EtherWAN EL8000 Manual de usuario

User’s Guide

EL8000 Hardened Media Converter

Dissemination or reproduction of this document, or its contents, is not authorized except where expressly

trademark registration.

Disclaimer of Liability

The information contained in this document is subject to change without notice. EtherWAN is not liable for any

errors or omissions contained herein or for resulting damage in connection with the information provided in this

manual.

Warranty

For details on the EtherWAN warranty replacement policy, please visit our web site at:

https://kb.etherwan.com/index.php?CategoryID=13

Products Supported by this Manual:

EL8000

iii

EL8000 Hardened Media Converter

Preface

Audience

This guide is designed for the person who installs, configures, deploys, and maintains the Ethernet

network. This document assumes the reader has moderate hardware, computer, and Internet skills.

Document Revision Level

This section provides a history of the revision changes to this document.

Revision

Document Version

Date

Description

Version 1

1/3/2018

03/14/2018

Safety and Warnings

This guide uses the following symbols to draw your attention to certain information.

Symbol

Meaning

Description

Note

Notes emphasize or supplement important points of the main text.

Tip

Tips provide helpful information, guidelines, or suggestions for performing

tasks more effectively.

Warning

Warnings indicate that failure to take a specified action could result in

damage to the device, or could result in serious bodily injury.

Electric Shock

Hazard

This symbol warns users of electric shock hazard. Failure to take

appropriate precautions such as not opening or touching hazardous

areas of the equipment could result in injury or death.

EL8000 Hardened Media Converter

Contents

Preface..................................................................................................................... iii

Safety and Warnings.................................................................................................iii

Contents.................................................................................................................. iv

Introduction.............................................................................................................. 5

Unpacking.................................................................................................................6

Select Installation Location........................................................................................6

Connect Power..........................................................................................................7

LED Indicators...........................................................................................................8

DIP Switches.............................................................................................................9

Link Fault Pass Through (LFPT)..........................................................................9

Relay Output Alarm.................................................................................................10

Specifications..........................................................................................................11

Manufacturer’s Information......................................................................................12

Introduction

EL8000 Hardened Media Converter

1000Base-TX to 1000Base-SX / LX / BX

1000Base-TX to 1000 SFP

The EL8000 Series provides media conversion between 1000BASE-TX and 1000BASE -

SX/LX/BX/SFP Fiber. Built specifically for mission critical applications in harsh environments, the

EL8000’s hardened design features high shock & vibration resistance, electrical noise immunity, wide

operating temperature range from -40 to 75°C, and aluminum housing. With two power inputs, link

down alarming, Link-Fault-Pass-Through and a wide range of fiber connectivity options, the EL8000 is

the ideal media converter for environments where connectivity is crucial.

EL8000 Hardened Media Converter

Unpacking

Open the carton and unpack the items. Your package should include an EL8000 media converter and

this Quick Install Guide. If items are missing or damaged, notify your EtherWAN representative.

Select Installation Location

Installation is DIN rail-mount, or wall mount (in an enclosure or industrial panel). Ensure that the power

source is within 6 feet (1.8 meters), and check that there is adequate airflow.

Place the media converter on the DIN rail from above using the slot. Push the front of the media

converter toward the mounting surface until it audibly snaps into place.

Startup: Connect the supply voltage to start up the media converter via the terminal block.

Dismantling: Pull out the lower edge and then remove the media converter from the DIN rail.

EL8000 Hardened Media Converter

Connect Power

The media converter is equipped with an eight-contact terminal block. The terminal block provides dual

DC power inputs, and a relay output contact. Redundant power supply is supported, but onlyone power

input is required for operation. Note that the media converter does not have a power switch; it is turned

on/off by connecting/disconnecting power.

Input voltage is 12 to 48VDC.

The power dissipation under full load is as follows:

12VDC/0.4A

48VDC/0.11A

Note: Use qualified power supply by SELV or double insulation of UL 60950 or UL 61010-1 or UL

61010-2-201 standards.

Insert the DC input wires into the corresponding terminals, and tighten the clamp screws to hold them in

place. Make sure that the plastic terminal block connector prongs are plugged firmly into the terminal

block receptacles.

Power wiring information:

Use cable type - AWG (American Wire Gauge) 18-24 and the corresponding pin type cable terminals.

Use torque value 1.7 lb-in, do not use excessive force when fixing wiring.

Label clean up:

Indoor use and pollution degree II, it must be wiped with a dry cloth for clean up the labelling.

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the

equipment may be impaired.

Environment:

The media converter shall be mounted in an industrial control panel and ambient temperature is not

exceed 75 degree Celsius.

Altitude up to 2000 meters.

Humidity range (Operational): 5% to 95%, non-condensation.

The product is open type.

Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes of the

equipment.

EL8000 Hardened Media Converter

LED Indicators

LED

State

Indication

Fault

Steady

Power redundancy or port malfunction

Off

Power redundancy/ports functioning

normally

PW1

Steady

Power1 on

Off

Power1 off

PW2

Steady

Power2 on

Off

Power2 off

LNK/ACT

Steady

Connection established

Flashing

Transmitting or receiving data

Off

No connection established

LFPT

Steady

LFPT function enabled

Off

LFPT function disabled

EL8000 Hardened Media Converter

DIP Switches

Port, power and LFPT settings are made very simple by means of DIP (Dual Inline Package) switches

on the bottom panel of the hardened media converter.

No.

DOWN (Default)

Enable LFPT*

Disable LFPT*

Enable link down alarm for

copper port

Disable link down alarm for

copper port

Enable link down alarm for fiber

port

Disable link downalarm for

fiber port

Enable Auto-negotiation

Enable Force mode

Reserved

* LFPT=Link Fault Pass Through

If Force mode is enabled, the media converter must be restarted in order for the new setting to

take effect.

Link Fault Pass Through (LFPT)

LFPT (Link Fault Pass Through) is a feature that will pass a link fault through the device at each

segment. If either of the copper TX links fails, the media converter will pass the fail state on throughout

the link, taking down the middle fiber as well as the copper link on the opposite end. This prevents the

connected switches from sending packets that would end up lost. LFTP is designed for use with media

converters arranged in pairs, and both devices must support LFPT.

EL8000 Hardened Media Converter

Relay Output Alarm

The media converter is equipped with relay output contacts on the terminal block for signaling of a

power or port failure. The relay output can be connected to an alarm signaling device. Current is 0.6A

@ 30VDC.

Relay contact

PW1

PW2

Point

1 - 2

Point

2 - 3

Alarm

Off

Closed

Open

Alarm

Off

Closed

Open

Alarm

Off

Closed

Open

Non-Alarm

Open

Closed

Tabla de contenidos

Otros manuales de Convertidor de medios de EtherWAN

EtherWAN

EtherWAN EMC1600 Series Manual de usuario

EtherWAN

EtherWAN EX42011 Manual de usuario

EtherWAN

EtherWAN EL100 Manual de usuario

EtherWAN

EtherWAN EMC1200R Manual de usuario

EtherWAN

EtherWAN EL50 Series Manual de usuario

EtherWAN

EtherWAN EL2326 Series Manual de usuario

EtherWAN

EtherWAN EL2242 Series Manual de usuario

EtherWAN

EtherWAN EL1032T Series Manual de usuario

EtherWAN

EtherWAN EL2242 Series Manual de usuario

EtherWAN

EtherWAN EM120 Manual de usuario

EtherWAN

EtherWAN EM1100 Manual de usuario

EtherWAN

EtherWAN EL1142 Series Manual de usuario

EtherWAN

EtherWAN EL900 Series Manual de usuario

EtherWAN

EtherWAN EL900 Series Manual de usuario

EtherWAN

EtherWAN EL2321 Manual de usuario

EtherWAN

EtherWAN EL2211 Manual de usuario

EtherWAN

EtherWAN EL100 Manual de usuario

EtherWAN

EtherWAN EMC400 Manual de usuario

EtherWAN

EtherWAN EL100 Manual de usuario

EtherWAN

EtherWAN EMC1600 Series Manual de usuario

EtherWAN

EtherWAN EMC1200R Manual de usuario

EtherWAN

EtherWAN EL1032T Series Manual de usuario

EtherWAN

EtherWAN EL2321 Manual de usuario

EtherWAN

EtherWAN EL900 Series Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario