ETC ArcSystem Pro D1 Series Manual de usuario

ETC Installation Guide

ArcSystem Pro D1 and D2 Series Drivers

Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000

Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535

Web etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETCintends this document to be provided in its entirety.

7491M2110 Rev F Released 2021-01

Introduction

Congratulations on your purchase of ArcSystem products. ArcSystem is a family of overhead LED

products designed for installations where dimming, light quality, and ease of installation are

absolutely essential. With ArcSystem, you will experience perfectly smooth dimming from 100%

down to absolute zero. ArcSystem luminaires come in a variety of form factors, beam angles, and

color-temperature options, all with high-efficiency optics and an outstanding quality of light ideal for

any application.

ArcSystem products with ArcMesh can be controlled using wired DMX or the wireless ArcMesh

protocol. ArcSystem products without ArcMesh can be configured for RDMcontrol. This manual

provides step by step instruction on the installation of ArcSystem Pro One-Cell luminaires, D1 and D2

Series Drivers, and full system integration. For information on installing ArcSystem Pro D4 Series

Drivers see

the ArcSystem D4 Series Drivers Installation Guide

at etcconnect.com/ArcSystem. For

information on ArcSystem Pro Multi-Cell luminaires, see the

ArcSystem Pro Installation Manual

and

the

ArcSystem Pro Multi-Cell RDMInstallation Guide

at etcconnect.com/ArcSystem.

All ETCmanuals are available for download free of charge at etcconnect.com.

Safety

ArcSystem products are intended for professional use only. Read the entire manual before using this

equipment.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including

the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

•

Do not use outdoors.

•

Do not let power supply cords touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should be mounted in locations and at heights where it will not readily

be subjected to tampering by unauthorized personnel.

•

The use of accessory equipment not recommended by the manufacturer may cause

an unsafe condition.

•

Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 2 of 25 ETC

System Overview

ArcSystem Pro One-Cell luminaires require an external driver.

Models are available to meet your installation requirements. This guide covers the products listed

below.

ArcSystem Pro One-Cell

•

external D1 Series or D4 Series driver required

•

ideal for short/medium throw

•

25 W full load power consumption

•

fixed version recessed/flush mount only

•

adjustable version recessed/flush mount with

two-axis tip and tilt

•

yoke-mount version with single-axis tilt

•

beam angle options: 18°, 30°, 50°

ArcSystem Pro One-Cell Small

•

external D1 Series or D4 Series driver required

•

ideal for short/medium throw

•

25 W full load power consumption

•

adjustable version recessed/flush mount with

single-axis tilt

•

yoke-mount version with single-axis tilt

•

beam angle options: 19°, 24°, 37°, 60°

ArcSystem Pro One-Cell High Output

•

external D1 HO driver required

•

ideal for long throw

•

100 W full load power consumption

•

fixed version recessed/flush mount only

•

adjustable version recessed/flush mount with

two-axis tip and tilt

•

yoke-mount version with single-axis tilt

•

beam angle options: 18°, 30°, 50°

ArcSystem Pro One-Cell Micro

•

external D2 driver required

•

ideal for short/medium throw

•

20 W full load power consumption

•

adjustable version recessed/flush mount with

two-axis tip and tilt

•

yoke-mount version with single-axis tilt

•

beam angle options: 19°, 24°, 37°, 60°

Note:

The ArcSystem Pro One-Cell Micro is not available in 5000 K or Fade to Warm

variants. The ArcSystem Pro One-Cell High Output is not available in 3500K, 4000K,

5000K, or Fade to Warm variants.

ArcSystem Pro multi-cell luminaires are covered in the

ArcSystem Pro Multi-Cell RDMInstallation

Guide

and

ArcSystem Pro Installation Manual

. All ETCmanuals are available for download free of

charge at etcconnect.com.

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 3 of 25 ETC

D1 Series, D2 Series, and D4 Series Drivers

D1 Driver

D1 HO Driver

D2 Driver Wall-Mount D4 Driver 150

(also available in 350 and 700 models)

Rack-Mount D4 Driver 350

(also available in 700 model)

Note:

Antenna is not present on RDM models.

ArcSystem Pro One-Cell luminaires require an external driver. ArcSystem D1, D2, and D4 Series

drivers use standard RJ45 connectors for DMXcontrol.

•

The D1 Driver provides up to 25 W to a single One-Cell or One-Cell Small luminaire.

•

The D1 HO Driver provides up to 100 W to a single One-Cell High Output luminaire.

•

The D2 Driver supports one or two One-Cell Micro luminaires and provides up to 10 W per

output.

For more information on installation of standard or emergency D4 series drivers, see the

ArcSystem

Pro D4 Series Installation Guide

Note:

ArcSystem Pro One-Cell Micro and ArcSystem Pro One-Cell standard luminaires

are not interchangeable. One-Cell Micro luminaires require a D2 driver to function;

One-Cell and One-Cell Small luminaires require a D1 driver or D4 driver to function.

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 4 of 25 ETC

Note:

All ArcSystem wireless luminaires require a TX1 Transmitter and commissioning

tool to set DMX addresses for both wired DMX and wireless installations. Contact your ETC

Service Technician for more information.

TX1 Transmitter

The TX1 Transmitter is the DMX wireless gateway for the ArcMesh

protocol.

One transmitter:

•

Controls up to 100 devices across 64 DMX addresses.

•

Has a 24 preset scene memory.

•

Has DMX wired output for control of third party equipment within

scene store.

•

Has two auxiliary inputs for closed contact connection to trigger a

stored scene.

Each transmitter can be set to one of 16 available network IDs

allowing multiple transmitters to be used concurrently without “cross-

talk.” When two or more transmitters are set to the same network ID

and radio channel, the transmitter with the highest MAC address acts

as a master with the others assuming the role of backup.

For information on installing the ArcSystem TX1 Transmitter for use

with ArcMesh installations, see the ArcSystem Installation Manual at

etcconnect.com/ArcSystem. All ETCmanuals are available for

download free of charge at etcconnect.com.

ArcMesh

ArcSystem products can be controlled using wired DMX through RJ45 connections, or the wireless

ArcMesh protocol. A wireless installation is an ideal solution for retrofit situations where installing

additional cable is not practical.

The following diagram illustrates a basic hybrid ArcSystem installation with a wireless luminaire,

TX1 Transmitter, and a wired DMX console for the main control source.

AC Power

100-240 VAC

Active DMX

output for other

wired devices

DMX512 from

Lighting Control

AUX Input Toggle

Operation

DMX out DMX in

Wireless Luminaire

TX1 Transmitter

Each system requires a minimum of one TX1 Transmitter. The TX1 is used as a transmitter of

wireless data to luminaires or other devices within a system.

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 5 of 25 ETC

Note:

By default the TX1 DMXoutput is disabled. If you require DMX output from the

TX1, you must use the ArcSystem comissioning tool software to add DMXfixtures.

ArcMesh Specifications

•

Use up to 100 devices per TX1 transmitter.

•

Patch up to 64 ArcMesh channels to 512 DMX channels.

•

Use up to 16 TX1 transmitters per system.

There are no system range limitations for transmitting data

between luminaires because each luminaire has the ability to

act as a repeater (see Re-Broadcast Mode below). ArcSystem

is self-regulating and continues to reconfigure the

communication “mesh” to establish the most successful path

of communication transmission.

Re-Broadcast Mode

By default all ArcSystem luminaires are shipped with Re-

broadcast Mode turned off to reduce the amount of wireless

activity. In areas of poor wireless reception, re-broadcast

mode may be enabled on a luminaire-by-luminaire basis to

improve the overall signal level of the system.

CAUTION:

If re-broadcast mode is

required, use this feature in as few

luminaires as possible to avoid unnecessary

traffic on the network and possible system

performance issues.

Emergency System Overview

ArcSystem drivers and luminaires can be purchased in UL924 listed variants. Each of the luminaires

can be configured to be UL924 listed when wired into an existing emergency response system. See

Emergency System One-Cell Installation on page16

Install the luminaire and ArcSystem D1, D2, or D4 Series driver in a location that is accessible by

qualified personnel for testing of the emergency operation.

Note:

Luminaires must be hard-wired to emergency certified drivers to be considered for

UL924 certification.

Note:

The number of designated emergency lamps and their height is the responsibility of

the specifier and installer in order to achieve the minimum FC levels of NFPA101.

Installation scenarios should be evaluated by the AHJ to confirm illuminance and

performance requirements of ANSI/NFPA 101 and the IBC.

Note:

ArcSystem Pro One-Cell Micro luminaires in emergency installations must be

installed with a maximum mounting height of 23.2 ft (7.07 m).

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 6 of 25 ETC

Note:

Installation must follow all national and local codes for electrical equipment.

Note:

Normal and emergency wiring cannot be contained in the same conduit according

to NEC 700.10(B).

Emergency drivers and luminaires require two branch circuit connections. These inputs have the

following functions:

1. Normal branch circuit to sense failure of the normal supply. Connect to Sense Input

connector.

2. Normal/Emergency branch circuit providing power to the luminaire in both conditions.

Connect to Maintained Input connector.

Sense detects when power is lost and forces the luminaire to a full-on state, powered by the

emergency supply through the Constant Power input. Control of the luminaire will not be available

until the sense input has been restored.

WARNING: Do not mix 120 V and 277 V between the sense and emergency

feeds.

AVERTISSEMENT : Ne pas inverser les alimentations à 120V et 277V entre

les alimentations de détection et de secours.

WARNING: Sense (normal) and Maintained (normal/emergency) feeds must

have the same phase. The diagram below shows the recommended installation.

AVERTISSEMENT : Les alimentations de détection (normale) et d’entretien

(normal/secours) doivent être sur la même phase. Le schéma ci-dessous présente

l’installation recommandée.

Typical Installation

The typical installation shown below is suitable for all ArcSystem Pro emergency drivers and

ArcSystem Pro multi-cell emergency luminaires.

normal

breaker

panel

emergency

breaker

panel

normal branch circuit

used to sense normal power failure

normal/emergency branch circuit

normal

normal/emergency

from UL1008

ATS by others

ArcSystem Pro

multi-cell emergency

luminaire or

ArcSystem Pro

One-Cell luminaire

with ArcSystem Pro

series emergency

driver

Sense

Maintained

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 7 of 25 ETC

Installation with DMXBypass Controller

ArcSystem Pro D1, D1 HO, and D2 Series emergency drivers and ArcSystem multi-cell emergency

luminaires that are installed in a system with a DMXbypass controller can have their Maintained

and Sense inputs fed from an emergency lighting transfer switch (UL1008 ATS).

Note:

The installation shown below is not approved for ArcSystem Pro D4 Series Drivers

or ArcSystem ArcLamp Drivers.

DMX

Bypass

Controller ArcSystem Pro

multi-cell emergency

luminaire or

ArcSystem Pro

One-Cell luminaire

with D1, D1 HO, or

D2 series emergency

driver

UL1008

ATS by others

Sense

Maintained

DMX In

DMX/Emergency Bypass DMX

Normal/Emergency Power

Before You Begin Installation

Review the following sections before beginning your ArcSystem installation. ArcSystem products

should only be installed by a qualified installer or electrician.

Power Disconnect Device

Before installation, make sure you have a readily accessible input power disconnect device installed

ahead of your ArcSystem products.

WARNING: RISK OF DEATH BY ELECTRIC SHOCK! Failure to disconnect all

power to the system before installation, maintenance, cleaning, or any other

system modification could result in serious injury or death.

AVERTISSEMENT : RISQUE DE MORT PAR DÉCHARGE ÉLECTRIQUE! Négliger

de débrancher toutes les sources d’alimentation du système avant l’installation,

l’entretien, le nettoyage ou toute autre modification du système peut causer

des blessures graves ou la mort.

De-energize main feed to ArcSystem and follow appropriate Lockout/Tagout

procedures as mandated by NFPA 70E. It is important to note that electrical

equipment such as breaker panels can present an arc flash hazard if improperly

serviced. This is due to the high amounts of short-circuit current available on

the electrical supply to this equipment. Any work must comply with OSHA Safe

Working Practices.

WARNING: Circuits that are installed without an accessible power disconnect

device cannot be serviced or operated safely.

AVERTISSEMENT : Il est imprudent d'utiliser ou de réparer les circuits

installés sans qu'un dispositif de déconnexion de l'alimentation ne soit

accessible.

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 8 of 25 ETC

Site Survey for Wireless Installations

ArcSystem transmitters and luminaires operate in the unlicensed 2.4 GHz band using the IEEE

802.15.4 standard. This band is shared with other technologies such as Wi-Fi, Bluetooth, low power

sensor networks, wireless AV transmitters and some radio microphones.

Before commissioning a system, a wireless site survey is essential.

Gathering information on how your wireless lighting system will overlap with all other Wi-Fi traffic in

the area will help determine setup of transmitters and which luminaires should be re-broadcasting,

not just receiving wireless data.

Installation Requirements

•

Indoor installation only: 0–40°C (32–104°F), 5–95% non-condensing humidity.

•

Dry locations only.

•

Installation location must support the weight of the luminaire, driver, and applicable mounting

hardware.

CAUTION:

ArcSystem luminaires and drivers are not suitable for use in spaces

with restricted air flow. Enclosing the luminaires or drivers temporarily or

permanently may cause damage to the luminaires or drivers.

Preparing the Ceiling for Recessed Luminaires

This section is specific to the recessed/flush mounted variant of luminaires. For Pro One-Cell yoke-

mounted luminaires, proceed to

Installing One-Cell Yoke-Mounted Luminaires on page11

The luminaire retaining clips accommodate 3–24 mm (1/8–15/16 in)ceiling thickness. Cut a hole in

the ceiling or ceiling tile to accommodate the luminaire’s retaining clip anchors. Cut the hole larger

than the minimum hole diameter listed below and smaller than the luminaire’s outer bezel. The

images below provide an example of the bezels on the Pro One-Cell luminaires.

Luminaire Minimum Hole Diameter

Pro One-Cell 16.5 cm (6-1/2 in)

Pro One-Cell High Output 17.0 cm (6-11/16 in)

Pro One-Cell Small 9.5 cm (3-3/4 in)

Pro One-Cell Micro 7.6 cm (3 in)

Note:

If you are installing the luminaire into an ArcSystem Recessed Ceiling Adapter,

refer to the

ArcSystem Recessed Ceiling Adapter Installation Guide

for the minimum

diameter hole to cut in the ceiling to clear the flange on the bottom of the bracket.

Note:

Maximum ceiling thickness for safe use of the luminaire retaining clips is 24mm

(15/16in).

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 9 of 25 ETC

Pro One-Cell

fixed model

Pro One-Cell

adjustable model

B B

Pro One-Cell Small

adjustable model

Pro One-Cell High Output

adjustable model

Pro One-Cell Micro

adjustable model

AOuter bezel

BInner bezel

Installation Spacing - High Output Luminaires

If you are installing ArcSystem Pro One-Cell High Output luminaires, plan the luminaire and driver

locations around the required spacing listed below.

Install with minimum spacings between

a. Center-to-center of adjacent luminaires:609.6mm (24in);

b. Top of luminaire to overhead building member:76.2mm (3in);

c. Luminaire center to side building member:304.8mm (12in);

Assurer les dégagements minimaux suivants

a. Entre l'entraxe des luminaires adjacents 609.6mm (24po)

b. Entre le dessus du luminaire et l'élément de charpente se trouvant au-dessus 76.2m (3po)

c. Entre le centre du luminaire et un élément de charpente 304.8mm (12po)

ETC Installation Guide

D1 & D2 Series Drivers

D1 & D2 Series Drivers Page 10 of 25 ETC

Installing One-Cell Recessed Luminaires

The installation procedure is similar for all recessed one-cell luminaires (fixed and adjustable). For

Pro One-Cell yoke-mounted luminaires, continue on to

Installing One-Cell Yoke-Mounted

Luminaires on the facing page

WARNING: ArcSystem Pro One-Cell, One-Cell Small, and One-Cell High

Output fixtures and D1 and D1 High Output drivers are NON-IC rated and

therefore NOT suitable for installation in direct contact with combustible

materials or thermal insulation.

DO NOT INSTALL INSULATION WITHIN 76 mm (3 in) OF ANY PART OF THE

FIXTURE OR DRIVER.

AVERTISSEMENT : Les lampes One-Cell, One-Cell Small, One-Cell High

Output, et les drivers D1 and D1 High Output ArcSystem sont classés NON-IC, ils

ne conviennent donc PAS pour une installation en contact direct avec des

matières combustibles ou une isolation thermique.

NE PAS INSTALLER D’ISOLATION À MOINS DE 76mm (3po) DE TOUTE PARTIE

DE LA LAMPE OU DU DRIVER (DISPOSITIF ÉLECTRONIQUE DE PUISSANCE).

WARNING: Adjustable ArcSystem Pro One-Cell fixtures and adjustable

ArcSystem Pro One-Cell Small fixtures are suitable for Non-Fire Rated

installations ONLY.

AVERTISSEMENT : Les lampes Pro One-Cell ArcSystem réglables et Pro One-

Cell Small ArcSystem réglables sont parfaites UNIQUEMENT pour les

installations sans indice de résistance au feu.

Note:

Make sure that the flexible electrical supply can extend through the ceiling

opening so that the driver and luminaire can be inspected and serviced when needed.

Note:

ArcSystem Pro One-Cell Micro luminaires and D2 drivers are Type IC - inherently

protected and suitable for installation in contact with insulation.

1. Fold both retaining clips towards the luminaire body.

2. Place the luminaire through hole.

3. Release the clips, securing the luminaire in place.

4. When applicable, rotate the luminaire so it is roughly

focused to its final resting position. This will assist in

final focus procedures.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de ETC

ETC

ETC Expression 2.0 Manual de usuario

ETC

ETC Selador Series Manual de usuario

ETC

ETC Source Four Revolution Scroller Cartridge Manual de usuario

ETC

ETC source four fresnel Manual de usuario

ETC

ETC ColorSource CYC Manual de usuario

ETC

ETC Source Four PARNel CE Manual de usuario

ETC

ETC ColorSource Spot Manual de usuario

ETC

ETC IRIDEON AR500 Manual de usuario

ETC

ETC HIGH END SYSTEMS SolaPix 37 Manual de usuario

ETC

ETC Express Manual de usuario

ETC

ETC Irideon AR50 Manual de usuario

ETC

ETC Express 24/48 Manual de usuario

ETC

ETC High End Systems SolaPix 19 Manual de usuario

ETC

ETC fos/4 Panel Yoke Manual de usuario

ETC

ETC fos/4 Series Manual de usuario

ETC

ETC F-Drive W1 Series Manual de usuario

ETC

ETC SolarFrame 750 Manual de usuario

ETC

ETC Echo Manual de usuario

ETC

ETC fos/4 Fresnel Manual de usuario

ETC

ETC microVision FX Manual de usuario

ETC

ETC Source Four HID PARNel Manual de usuario

ETC

ETC Sensor IQ DALI Control Option Card Manual de usuario

ETC

ETC Lustr+ Manual de usuario

ETC

ETC fos/4 Series Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario