Extech Instruments 380942 Manual de usuario

User’s Guide

Model 380942

True RMS AC/DC 30A Mini Clamp-on Meter

380942-EU-EN-V2.1-4/11

Introduction

Congratulations on your purchase of the Extech Model 380942 DC/AC Clamp Meter. This meter is

shipped fully tested and calibrated and, with proper use, will provide years of reliable service.

Meter Description

1. Current sense jaw

2. Measurement Trigger

3. Function switch

4. Data HOLD key

5. MAX / MIN key

6. One-touch DCA ZERO key

7. LCD Display

8. Positive input terminal for Voltage

9. COM terminal

Safety Symbols and Information

!Caution ! Refer to the explanation in this Manual

Caution ! Risk of electric shock

Earth (Ground)

This meter has been designed to be safe in use, but the operator must use caution in its operation.

The rules listed below should be carefully followed for safe operation.

1. NEVER apply voltage or current to the meter that exceeds the specified maximum:

2. USE EXTREME CAUTION when working with high voltages.

3. DO NOT measure voltage if the voltage on the "COM" input jack exceeds 600V above earth

ground.

4. ALWAYS turn off the power and disconnect the test leads before opening the back to replace

the fuse or batteries.

5. NEVER operate the meter unless the back cover and the battery/fuse door are in place and

fastened securely.

380942-EU-EN-V2.1-4/11

Operation

AC Current Measurements (True RMS)

WARNING: To avoid electric shock, disconnect the test leads from the meter before making current

measurements.

1) Set the Function switch to the 400mA, 4000mA, or 30A AC range.

2) Press the jaw trigger and clamp around, fully enclosing a single conductor.

Do not allow a gap between the two halves of the jaw. Refer to the diagram

at right for the correct way to enclose a single conductor.

3) Read the AC Current value on the LCD’s digital or bargraph display.

DC Current Measurements

WARNING: To avoid electric shock, disconnect the test leads from the meter before making current

measurements.

1) Set the Function switch to the mA or 30A DC range.

2) Press the DCA zero key to null the meter display.

3) Press the Trigger to open the current sense Jaw.

4) Fully enclose the conductor to be measured. Do not allow a gap between the two halves of the

jaw.

5) Read the DC Current value on the LCD’s digital or bargraph display.

AC Voltage Measurements (True RMS)

WARNING: To avoid electric shock or damage to the meter, do not make any voltage

measurements that exceed the maximum specified limits.

1) Set the Function switch to the 400V AC position.

2) Insert the test leads to the meter as follows: Red lead to “V” terminal; Black lead to the COM

input.

3) Connect the test leads to the circuit or device under test.

4) Read the AC Voltage value on the LCD’s digital or bargraph display.

DC Voltage Measurements

WARNING: To avoid electric shock or damage to the meter, do not make any voltage

measurements that exceed the maximum specified limits.

1) Set the Function switch to the 400V DC position.

2) Insert the test leads to the meter as follows: Red lead to “V” terminal; Black lead to the COM

input.

3) Connect the test leads to the circuit or device under test.

4) Read the DC Voltage value on the LCD’s digital or bargraph display.

Yes

380942-EU-EN-V2.1-4/11

Advanced Features

Relative Measurements

1) Press the ZERO key. The displayed reading will zero and the word ZERO will appear on the

upper portion of the LCD.

2) All subsequent measurements will now be displayed with respect to the zeroed reading. For

example, if a 20A reading is zeroed and a 30A reading is subsequently measured, the LCD will

display 10A.

3) To return to normal operation, press and hold the ZERO key for 2 seconds until the word ZERO

switches off.

4) Note that Relative mode is not available if MIN/MAX mode is enabled.

Data Hold

To freeze the current reading on the LCD, press the Data Hold key. The word HOLD will appear on

the LCD while the meter is in the Data Hold mode. To release the Data Hold function and return the

meter to normal operation, press the Data Hold key again. The word HOLD will switch off.

MIN/MAX Readings

Pressing the MIN/MAX key allows the meter to display the highest and then the lowest readings

encountered. Press the MIN/MAX key once to view the minimum reading, press it again to view the

maximum reading. Note that the meter will only change its displayed reading when a measurement

is taken higher than the previous MAX or lower than the previous MIN readings. The HOLD display

icon (along with the MIN or MAX icon) will appear on the LCD in MIN/MAX mode. Pressing the

MIN/MAX key a 3rd time returns the meter to normal operation.

Auto Power Off

To extend battery life, the meter will auto power off after 30 minutes of operation. To resume

operation, either turn the meter OFF and then ON again, or press the HOLD button. To disable the

auto power off function, press down the “HOLD” key while turning the meter on.

380942-EU-EN-V2.1-4/11

Maintenance

Battery Replacement

1) When the low battery symbol appears on the LCD the batteries must be replaced.

2) Turn the meter OFF and remove the rear battery compartment Phillips screw.

3) Lift off the battery compartment cover and replace the two 1.5V AA batteries.

4) Replace the compartment cover and secure the screw.

You, as the end user, are legally bound (EU Battery ordinance) to return all used

batteries, disposal in the household garbage is prohibited! You can hand over your

used batteries / accumulators at collection points in your community or wherever batteries /

accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

Cleaning

Caution: Use only a dry cloth to clean the plastic case.

Specifications

General Specifications

Display 3-3/4 digit (4000 count) LCD with 40 segment bargraph

Functions ACA, DCA, ACV, DCV

Polarity Minus sign ( - ) indicates negative polarity

Current sensor Hall effect sensor type

Overload indication Left blinking digit

DCA zero adjust One touch zero key

Display rate 2 readings/second (20 readings/second for bargraph)

Battery Two 1.5V AA batteries

Operating conditions -10oC to 50oC (4oF to 122oF); < 85% Relative Humidity

Storage conditions -20oC to 60oC (- 4oF to 140oF); < 75% Relative Humidity

Altitude Operate at less than 2000 meters (for indoor use only)

Power consumption Approximately 10mA DC

Weight 190g (6.2 oz.) including battery

Dimensions 183 x 63.6 x 35.6mm (7.2 x 2.5 x 1.4”) (H x W x D)

Jaw opening 23mm (0.9”)

Standards IEC 1010 Category III 300V, Category II 600V

Range Specifications

Function Range Resolution Accuracy Overload

protect

CDA04Am1Am0004DC Current

30A 10mA

± (2.0% + 3d)

100A DC

50/60Hz 40 to 100Hz

400mA 0.1mA ±(1.5% + 5d) ±(2.0% + 5d) 40A AC

50/60Hz 40 to 1kHz

4000mA 1mA ±(2.5% + 5d) ±(3.0% + 5d) 40A AC

AC Current

(True RMS)

30A 10mA ±(2.0% + 5d) ±(2.5% + 5d) 100A AC

DC Voltage 400V 0.1V ± (1.0% + 2d) 1000V DC

50/60Hz 40 to 1kHzAC Voltage

(True RMS) 400V 0.1V ±(1.5% + 4d) ±(2.0% + 5d) 800V AC

Specification Notes

•AC Voltage and Current Crest Factor: < 3

•AC / DC Voltage Input Impedance: 10MΩ

www.extech.com

more infor for Extech 380942

Phone: 01235 838 555

Email: cs@airconcern.co.uk

Web. www.airconcern.co.uk

Air Concern Ltd, Building 173 Curie Avenue Harvell Didcot, Oxfordshire

Tabla de contenidos

Otros manuales de Instrumento de medición de Extech Instruments

Extech Instruments

Extech Instruments 401027 Manual de usuario

Extech Instruments

Extech Instruments 45168CP Manual de usuario

Extech Instruments

Extech Instruments 380801 Manual de usuario

Extech Instruments

Extech Instruments NON-DISPLAY PORTABLE Manual de usuario

Extech Instruments

Extech Instruments RPM250W Manual de usuario

Extech Instruments

Extech Instruments 461893 Manual de usuario

Extech Instruments

Extech Instruments EA80 Manual de usuario

Extech Instruments

Extech Instruments HT200 Manual de usuario

Extech Instruments

Extech Instruments AN310 Manual de usuario

Extech Instruments

Extech Instruments 401025 Manual de usuario

Extech Instruments

Extech Instruments Oyster-10 Manual de usuario

Extech Instruments

Extech Instruments 421509 Manual de usuario

Extech Instruments

Extech Instruments AN10 Manual de usuario

Extech Instruments

Extech Instruments GRT350 Manual de usuario

Extech Instruments

Extech Instruments 461891 Manual de usuario

Extech Instruments

Extech Instruments 407780A Manual de usuario

Extech Instruments

Extech Instruments MA410T Manual de usuario

Extech Instruments

Extech Instruments LT45 Manual de usuario

Extech Instruments

Extech Instruments MO220 Manual de usuario

Extech Instruments

Extech Instruments 401036 Manual de usuario

Extech Instruments

Extech Instruments AN200 Manual de usuario

Extech Instruments

Extech Instruments 433201A Manual de usuario

Extech Instruments

Extech Instruments MA130 Manual de usuario

Extech Instruments

Extech Instruments RH600 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario