ETEKCITY EHS-18 Manual de usuario
2
Thank you for purchasing the
Digital Hanging Scale by Etekcity.
If you have any questions or concerns, please
reach out to our helpful Customer Support
enjoy your new scale!
BECOME AN ETEKCITIZEN
Get exclusive deals, giveaways, and product
registration. Better products for better living.
Find us at etekcity.com
3
1 x Digital Hanging Scale
2 x 3V CR2032 Batteries (Pre-Installed)
1 x Carrying Pouch
1 x User Manual
Package ContentsTable of Contents
Package Contents
Specications
Safety Information
Function Diagram
LCD Display
Setup
• Battery Installation
Operation
• Weight Measurement
• Unit Conversion
• Data Hold Function
• Tare Function
Care & Maintenance
• Replacing Batteries
Warranty Information
Customer Support
3
4
4
5
6
7
7
8
8
8
9
9
10
10
11
14
4
Safety Information
•Do not exceed the weight capacity of 110 lb
(50 kg). An overload indicator will appear
on the digital display if the limit is exceeded.
• This scale is not intended for commercial or
heavy-duty use. Household use only.
•Do not throw or strike the scale and do not
submerge the scale in water.
Follow all instructions and safety guidelines.
Read all instructions before using.
SAVE THESE
INSTRUCTIONS
Specications
Dimensions 8.3x 3.3 x 1.1inches
(210 x 84 x 29mm)
Weight Capacity 110 lb (50 kg)
Units oz / g / lb / kg
Auto-Off 60 seconds
Power 2 x 3V CR2032 Batteries
Weight of Object Accuracy
< 44 lb (20 kg) +/- 0.4 lb (0.2 kg)
> 44 lb (20 kg) +/- 0.8 lb (0.4 kg)
5
Function Diagram
A. Handle
B. LCD Display
C. ON/OFF Button
D. TARE Button
E. UNIT Button
F. Measuring Tape
G. Hook
H. Battery Compartment
I. Hook Storage
A
B
G
F
H
I
C
D
E
Front Back
6
LCD Display
A. Measured weight is less than
the calibrated tare weight
B. Displayed weight is the
tared weight
C. Last measured weight
D. Weight in grams
E. Weight in ounces
F. Weight in kilograms
G. Weight in pounds
H. Maximum weight capacity
has been exceeded
(remove object from hook
immediately)
I. Battery low
Tare
Hold
H
I
AE
G
D
F
B
C
g
kg
lb
oz
7
Setup
1. Open the battery cover.
2. Remove the insulation strip to activate
the batteries. [Figure 1.1]
3. When replacing the batteries, make
sure to insert them under the proper
polarity.
Battery Installation
Figure 1.1
8
Press UNIT repeatedly to change the unit
of measurement (oz / g / lb / kg).
Unit Conversion
1. Press ON/OFF and the screen will
light up. Wait for “ “ to appear on
the screen. [Figure 2.1]
2. Hang the object you want to measure
on the hook.
3. Lift the scale with the object and hold
still until the weight measurement
stabilizes. The display will show the
weight and “Hold”.
4. To measure another item, remove the
object and repeat steps 2 and 3.
Operation
Weight Measurement Note: To avoid result inaccuracy, keep the scale
upright when measuring. Do not touch or move
the scale during measurement. Always grasp
the scale by the handle.
5. Press ON/OFF to turn the scale off.
The scale will automatically turn off if
the scale is inactive for 60 seconds.
lb
Figure 2.1
9
Once the weight has stabilized and “Hold”
appears on screen, the weight will stay
on the screen for 60 seconds, or until you
measure another object or press TARE.
Turning the data hold function on or off:
1. When the scale is on, press and hold
TARE for 3 seconds.
2. Press UNIT to alternate between
turning data hold function on or off.
Hoon - Data hold function on
HooF - Data hold function off
3. Press TARE to conrm selection.
Data Hold Function
The tare function allows users to weigh an
object inside a container by subtracting
the weight of the container from the total
weight.
1. Hang the container on the weighing
scale hook and allow the weight to
stabilize and lock (the word “Hold” will
appear).
2. Hold the scale stable and press TARE
to tare the current weight. The display
will show “ “.
3. Place the object you want to weigh
inside the container and the scale
will calculate the weight of the object
without the weight of the container.
Tare Function
10
Care & Maintenance
• Do not use chemical detergents to
clean the scale. Use a soft, damp cloth
if needed.
• If not in use for a long period of time,
remove the batteries and store the
scale in a cool, dry environment to
avoid circuit damage.
1. Locate the battery compartment on
the back of the scale and remove the
battery compartment cover.
2. Ensure the +side of the battery is
facing up and insert the batteries into
the battery slots. [Figure 3.1]
3. Replace cover.
Replacing Batteries
Figure 3.1
Otros manuales para EHS-18
2
Tabla de contenidos
Otros manuales de Escala de ETEKCITY
ETEKCITY
ETEKCITY EB4887S Series Manual de usuario
ETEKCITY
ETEKCITY EKS-C193 Manual de usuario
ETEKCITY
ETEKCITY ESF38 Manual de usuario
ETEKCITY
ETEKCITY EB4074C Manual de usuario
ETEKCITY
ETEKCITY EK7090 Manual de usuario
ETEKCITY
ETEKCITY ESF18 Series Manual de usuario
ETEKCITY
ETEKCITY ESN00 Manual de usuario
ETEKCITY
ETEKCITY ESF17 Manual de usuario
ETEKCITY
ETEKCITY EK6020 Manual de usuario
ETEKCITY
ETEKCITY ESF17 Manual de usuario
ETEKCITY
ETEKCITY EK5150 Manual de usuario
ETEKCITY
ETEKCITY EK6015 Manual de usuario
ETEKCITY
ETEKCITY EK8060 Manual de usuario
ETEKCITY
ETEKCITY EK8060 Manual de usuario
ETEKCITY
ETEKCITY ESF-551 Manual de usuario
ETEKCITY
ETEKCITY EB4410B Manual de usuario
ETEKCITY
ETEKCITY EB4074S Manual de usuario
ETEKCITY
ETEKCITY ESN90 Manual de usuario
ETEKCITY
ETEKCITY EL11 Manual de usuario
ETEKCITY
ETEKCITY Luminary EKS-L221-SEU Manual de usuario
