Evertz 7700DA7-HD Manual de usuario

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Revision 1.1

TABLE OF CONTENTS

1. OVERVIEW ............................................................................................................................................ 1

2. INSTALLATION ..................................................................................................................................... 2

3. SPECIFICATIONS.................................................................................................................................. 3

3.1. SERIAL VIDEO INPUT ................................................................................................................ 3

3.2. SERIAL VIDEO OUTPUTS.......................................................................................................... 3

3.3. ELECTRICAL............................................................................................................................... 3

3.4. PHYSICAL ................................................................................................................................... 3

4. STATUS LEDS....................................................................................................................................... 4

5. JUMPERS AND USER ADJUSTMENTS............................................................................................... 5

5.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED

BY THE GLOBAL FRAME STATUS........................................................................................... 5

5.2. SELECTING WHETHER MODULE WILL BE CONTROLLED FROM THE

LOCAL CONTROLS OR THROUGH THE VISTALINK

INTERFACE......................................... 5

5.3. SELECTING THE RECLOCKING RATE..................................................................................... 6

5.4. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES................................................. 6

6. VISTALINK

REMOTE MONITORING/CONTROL................................................................................ 7

6.1. WHAT IS VISTALINK

?................................................................................................................ 7

6.2. VISTALINK

MONITORED PARAMETERS ................................................................................. 7

6.3. VISTALINK

CONTROLLED PARAMETERS .............................................................................. 8

6.4. VISTALINK

TRAPS ..................................................................................................................... 8

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Revision 1.1

Figures

Figure 1-1: 7700DA7-HD Block Diagram............................................................................................. 1

Figure 2-1: 7700DA7-HD Rear IO Module...........................................................................................2

Figure 5-1: LED and Jumper Locations............................................................................................... 5

Tables

Table 6-1: VistaLINK

Monitored Parameters...................................................................................... 7

Table 6-2: VistaLINK

Controlled Parameters..................................................................................... 8

Table 6-3: VistaLINK

Traps................................................................................................................ 8

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Revision 1.1

REVISION HISTORY

REVISION DESCRIPTION DATE

1.0 Original Version Jun 05

1.1 Updated rear plate drawing. Updated VistaLINK section. General cleanup. Feb 09

Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for

the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of

Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The only warranty offered

by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.

Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is

granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation.

Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If you encounter an error,

please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in equipment design or

specifications.

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Revision 1.1

This page left intentionally blank

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Revision 1.1 Page-1

1. OVERVIEW

The 7700DA7-HD Reclocking Distribution Amplifier provides reliable distribution of your 1.5 Gb/s HDTV

and 143 Mb/s to 540 Mb/s standard definition serial digital video signals. The 7700DA7-HD features one

auto-equalized input with seven reclocked outputs. The 7700DA7-HD has been designed to reclock at 1.5

Gb/s and 143 Mb/s to 540 Mb/s. In non-reclocking mode it can be used as a distribution product for

SMPTE 310M (19.4 Mb/s) and all rates up to 1.5 Gb/s.

The 7700DA7-HD occupies one card slot in the 3 RU frame, which will hold up to 15 modules or the 1RU

frame, which will hold up to three modules.

Features:

•Reclocking mode for SMPTE 292M (1.5 Gb/s), SMPTE 259M (143 to 360 Mb/s), SMPTE 344M

(540 Mb/s) or DVB-ASI signals - auto detects correct bitrate

•Non-reclocking mode for signals from 19.4 Mb/s (SMPTE 310M) up to 1.5 Gb/s

•Fully hot-swappable from front of frame with no BNC disconnect required

•Independent isolated output drivers to ensure no cross channel loading effects (i.e. no need to

terminate unused outputs)

•Outputs maintain polarity from input to output for DVB-ASI applications

•Tally output on Frame Status bus upon loss of input signal for quality monitoring

•VistaLINK

- enabled offering remote monitoring, control and configuration capabilities via SNMP.

VistaLINK

is available when modules are used with the 3RU 7700FR-C frame and a 7700FC

VistaLINK

Frame Controller module in slot 1 of the frame using the model 9000NCP Network Control

Panel or Evertz VistaLINK

PRO or other third party SNMP manager software.

Equalizer

Serial Input

(19.4 Mb/s or

143 - 540 Mb/s or

1,5 Gb/s)

Reclocker Bypass

143-540Mb/s & 1.5 Gb/s

Reclocker

Cable Driver Array

143 177 270 360 540

Control &

Indicators

Module

Health

7 Reclocked

Serial Outputs

(19.4 Mb/s or

143 - 540 Mb/s or

1,5 Gb/s)

VistaLINK

Interface

1.5G

Figure 1-1: 7700DA7-HD Block Diagram

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Page-2 Revision 1.1

2. INSTALLATION

The 7700DA7-HD comes with a companion rear plate that occupies one slot in the frame. For information

on inserting the module into the frame see the 7700FR chapter section 3.

Figure 2-1: 7700DA7-HD Rear IO Module

SDI INPUT: Input BNC connector for 10-bit serial digital video signals compatible with the

SMPTE 292M, SMPTE 259M, DVB-ASI or SMPTE 310M standard. See section 5.2

for information on choosing the correct video standard.

SDI OUTPUT: There are seven BNC connectors with reclocked serial component video outputs,

compatible with the SMPTE 292M, SMPTE 259M / DVB-ASI, or SMPTE 310M

standard.

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Revision 1.1 Page-3

3. SPECIFICATIONS

3.1. SERIAL VIDEO INPUT

Standards:

Reclocking Mode: SMPTE 292M SMPTE 259M A, B, C, D (143 to 360 Mb/s),

SMPTE 344M (540 Mb/s) DVB-ASI, or M2S

Non reclocking Mode: SMPTE 310M (19.4 Mb/s) to 1.5 Gb/s

Connector: 1 BNC per IEC 61169-8 Annex A

Equalization: Automatic to 130m @ 1.5 Gb/s with Belden 1694A or equivalent cable

Return Loss: > 15 dB up to 1.5 Gb/s

3.2. SERIAL VIDEO OUTPUTS

Number of Outputs: 7 Reclocked

Connector: BNC per IEC 61169-8 Annex A

Signal Level: 800mV nominal

DC Offset: 0V ±0.5V

Rise and Fall Time:

SD Video 740ps nominal

HD Video 200ps nominal

Overshoot: < 10% of amplitude

Return Loss: > 15 dB up to 1.5 Gb/s

Wide Band Jitter: < 0.2 UI

3.3. ELECTRICAL

Voltage: + 12VDC

Power: 5 Watts

Safety: CSA Listed to CSA C22.2 No. 60065-03, UL 60065-03

IEC 60065-(2001-12) 7th Edition

Complies with CE Low voltage Directive 93/68/EEC

EMI/RFI: Complies with FCC regulations for class A devices.

Complies with EU EMC directive 89/336/EEC

3.4. PHYSICAL

Number of slots: 1

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Page-4 Revision 1.1

4. STATUS LEDS

The 7700DA7-HD has eight LED Status indicators on the front card edge to show operational status of the

card at a glance. Figure 5-1 shows the location of the LEDs.

Two large LEDs on the front of the board indicate the general health of the module.

LOCAL FAULT: This Red LED indicates poor module health and will be On during the absence of a

valid input signal or if a local input power fault exists (i.e.: a blown fuse). The LOCAL

FAULT indication can also be reported to the frame through the FRAME STATUS

jumper.

MODULE OK: This Green LED indicates good module health. It will be On when a valid input

signal is present, and board power is good.

There are six small LEDs that indicate the status of the equalizer and reclocker.

LOCK: This Green LED will be On when there is a valid signal present at the module input.

RECLOCKER RATE:There are 5 LEDs that indicate the rate (143, 177, 270, 360 or 540 Mb/s) that the

reclocker is currently using when the Rate jumper is set to the 259M/344M position.

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Revision 1.1 Page-5

5. JUMPERS AND USER ADJUSTMENTS

MODULE STATUS

(A)7700DA7-HDSD

SFF POWER

+12V

GND

143M

270M

540M

177M

360M

1.5G

J15

J16

J24

FRAME STATUS

RUN / UPGRADE

ON / OFF

J19

CONTROL

LOCAL/REMOTE

SERIAL

ASI

177

SMPTE

310M

J18

Figure 5-1: LED and Jumper Locations

5.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED

BY THE GLOBAL FRAME STATUS

The FRAME STATUS jumper J15, located at the front of the module determines whether local faults (as

shown by the Local Fault indicator) will be connected to the 7700FR frame's global status bus.

FRAME STATUS: To monitor faults on this module with the frame status indicators (on the power

supply’s FRAME STATUS LED's and on the Frame's Fault Tally output) install this

jumper in the On position.

When this jumper is installed in the Off position local faults on this module will not

be monitored.

5.2. SELECTING WHETHER MODULE WILL BE CONTROLLED FROM THE

LOCAL CONTROLS OR THROUGH THE V

ISTA

LINK

INTERFACE

The CONTROL jumper J19 selects whether the module will be controlled from the local jumpers or

through the VistaLINK

interface.

CONTROL: When this jumper is installed in the LOCAL position, the card functions are

controlled through the local jumpers.

When this jumper is installed in the REMOTE position, the card functions are

controlled through the VistaLINK

interface.

7700 MultiFrame Manual

7700DA7-HD HD Serial Digital Re-Clocking Distribution Amplifier

Page-6 Revision 1.1

5.3. SELECTING THE RECLOCKING RATE

The RATE jumper J18, located at the front of the module near the card ejector, determines whether the

module will operate as a reclocking distribution amplifier with SMPTE 292M, SMPTE 259M or 344M (143

to 540 Mb/s) or DVB-ASI video signals or with SMPTE 310M (19.4 Mb/s) signals.

RATE SELECT: To set the module to operate with SMPTE 292M, SMPTE 259M, SMPTE 344M or

DVB-ASI signals install the jumper in the SMPTE position.

To set module to operate with SMPTE 310M signals install the jumper in the 310M

position.

The SUPPORT jumper J7, located at the front of the module near the card ejector, determines whether

the module will operate as a reclocking distribution amplifier with SMPTE 292M or SMPTE 259M or 344M

(143 to 540 Mb/s) or DVB-ASI video signals.

SUPPORT: To set the module to operate with SMPTE 292M, SMPTE 259M or SMPTE 344M

signals install the jumper in the 177 position.

To set module to operate with DVB-ASI signals install the jumper in the DVB

position.

5.4. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES

UPGRADE: The UPGRADE jumper J16, located at the front of the module near the card ejector,

is used when firmware upgrades are being done to the module. For normal

operation it should be installed in the RUN position. See the Upgrading Firmware

section in the front of the binder for more information.

To upgrade the firmware in the module unit pull it out of the frame. Move Jumper

J16 into the UPGRADE position. Install the Upgrade cable provided (located in the

vinyl pouch in the front of this manual) onto header J24. Re-install the module into

the frame. Run the upgrade as described in the Upgrading Firmware section in the

front of the binder. Once the upgrade is completed, remove the module from the

frame, move J16 to the RUN position, remove the upgrade cable and re-install the

module. The module is now ready for normal operation.

Tabla de contenidos

Otros manuales de Amplificador de evertz

evertz

evertz 7700 Series Manual de usuario

evertz

evertz exponent 500ADA-AUD Manual de usuario

evertz

evertz exponent 500DA-L Manual de usuario

evertz

evertz 7700 Series Manual de usuario

evertz

evertz exponent 500ADA Manual de usuario

evertz

evertz exponent 500DA2Q-HD Manual de usuario

evertz

evertz exponent 520DARS-W Manual de usuario

evertz

evertz exponent 500ADA-EQ Manual de usuario

evertz

evertz 7700 Series Manual de usuario

evertz

evertz 7700 Series Manual de usuario

evertz

evertz 7700 Series Manual de usuario

evertz

evertz exponent 500DA-AESU-L Manual de usuario

evertz

evertz 500DA2Q-3G Manual de usuario

evertz

evertz 7700DA6-L Manual de usuario

evertz

evertz 7700DA-HD Manual de usuario

evertz

evertz 500DA-AESB Manual de usuario

evertz

evertz 7700 Series Manual de usuario

evertz

evertz 7700ADA7-EQ MultiFrame Manual de usuario

evertz

evertz 7800DA8-12G Manual de usuario

evertz

evertz 7710DCDA-HD Manual de usuario

evertz

evertz 7815VPDA Series Manual de usuario

evertz

evertz exponent 500ADA-EQ-L Manual de usuario

evertz

evertz 7700 MultiFrame Manual de usuario

evertz

evertz 7800DA7-MADI Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario

evertz 7700DA7-HD Manual de usuario

Manuales populares de Amplificador de otras marcas