ETC Source 4WRD Manual de usuario

Part Number: 7067M1200-1.0.0 Rev: F

Released: 2016-11

Source 4

WRD

HPL to LED Retrofit

Installation and User Manual

Version 1.0.0

ETC

, Source Four

, Source 4

WRD

™

, and Unison

are either

registered trademarks or trademarks of Electronic Theatre

Controls, Inc. in the United States and other countries.

All other trademarks, both marked and not marked, are the

property of their respective owners.

This product is protected by one or more of the following U.S.

Patents: US 9,261,241 and 9,273,831.

ETC intends this document, whether printed or electronic, to be

provided in its entirety. This product is intended for

professional use only. Read this entire document before using

this product.

Table of Contents

Source 4

WRD

User Manual i

Introduction . . . . . . . . . . . . . . . . . . . . . . . 1

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Sensor dimmer settings . . . . . . . . . . . . . . . . . . 4

Color rendering and quality . . . . . . . . . . . . . . 5

Contacting ETC . . . . . . . . . . . . . . . . . . . . . 6

Retrofit Kit Installation. . . . . . . . . . . . . . . 7

Remove Incandescent Lamp Housing . . . . . . . 7

Install Source 4WRD . . . . . . . . . . . . . . . . . . . . . . 8

Fixture Installation . . . . . . . . . . . . . . . . . . 9

C-clamp and safety cable. . . . . . . . . . . . . . . . . 9

Connect cables . . . . . . . . . . . . . . . . . . . . . . . . 10

DMX pinout . . . . . . . . . . . . . . . . . . . . . . . 11

User Interface . . . . . . . . . . . . . . . . . . . . . 12

Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Focus the fixture . . . . . . . . . . . . . . . . . . . 13

Z-adjustment Knob . . . . . . . . . . . . . . . . . . . . 13

Adjust the yoke position . . . . . . . . . . . . . . . . 13

Shape the beam. . . . . . . . . . . . . . . . . . . . . . . 14

Color Frame . . . . . . . . . . . . . . . . . . . . . . . 14

Pattern Projection . . . . . . . . . . . . . . . . . . 15

ii Source 4

WRD

User Manual

Cleaning and Maintenance. . . . . . . . . . . 15

Cleaning Source 4WRD . . . . . . . . . . . . . . . . . . . 15

Recommended Storage . . . . . . . . . . . . . . . . . 16

Cleaning Lenses . . . . . . . . . . . . . . . . . . . . . . . 16

Cleaning Reflector . . . . . . . . . . . . . . . . . . . . . 17

Cleaning 5° and 10° polymer lenses . . . . . . . 18

User Manual 1

Introduction

Congratulations on your purchase of the ETC Source 4WRD. Replacing your

existing incandescent burner assembly with the Source 4WRD LED retrofit

brings a new tool to your lighting inventory. Source 4WRD expands the options

for existing Source Four fixtures and adds a new white LED fixture to the ETC

family.

The following Source 4WRD options are available as 80CRI and 90 CRI (Gallery)

variants:

•Source 4WRD Retrofit Kit: Used to modify an existing Source Four HPL

incandescent fixture to a white LED fixture.

•Source 4WRD Light Engine: Combines the Source Four incandescent

fixture body with the Source 4WRD white LED Retrofit Kit.

Note:

Source 4wrd Retrofit Kit is not compatible with

Source Four LED, Fresnel, PAR, or jr fixtures.

WARNING:

Source 4wrd is not user serviceable. Field modification of

the Source 4wrd will void your ETC warranty.

Source 4WRD

shown installed

on a Source Four

fixture

2Source 4

WRD

Safety

The Source 4WRD fixture is intended for professional use only. Read the entire

manual before using this equipment.

WARNING:

Note the following safety warnings before use:

• Do not mount the Source 4wrd fixture on or near a

flammable surface.

• Do not use the Source 4wrd below 5°C (41°F).

• Minimum storage temperature is 5°C (41°F). When the

fixture has been stored or transported in cold

temperatures, allow it to warm to room temperature

for a minimum of 1 hour prior to applying power.

Applying power to a cold fixture will cause damage to

the fixture and void ETC warranty.

• Do not use this fixture with a damaged power lead. If

the power lead (cord set) is damaged, it must be

replaced.

• Do not use this fixture if glass lens is deeply scratched

or cracked. Damaged lenses must be replaced.

• To prevent wiring damage, or abrasion, do not expose

wiring to edges of sheet metal or other sharp objects.

• Use the Source 4wrd fixture in dry locations only,

where humidity does not exceed 90 percent (non-

condensing). These fixtures are not intended for

outdoor use.

• Mount and support the fixture only by the primary

suspension holes in the yoke.

• Suspend the fixture from a suitable structure using

only the hardware rated for the weight of the fixture.

• In addition to primary suspension, attach a safety cable

(ETC Model 400SC or other approved safety cable or

device) to the fixture housing. Appropriate

attachment point (hole) is provided in the protruding

tab on the fixture housing.

• Disconnect the unit from power and DMX and allow

the fixture to cool before removing or installing the

shutter barrel or other adapters, and for performing

all cleaning and maintenance.

User Manual 3

Specifications

Physical

• Rugged die-cast aluminum construction

• Advanced thermal management systems for long LED life

• Ambient operating temperature: 5 to 40 °C (41 to 104°F)

• Minimum storage temperature: 5°C (41°F)

• Weight

-S4

WRD retrofit kit only: 3.65 lbs (1.66 kg)

-S4WRD installed on 26° fixture with yoke and C-clamp:14 lbs (6.35 kg)

Electrical

• 114–125VAC 60Hz power input

• 155 watt draw at full (182 watt theoretical max. draw)

• Recommended two (2) Source 4WRD fixtures per dimmed circuit

(D20 module)

• Max of 14 fixtures per non-dimmed circuit (R20 module)

• If using in DMX mode, connect fixture to relay, constant power, or

dimmer with regulation off and parked at full

LEDs

• 4 CREE LED modules

• 30,000 hour estimated L70 rating (life-test in progress, results pending)

Optical

• Compatible with all ETC Source Four lens tubes

Control

• DMX512-A compliant

• DMX in and thru via two RJ45 connectors

• Simple seven segment display, two button user interface

• AC power for line-dimmed operation

Note:

• Maximum recommended ambient operating

temperature: Ta=40°C (104°F)

• Maximum anticipated external surface temperature:

Tmax=65°C (149°F) at Ta=40°C (104°F)

• External Temperature (steady state achieved) at

25°C (77°F) ambient: 32°C (90°F)

Typical Power Consumption

Idle Power / Current DMX Mode: 1.2W/.046A; AC Mode: 0W

Full Intensity Power / Current 155.7W/1.35A

Note:

Connecting both power and data from a SmartBar 1 to a

Source 4wrd may cause flickering.

4Source 4

WRD

Sensor dimmer settings

The Source 4WRD can be controlled from either a DMX source or from an

existing dimmer for level control.

When powering a fixture from a CEM classic, CEM+, or CEM3 for DMX

dimming or AC level setting, change max scale settings to guarantee the

dimmer is out of regulated mode.

The following table applies to all ETC Sensor control modules including CEM,

CEM+, and CEM3.

The SCR Off Time may need to be increased from the default setting. Contact

ETC for assistance in changing the SCR off time, or any other CEM classic,

CEM+, or CEM3 settings.

For the most current information on additional dimmer performance testing

for both ETC and non-ETC dimmers, please reference our website at:

etcconnect.com/Support/Articles/Dimmer-Settings-for-Use-with-Source-

4wrd.aspx.

Note:

Dimmer settings may need to be adjusted for optimal

fixture control.

Note:

In CEM+ Max Scale must be set to 140V to guarantee that

regulation is off.

Parameter Value Parameter Value

Curve Mod Square Preheat Disabled

Threshold 1% DC Prevent OFF

Min Scale 6V Inrush Protect OFF

Max Scale 140V Scale Load 100

Regulation OFF

Note:

With AC dimming (line-dimmed) mode, performance

may vary based on the control settings of the dimmer

used. For this reason, ETC recommends using AC dimming

for level-setting or for architectural quality dimming

situations. ETC recommends testing Source 4wrd on all

existing dimmers you wish to use.

Use DMX mode when high-performance, live, dynamic

dimming is required.

User Manual 5

Color rendering and quality

Source 4WRD fixtures are evaluated for Color Rendering Index (CRI) and Color

Quality Scale (CQS) performance using measured output spectrum. These

numbers may fluctuate slightly from fixture to fixture. This is a normal

characteristic of white LEDs, and this kind of variation is highly unlikely to be

apparent in most applications.

Contacting ETC

If you are having difficulties, your most convenient resources are the

references given in this user manual. To search more widely, try the ETC Web

site at etcconnect.com. If none of these resources is sufficient, contact ETC

Technical Services directly at one of the offices identified below. Emergency

service is available from all ETC offices outside of normal business hours.

When calling for help, please have the following information handy:

• Product model

• Dimmer manufacturer and installation type

• Other components in your system (Unison, other consoles, etc.)

Fixture CRI CQS Color Fidelity Duv

Source 4wrd

(80CRI) at 3000K ≥80 80 80 0.001

Source 4wrd Gallery

(90CRI) at 3000K ≥90 90 90 0.001

Americas United Kingdom

Electronic Theatre Controls Inc. Electronic Theatre Controls Ltd.

Technical Services Department Technical Services Department

3031 Pleasant View Road 26-28 Victoria Industrial Estate

Middleton, WI 53562 Victoria Road,

800-775-4382 (USA, toll-free) London W3 6UU England

+1-608 831-4116 +44 (0)20 8896 1000

[email protected] [email protected]

Asia Germany

Electronic Theatre Controls Asia, Ltd. Electronic Theatre Controls GmbH

Technical Services Department Technical Services Department

Room 1801, 18/F Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square 83607 Holzkirchen, Germany

9 Sheung Yuet Road +49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong [email protected]om

+852 2799 1220

service@etcasia.com

6Source 4

WRD

Retrofit kit installation

Remove incandescent lamp housing

1: Unplug the Source Four

incandescent fixture and

place it on a flat, stable

surface.

2: Loosen the brass thumb

screw located above the

beam adjustment knob.

The lamp housing is now

loose and can be

removed.

WARNING:

RISK OF FIRE OR ELECTRIC SHOCK: LED Retrofit Kit

installation requires knowledge of luminaires electrical

systems. If not qualified, do not attempt installation.

Contact a qualified electrician.

Note:

THE RETROFIT KIT IS ACCEPTABLE AS A COMPONENT OF

A LUMINAIRE WHERE THE SUITABILITY OF THE

COMBINATION SHALL BE DETERMINED BY AUTHORITIES

HAVING JURISDICTION.

Note:

The burner assembly is no longer needed. If you would

like ETC to recycle the burner assembly, contact ETC

Technical Services for more information. See Contacting

ETC on page 5.

LEDs

Up and down

navigation

RJ45 Data in

and through

User interface

Source 4WRD

Retrofit Kit

A #2 Phillips

screwdriver is

needed for kit

installation

Otros manuales para Source 4WRD

Tabla de contenidos

Otros manuales de Equipo de iluminación de ETC

ETC

ETC ColorSource Spot jr v2.0 Manual de usuario

ETC

ETC Sensor IQ Contact Input Control Option Card Manual de usuario

ETC

ETC XDLT Manual de usuario

ETC

ETC Hog 4 Series Manual de usuario

ETC

ETC Source Four LED Series Manual de usuario

ETC

ETC Source Four HID jr Manual de usuario

ETC

ETC Source Four LED Series Manual de usuario

ETC

ETC Source Four CE 405 Manual de usuario

ETC

ETC HIGH END SYSTEMS SolaPix 37 Manual de usuario

ETC

ETC Selador Series Manual de usuario

ETC

ETC Acclaim 100 series Manual de usuario

ETC

ETC Source 4WRD Manual de usuario

ETC

ETC Source Four LED Series Guía de instalación

ETC

ETC fos/4 Fresnel Manual de usuario

ETC

ETC Desire D22 Manual de usuario

ETC

ETC SolarFrame 750 Manual de usuario

ETC

ETC Source Four LED Series Manual de usuario

ETC

ETC ELTS2 Manual de usuario

ETC

ETC ColorSource Spot Manual de usuario

ETC

ETC microVision FX Manual de usuario

ETC

ETC ColorSource CYC Manual de usuario

ETC

ETC Source Four Zoom Manual de usuario

ETC

ETC Source Four MultiPAR Manual de usuario

ETC

ETC Express 24/48 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario