Euphonix EuCon Manual de usuario
EuCon Application Setup Guide
MUSIC | AUDIO POST | VIDEO | FILM
Document Revision: H
professional control surface professional control surface
professional control surfaces
Artist Series
EuCon APPLICATION SETUP GUIDE
ii
MC Control, MC Mix, Studio Monitor Express, Studio Monitor Pro, EuControl, EuCon and
EuCon Powered are trademarks of Euphonix Inc. All other product names are trademarks
of their respective manufacturers.
professional control surfaces
Artist Series
EuCon APPLICATION SETUP GUIDETABLE OF CONTENTS
iii
Table of Contents
Section 1: Introduction......................................................................................... 5
Section 2: Logic Pro.............................................................................................. 5
Section 3: Nuendo ................................................................................................ 6
3.1 EuCon Device Setup ..................................................................... 7
3.1.1 EuConized channel types ................................................. 8
3.1.2 Global Settings................................................................ 8
Section 4: Cubase ............................................................................................... 10
4.1 EuCon Device Setup ................................................................... 11
4.1.1 EuConized channel types ............................................... 12
4.1.2 Global Settings.............................................................. 12
Section 5: Digital Performer.............................................................................. 14
Section 6: Mackie Control.................................................................................. 16
6.1 Setting Up EuCon for Mackie Control .......................................... 16
6.2 Final Cut Pro and Soundtrack Pro................................................ 19
6.3 Ableton Live ............................................................................... 21
6.4 Reason....................................................................................... 23
Section 7: Pro Tools (HUI) ................................................................................. 25
7.1 Setting up EuCon to Control Pro Tools ........................................ 25
7.2 Setting up Pro Tools to Control the Artist Devices ....................... 27
professional control surfaces
Artist Series
EuCon APPLICATION SETUP GUIDE
INTRODUCTION
5
Section 1: Introduction
The EuCon Application Setup Guide helps you setup EuControl to work with your
specific application. EuControl must be installed before proceeding to your ap-
plication’s section in this Guide. See the Installation section in the Quickstart or
User Guides to install EuControl if you have not already done so.
Section 2: Logic Pro
Logic Pro 8 works with your Artist control surface with very little additional setup.
Make sure the EuControl software is running. Launch Logic Pro and click in a
Logic window so it is the front-most application. Your surface now controls Logic
Pro.
To make sure your Artist control surface works correctly with Logic Pro:
1. In Logic Pro, choose Logic Pro -> Preferences -> Control Surfaces -> Setup...
The Logic Control Surface Setup window appears.
Figure 2-1 Logic Control Surface Setup window
2. In Control Surface Group 1 on the left side of the window, locate Channel
Strip View Mode (fourth parameter from top).
3. Set this parameter to Arrange, not one of the other settings.
Use Software Update so your Mac stays updated the latest version of Logic Pro.
professional control surfaces
Artist Series
EuCon APPLICATION SETUP GUIDE
NUENDO
6
Section 3: Nuendo
Nuendo 4 is a powerful DAW that can handle as many tracks and effects as your
workstation’s CPU can support. It offers multitrack recording, editing, and
monitoring. Steinberg’s EuCon adapter enables fully integrated control of all of
Nuendo’s functions from the Artist control surfaces.
NOTE: The adapter works with Nuendo version 4.1.2 and later.
To enable Nuendo to work with the Artist, you must obtain an activation code:
1. Create a user account in the MySteinberg area of Steinberg’s web site.
If you already have a MySteinberg account and have already registered your
version of Nuendo 4, continue with Step 4.
2. Check your email and activate your user account by clicking the link in the
confirmation email.
3. Log into your MySteinberg account, click on Product Registration, choose
Register Product and select Product with Steinberg Key or Soft-eLicenser.
4. Log into your MySteinberg account if you have not already. Click on Activa-
tion & Reactivation, choose Euphonix Artist Series EuCon Adapter and select
Permanent Activation. Enter your Artist device’s serial number.
You will receive an email containing the activation code.
5. Launch the License Control Center (LCC) Software from the Applications
folder, choose Wizards->License Download, enter your activation code and
follow the instructions.
For Nuendo to communicate with the Artist devices, Nuendo’s EuCon device
must be added in the Device Setup dialog:
1. Open Nuendo.
2. Choose Devices->Device Setup.
The Device Setup dialog opens.
3. Click the +button (add) on the top-left.
A drop-down list of devices appears with EuCon near the top of the list.
professional control surfaces
Artist Series
EuCon APPLICATION SETUP GUIDE
NUENDO
7
4. Select EuCon from the drop-down list.
The EuCon device is added, the control surface immediately updates, the
faders and knobs display track functions, and the EuCon Device Setup dialog
appears (Figure 3-1).
3.1 EuCon Device Setup
This section discusses the EuCon Device Setup dialog which allows editing track
assignment and transport control parameters. If the EuCon Device setup dialog
is not open: From Nuendo choose Devices->Device Setup, then select EuCon
from the Remote Devices folder in the Devices section.
Figure 3-1 EuCon Device Setup
professional control surfaces
Artist Series
EuCon APPLICATION SETUP GUIDE
NUENDO
8
3.1.1 EuConized channel types
The EuConized channel types section contains checkboxes that determine
which channel types appear on your control surface. If a certain channel is
available in Nuendo and the corresponding checkbox is selected, that channel
can be selected to appear on the surface. This channel is called EuConized.
All channels except Input channels are EuConized by default and can appear on
the surface. This is useful to eliminate tracks from the surface, reduce memory
usage, and reduce the time needed to build the EuCon mixer model when con-
necting, adding, or removing tracks from the Nuendo project.
To enable/disable EuConized tracks, select the checkbox next to each type.
Tracks without a checkmark do not appear on the surface. This setting applies
only to the open project.
3.1.2 Global Settings
The Global Settings section has two parameters: Tape machine style transport
and Number of knobsets to cache.
Tape machine style transport
Two Nuendo transport control modes are available for the control surface.
Toggle the modes from the Tape machine style transport option.
These transport modes affect the operation of the Stop, Fast Forward and Rewind
buttons in the following manner:
Tape machine style transport checked
Stop: The control surface STOP button halts the transport and keeps the play
head at the current position (even multiple presses), independent from Nu-
endo’s preferences.
Fast Forward/Rewind: The FF/RW buttons always latch independent of the
control surface latch time preference. Repeatedly pressing the same FF/RW
button has no effect. The current action can be stopped by pressing the op-
posite wind button, STOP, or PLAY. The FF/RW also stops if it reaches the be-
ginning or end of the project.
professional control surfaces
Artist Series
EuCon APPLICATION SETUP GUIDE
NUENDO
9
Tape machine style transport not checked
Stop: The control surface STOP button copies the Nuendo stop button.
Fast Forward/Rewind: The FF/RW buttons function as EuCon Momentary/
Latch-Switches. If the button is pressed and released quickly, the switches
do NOT latch but behave momentarily, resembling the way these buttons
work in the Nuendo GUI. If the Artist device’s FF/RW buttons are held down
longer than the latch time set in the Preferences-Setup page, they latch.
Number of knobsets to cache
Nuendo creates knobsets for EQ, Dynamic, Inserts, Aux sends and other functions.
A certain number of these knobsets are kept, or cached, in RAM. For large
projects on a large control surface, increasing the number of knobsets in the cache
can access them faster but uses more RAM. It is rare to change this value.
professional control surfaces
Artist Series
EuCon APPLICATION SETUP GUIDE
CUBASE
10
Section 4: Cubase
NOTE: Cubase version 4.1.2 and higher is required. Download the latest version of Cu-
base from Steinberg's web site.
To enable Cubase to work with your Artist device, you must obtain an activation
code:
1. Create a user account in the MySteinberg area of Steinberg’s web site.
If you already have a MySteinberg account and have already registered your
version of Cubase 4, continue with Step 4.
2. Check your email and activate your user account by clicking the link in the
confirmation email.
3. Log into your MySteinberg account, click on Product Registration, choose
Register Product and select Product with Steinberg Key or Soft-eLicenser.
4. Log into your MySteinberg account if you have not already. Click on Activa-
tion & Reactivation, choose Euphonix Artist Series EuCon Adapter and select
Permanent Activation. Enter your Artist device’s serial number.
You will receive an email containing the activation code.
5. Launch the License Control Center (LCC) Software from the Applications
folder, choose Wizards->License Download, enter your activation code and
follow the instructions.
For Cubase to communicate with the Artist devices, Cubase’s EuCon device must
be added in the Device Setup dialog:
1. Open Cubase but do not open a project.
If Cubase automatically opens a project, close it.
2. Choose Devices->Device Setup.
The Device Setup dialog opens.
3. Click the +button (add) on the top-left.
A drop-down list of devices appears with EuCon near the top of the list.
Otros manuales para EuCon
1
Tabla de contenidos
Otros manuales de Software de Euphonix
Manuales populares de Software de otras marcas
PS Audio
PS Audio PowerPlay Manual del propietario
Brady
Brady LOCKOUT PRO 3.0 Manual de servicio
Avaya
Avaya Interaction Center Manual de usuario
Texas Instruments
Texas Instruments TI-83 Plus Silver Edition Manual
Novell
Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario
Oracle
Oracle Application 9i Manual de usuario
Acer
Acer RDM Manual de usuario
Canon
Canon Vixia HF21 Manual de usuario
Canon
Canon ZR950 Manual de usuario
Samsung
Samsung Auto Backup Manual de usuario
Polycom
Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento
Brocade Communications Systems
Brocade Communications Systems Brocade 8/12c Manual de usuario