-GB_V4.5 8/16

Operation

Getting Started

Battery Activation: An insulating tab is located in the battery compartment and prevents battery drain

during storage. It must be removed before use.

White KCL crystals may be present on the electrode. These crystals will dissolve in a distilled water

soak or they can be simply rinsed with tap water.

Do NOT wipe the end of the RE300 electrode as it may damage the sensor.

When the RE300 is turned on, it enters the Automatic Calibration mode. ‘SELF’ and ‘CAL’ will appear

on the LCD while calibration is in progress. After the calibration is complete, ‘SELF’ and ‘CAL’ will

extinguish and both the main display and bargraph will read ORP in mV units. The bargraph will read

0mV (far left), 500mV (center), and 1000mV (far right).

ORP Testing

1. Remove cap from the electrode and soak the electrode in distilled or tap water for 10 minutes.

2. Press the ON/OFF button to switch the RE300 on.

3. Dip the electrode1/2” to 1” into the test solution. Stir once and let the reading stabilize for 1 to 3

minutes.

4. Note the ORP or press MODE to freeze the reading The HOLD display icon will appear along

with the held reading. The held reading will be stored in the next 15-reading storage location

(see below). Press the MODE key to return to normal operation.

5. Press the ON/OFF button to turn the RE300 off. If you do not press a button for 10 minutes the

RE300 shuts off automatically.

15-Reading Measurement Storage

1. Press the MODE button to store a reading. The LCD will briefly display the memory location

number and then the value stored (Data Hold will activate).

2. Press MODE again to return to normal operation.

Repeat step 1 above to store the next reading and so

on.

3. If an attempt is made to store more than 15 readings,

the stored readings (starting with the first reading) will

be overwritten.

Recalling Stored Readings

Note: First ensure that the HOLD symbol is not displayed. If it is, exit the HOLD function by pressing

the MODE button.

1. Press the CAL button once and then press the MODE button immediately after CAL is

displayed; the location number (1 through 15) will flash. If the CAL mode is accidentally

accessed (display flashing), press the CAL button again to exit.

2. The last stored reading taken will be displayed first. To advance through the stored readings,

press the MODE button. The location number is displayed first, followed by the reading stored

in that location.

3. To exit the storage mode, press the CAL button and the ExStikTM will return to normal

operation.

RE300-en-GB_V4.5 8/16

Measurement and Display Considerations

If the unit appears to be locked (display frozen). It is possible that the Data Hold mode has

been inadvertently accessed by pressing the MODE button. Simply press the MODE button

again or turn the meter off and restart if the display appears frozen.

If the meter does latch up and no button presses revive it, remove the batteries and restart.

Note that if the batteries are removed, any stored readings will be discarded. Factory

calibration data for all models will be retained, however.

Replacing the Electrode

To preserve Electrode life, keep the sponge in the protective cap soaked with

distilled or tap water when not in use (store vertically).

DO NOT USE DE-IONIZED WATER.

1. To remove an electrode, unscrew and completely remove the electrode collar (turn the collar

counter-clockwise to remove).

2. Gently rock the electrode from side to side, pulling it downwards, until it disconnects from the

meter.

3. To attach an electrode, carefully plug the electrode into the meter socket (note that the

electrode connector is keyed, ensuring proper connection).

4. Tighten the electrode collar firmly enough to make a good seal (a rubber gasket seals the

electrode with the meter).

Powering the ExStik™

The ExStikTM uses four (4) CR2032 batteries (included). If the batteries are weak, the ‘BAT’

indicator appears on the LCD. Press the ON/OFF key to turn the ExStikTM on or off. The auto

power off feature shuts the ExStikTM off automatically after 10 minutes of inactivity to preserve

battery life.

Accuracy check of the RE300 electrode

1. Remove cap from the electrode and press the ON/OFF button to switch the RE300 on.

2. Dip the electrode1/2” to 1” into the ORP Standard test solution. Stir once and let the reading

stabilize for 1 to 3 minutes.

3. The measurement should be within +/- 4mV of the ORP Standard.

RE300-en-GB_V4.5 8/16

Battery Replacement

1. Twist off the battery compartment cap

2. Replace the four (4) 2032 batteries observing polarity.

3. Replace the battery compartment cap



Neverdisposeofusedbatteriesorrechargeablebatteriesinhouseholdwaste.

Asconsumers,usersarelegallyrequiredtotakeusedbatteriestoappropriate

collectionsites,theretailstorewherethebatterieswerepurchased,orwherever

batteriesaresold.

Disposal:Donotdisposeofthisinstrumentinhouseholdwaste.Theuserisobligatedtotakeend‐

of‐lifedevicestoadesignatedcollectionpointforthedisposalofelectricalandelectronic

equipment.

Optional Accessories

Replacement ORP electrode (Part Number: RE305)

Specifications

Display Multifunction LCD with Bargraph

Operating conditions 0 to 50oC (32 to 122oF) / < 80% RH

RP Range / Accuracy ± 999mV / ± 4mV

Electrode Platinum with silver wire in KCL

Electrode Compensation 204.6mV

Measurement storage 15 tagged (numbered) readings

Power Four (4) CR2032 button batteries

Low battery indication ‘BAT’ appears on the LCD

Auto power off After 10 minutes of inactivity

Dimensions 35,6x172,7x40,6mm (1,4x6,8x1,6”); 110g (3,85oz)



Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

ISO‐9001Certified

www.extech.com

Tabla de contenidos

Otros manuales de Instrumento de medición de Extech Instruments

Extech Instruments

Extech Instruments 380801 Manual de usuario

Extech Instruments

Extech Instruments 380976-K Manual de usuario

Extech Instruments

Extech Instruments 380560 Manual de usuario

Extech Instruments

Extech Instruments GX900 Manual de usuario

Extech Instruments

Extech Instruments 461750 Manual de usuario

Extech Instruments

Extech Instruments 407738 Manual de usuario

Extech Instruments

Extech Instruments 382400 Manual de usuario

Extech Instruments

Extech Instruments PQ3450 Manual de usuario

Extech Instruments

Extech Instruments HD450 Manual de usuario

Extech Instruments

Extech Instruments 45160 Manual de usuario

Extech Instruments

Extech Instruments AN310-NIST Manual de usuario

Extech Instruments

Extech Instruments 38394 Manual de usuario

Extech Instruments

Extech Instruments 461920 Manual de usuario

Extech Instruments

Extech Instruments LT250W Manual de usuario

Extech Instruments

Extech Instruments PQ34-12 Manual de usuario

Extech Instruments

Extech Instruments UV505 Manual de usuario

Extech Instruments

Extech Instruments AN250W Manual de usuario

Extech Instruments

Extech Instruments RH300 Manual de usuario

Extech Instruments

Extech Instruments AN310 Manual de usuario

Extech Instruments

Extech Instruments RPM33 Manual de usuario

Extech Instruments

Extech Instruments 451112 Manual de usuario

Extech Instruments

Extech Instruments MO220 Manual de usuario

Extech Instruments

Extech Instruments 380801 Manual de usuario

Extech Instruments

Extech Instruments LT40 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario