Event Lighting ORBIT2 Manual de usuario

www.event-lighting.com.au

ORBIT2

3-in-1 Effect Light

USER MANUAL

For safety, please read this user manual carefully before initial use.

Event Lighting reserves the right to revise the manual at any time. Information and specifications

within this manual are subject to change without notice. Event Lighting assumes no liability or

responsibility for any errors or omissions. Please consult Event Lighting for any clarification or

information regarding this item.

Version: 10 (6 May 2020)

www.event-lighting.com.au

Safety Instructions

Warning

• Do not open this device, there are no user-serviceable parts inside. The laser power

inside the housing can start fires or burn skin and will cause eye injury.

• Do not look at the light source when the device is on.

• This unit's housing may be hot during and after operation.

• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from

adjacent surfaces.

• Do not leave any flammable material within 50 cm of this unit while operating or

connected to power.

• Do not operate this device outdoors or in any location where dust, excessive heat, water,

or humidity may affect it.

• Do not operate this device if the housing, lenses, or cables appear damaged.

• Do not connect this device to a dimmer or rheostat.

• ONLY connect this device to a grounded and protected circuit.

• ONLY use the hanging bracket to carry this device.

• In case of a serious operating problem, stop using immediately.

• The maximum ambient temperature is 104° F (40° C). Do not operate this device at

higher temperatures.

• Do not leave the product running unattended. Use the key to lock the laser to avoid

unauthorised use.

• Use aperture cover when the laser is not in use.

Laser Warning

Laser light can cause instant eye injury if the product is not set up and used correctly.

Avoid direct eye contact with the laser light. Never intentionally expose your eyes or others to

direct laser light. This laser product can potentially cause instant eye damage or blindness if

laser light directly strikes the eyes. The heat from a laser cannot be felt, but it can still injure or

blind people. This can occur even with very small amounts of exposure at a long distance.

This product contains a Class 3B Laser. It is critical to prevent the possibility of ANY direct eye

exposure.

• Do not operate the laser without reading and understanding the safety information

contained in this manual.

• Do not assume exposure to an individual laser beam is safe.

• Do not assume a moving laser light is safe. Eye injury can occur instantly.

www.event-lighting.com.au

• ORBIT2 must be installed at least 3 metres above ground level and at least 3 metres

horizontally from any person. See the Product Installation section for details.

• Do not point the laser at any person or animal.

• Do not point the laser towards any area where people could be exposed to it.

• Do not point the laser towards any reflective surfaces, such as windows, mirrors and

metals. Laser reflections can also cause injury.

• Do not point the laser towards any area where you or the operator do not know where it

is being directed.

• Do not point the laser into the sky or towards any aircraft.

• The legal requirements for operating laser products vary between jurisdictions. It is the

user’s responsibility to meet the legal requirements in the location/country of use.

Additional laser warning stickers (pictured above) are included with this user manual. Please

attach these to the power supply.

Power Input

This device has an auto-switching power supply work with input voltage range of 100~240 VAC,

50/60 Hz.

Product Installation

• This device can be mounted in many orientations provided each individual device is

secured by the use of correct mounting bracket.

• This device should be directed above the heads of people. Do not direct this device

towards the line of sight of anyone.

o Refer to the diagram below.

• A minimum of 3 meters vertical separation is required between the floor and the laser

device.

• A minimum of 3 metres horizontal separation is required between the laser light and any

person or public space.

• Use a safety chain when mounting this device overhead.

www.event-lighting.com.au

Laser Interlock

The use of the laser is controlled by an interlock and key located on the back of the unit. In order

for the laser to operate, the interlock must be inserted, and the key switched to the unlocked

position.

• If these conditions are not met, only the LEDs will be operational.

Overview

Dimensions

www.event-lighting.com.au

Menu Operation

1. Menu – Move up a level.

2. Up – Move selection up one item.

3. Down – Move selection down one item.

4. Enter – Select / Move down a level.

5. DMX Signal LED indicator. LED will flash when

DMX connected.

6. Master/Slave mode indicator. LED will flash when

in Slave mode.

Display

Function

Description

Addr

DMX Address

Change DMX Address (A001-

A512).

ChNd

DMX Channels

Change DMX Channel Mode

(2Ch / 11Ch).

SLNd

Master/Slave Mode

Change between Master

(NASt) and Slave (SL1/SL2)

mode.

In Slave Mode 1 (SL1), slave

fixtures will follow the Master

fixture when in Sound Active

Mode.

In Slave Mode 2 (SL2), each

slave fixture will use its own

microphone and behave

independently when in Sound

Active Mode.

When not in Sound Active

Mode, SL1 and SL2 function

identically.

Soun

Sound Mode and Sound

Sensitivity

Change between Sound

Active Modes (So0-So8) and

Sound Sensitivity (Se00-

Se99)

Auto

Auto-run Mode

Change between Auto-run

Modes (Aut0-Aut8) and Auto-

run Speed (SP1-SP9)

Led

Display backlight

Turn the display backlight on

or off.

diSP

Display normal/inverted.

Switch between normal or

inverted display mode.

Ver

Software Version

Display the current software

version.

www.event-lighting.com.au

IR Remote

Button

Description

Black Out

Turn on/off

Auto

Autoplay

Sound

Sound Active mode

Strobe

Strobe mode

Fade/ Jump

No Function

Sensitivity

Adjust sound sensitivity

R/G/B/W/A/UV/W

No Function

Increase parameter (strobe

speed, sound sensitivity, auto

speed)

Decrease parameter (strobe

speed, sound sensitivity, auto

speed)

0-8

Switch between functions in

Auto Mode and Sound Active

Mode

No Function

DMX Chart

The device is controlled by universal DMX 512 protocol, DMX address is the start channel used

to receive instructions from the external controller. For independent control, each fixture must be

assigned its unique address control channels. For example, this device has three channel

modes: 2/11, if we set the mode to standard 2 channels mode, and there are several models that

need to be independently controlled, we just simply address first fixture at 1, and second fixture

at 3, third one at 5, etc.

• If the devices have the same address, they will behave synchronically.

• Display is flashing when no DMX signal is received.

www.event-lighting.com.au

2 Channel Mode

Channel

Value

Function

5-20

Auto 0 (combined effect)

21-35

Auto 1 (Derby effect 1)

36-50

Auto 2 (Derby effect 2)

51-65

Auto 3 (Laser + strobe)

66-80

Auto 4 (Derby + strobe)

81-95

Auto 5 (Laser + Derby 1)

96-110

Auto 6 (Laser + Derby 2)

111-125

Auto 7 (Laser effect)

126-130

Auto 8 (Strobe effect)

131-144

Sound 0 (Combined effect)

145-159

Sound 1 (Derby effect 1)

160-174

Sound 2 (Derby effect 2)

175-189

Sound 3 (Laser + strobe)

190-204

Sound 4 (Derby + strobe)

205-219

Sound 5 (Laser + Derby 1)

220-234

Sound 6 (Laser + Derby 2)

235-249

Sound 7 (Laser effect)

250-255

Sound 8 (Strobe effect)

0-255

Run speed and sound sensitivity adjust

www.event-lighting.com.au

11 Channel Mode

Channel

Value

Description

Function

0-13

Derby 1

None

14-27

Red

28-41

Green

42-55

Blue

56-69

White

70-83

Red + Green

84-97

Red + Blue

98-111

Red + White

112-125

Green + Blue

126-139

Green + White

140-153

Blue + White

154-167

Red + Green + Blue

168-181

Red + Green + White

182-195

Red + Blue + White

196-209

Green + Blue + White

210-223

Red + Green + Blue + White

224-237

Jump change with Derby effect 1

238-255

Jump change with Derby effect 2

0-250

Derby 1 Strobe Effect

Speed from slow to fast

251-255

Sound strobe

0-13

Derby 2

None

14-27

Red

28-41

Green

42-55

Blue

56-69

White

70-83

Red + Green

84-97

Red + Blue

98-111

Red + White

112-125

Green + Blue

126-139

Green + White

140-153

Blue + White

154-167

Red + Green + Blue

168-181

Red + Green + White

182-195

Red + Blue + White

196-209

Green + Blue + White

210-223

Red + Green + Blue + White

224-237

Jump change with Derby effect 1

238-255

Jump change with Derby effect 2

0-250

Derby 2 Strobe Effect

Speed from slow to fast

251-255

Sound strobe

0-7

Laser effect

None

8-47

Red

48-87

Green

88-127

Red + Green

128-167

Red + Green Strobe

168-207

Green + Red strobe

208-255

Alternate strobe

www.event-lighting.com.au

0-250

Laser Strobe effect

Speed from slow to fast

251-255

Sound activated

0-7

Laser rotation

No rotation

8-87

Backwards rotation, slow to fast

88-167

Forwards rotation, fast to slow

168-255

Random rotation

0-7

Strobe mode

(centre, can add

effects on top)

No function

8-36

No Strobe

37-66

Strobe effect 1

67-96

Strobe effect 2

97-126

Strobe effect 3

127-156

Strobe effect 4

157-186

Strobe effect 5

187-216

Strobe effect 6

217-246

Strobe effect 7

246-255

Strobe effect 8

0-255

Strobe effect speed

Ch. 8 effect speed, slow to fast

0-7

Strobe effect

No Strobe

8-240

Strobe speed, slow to fast

241-255

Sound activated

0-9

Derby Rotation

None

10-255

Motor rotation, slow to fast

Technical Specifications

• Power supply: 100-240V AC, 50/60Hz

• Power consumption: 45W

• Light Source:

o Derby: 2pcs 12W RGBW LEDs

o Strobe: 24pcs 0.2w SMD White LEDs

o Laser: 532nm/30mW (Green) laser diode, 650nm/100mW (red) laser diode

• Lifetime: 50,000 hours

• Control Panel: 4 digital LED display figures

• Control Mode: Sound activated, Auto, Master/Slave, DMX512, IR Remote

• DMX Channels: 2 / 11

• Dimensions: 320x320x320 (package)

• Weight: 3.35kg

Warranty

Please refer to your local dealer or contact Event Lighting Pty Ltd.

Tabla de contenidos

Otros manuales de Equipo de DJ de Event Lighting

Event Lighting

Event Lighting PIXBAR6x12 Manual de usuario

Event Lighting

Event Lighting PAR12x8A Manual de usuario

Event Lighting

Event Lighting BLINDER Series Manual de usuario

Event Lighting

Event Lighting LM6X15 Manual de usuario

Event Lighting

Event Lighting PS200LECW Manual de usuario

Event Lighting

Event Lighting PARRGBW12x8 Manual de usuario

Event Lighting

Event Lighting M1S75W Manual de usuario

Event Lighting

Event Lighting PAR12X12L Manual de usuario

Event Lighting

Event Lighting LM60S Manual de usuario

Event Lighting

Event Lighting STROBEXRGB Manual de usuario

Event Lighting

Event Lighting F100WWMZ Manual de usuario

Event Lighting

Event Lighting M1S80W Manual de usuario

Event Lighting

Event Lighting STORM Manual de usuario

Event Lighting

Event Lighting PARP12x8 Manual de usuario

Event Lighting

Event Lighting CO2RGB Manual de usuario

Event Lighting

Event Lighting LM180 Manual de usuario

Event Lighting

Event Lighting PARRGBW12x8 Manual de usuario

Event Lighting

Event Lighting M19W15RGBW Manual de usuario

Event Lighting

Event Lighting KONTROL36 Manual de usuario

Event Lighting

Event Lighting PS300IICW Manual de usuario

Event Lighting

Event Lighting BM1S50W Manual de usuario

Event Lighting

Event Lighting SToRM Manual de usuario

Event Lighting

Event Lighting PRO PAR PAR12X8L Manual de usuario

Event Lighting

Event Lighting PANBEAM4x4x10 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario