ESI LTH-EDGE Manual de usuario
INSTALLATION AND ADJUSTMENT
LTH-EDGE
ADJUSTABLE LAPTOP TRAY
LTH-EDGE Rev A 2/17
Model LTH-EDGE-SLV
2
LAPTOP TRAY INSTALLATION
PLEASE REVIEW these instructions before beginning the installation. Check that
all parts shown below were provided with your order. Contact your supplier
if any parts are missing. Do not discard the packaging until satised that the
product operates to your satisfaction.
The LTH-EDGE adjustable laptop tray is used with an EDGE monitor arm. It is
installed in place of a monitor. Refer to the instructions that came with the
monitor arm for assembly and adjustment procedures for the EDGE system.
TOOLS REQUIRED
• Phillips screwdriver
• Pliers
PARTS PROVIDED
CAUTION: Hand-tighten screws only. Do not use power tools.
Laptop Tray (1) Laptop Tray Nonskid Pad (2)
Laptop Tray Screw (4)
Laptop Tray Locking Nut (4)
1
/8x1
/4-32
3/8x1
/4-32
3
LAPTOP TRAY INSTALLATION
If the EDGE Monitor Arm Currently Has a Monitor Attached:
Remove the Monitor
• Disconnect the monitor cables.
• If a VESA locking screw is installed, remove the screw.
• Press down on the plastic tab on the VESA mount to release the VESA plate.
• Lift the monitor and VESA plate from the VESA mount.
Remove the VESA Plate from the Monitor
• Place the monitor face down
• Remove the four screws that
attach the VESA plate to the
monitor.
• Remove the VESA plate.
Proceed to "Attach the VESA Plate to the Laptop Tray" on page 4.
Remove
VESA
Locking
Screw
1.
2.
VESA
Plate
Screw VESA Plate
Monitor
(Face Down)
Upward
4
LAPTOP TRAY INSTALLATION
If No Monitor Is Attached to the EDGE Monitor Arm:
Remove the VESA Plate from the
VESA Mount
• Press down on the plastic tab to
release the lock.
• Pull the plate upward to remove.
Attach the VESA Plate to the Laptop Tray
• Align the VESA plate holes with the holes on the back of the laptop tray.
Attach the VESA plate using the four laptop tray screws and locknuts
provided.
— There are two sets of four holes on the VESA plate. One set has holes
3.9" (100mm) apart, the other set has holes 3" (75mm) apart. Either set of
holes may be used.
VESA
Plate 1.
2.
VESA
Plate
Laptop
Tray
1
/8x1
/4-32
3/8x1
/4-32
5
LAPTOP TRAY INSTALLATION
Attach the Laptop Tray to the VESA Mount
• Slide the VESA plate and laptop tray onto the VESA mount. Make sure the
VESA plate clicks securely in place.
— Optional: Install a VESA locking screw behind the VESA plate to prevent
the tab on the VESA mount from releasing the laptop tray.
VESA
Locking
Screw
(Optional)
6
LAPTOP TRAY INSTALLATION
Laptop Tray Adjustment
• Loosen the two knobs on the underside of the laptop tray to adjust for the
desired depth.
— The laptop tray adjusts from 12" to 18¼" in depth to accommodate a
laptop alone or a laptop with docking station.
• Apply the two nonskid pads to the tray surface to help secure the laptop.
— Peel the adhesive packing from the pads and press them rmly in place.
Nonskid
Pads
Loosen
Knobs to
Adjust
800.833.3746esiergo.com
© 2017 ESI Ergonomic Solutions. All rights reserved. LTH-EDGE Rev A 2/17
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Rack y soporte de ESI
ESI
ESI Kata2-MS Series Manual de usuario
ESI
ESI E-AMT Manual de usuario
ESI
ESI EVOLVE Series Manual de usuario
ESI
ESI Kata Series Manual de usuario
ESI
ESI EVOLVE Series Instrucciones de instalación
ESI
ESI Kata EX2-MS Series Manual de usuario
ESI
ESI Kata EX2-FMS Manual de usuario
ESI
ESI EPPA2-KIT Manual de usuario
ESI
ESI LIFT ERGORISE Manual de usuario
ESI
ESI AA355DS Manual de usuario
