ESAB Origo M 12 Feed 304 Manual de usuario

Valid for serial no. 620-xxx-xxxx, 917-xxx-xxxx0459 161 101 GB 20120621

Origo™ M12

Feed 304

Feed 484

Instruction manual

-2-

- 3 -

TOCe

Rights reserved to alter specifications without notice.

1 SAFETY 4...........................................................

2 INTRODUCTION 5...................................................

2.1 Equipment 6................................................................

3 TECHNICAL DATA 6.................................................

4 INSTALLATION 7....................................................

4.1 Lifting instructions 7.........................................................

5 OPERATION 8.......................................................

5.1 Connections and control devices 9............................................

5.2 Water connection 9..........................................................

5.3 Starting procedure 9.........................................................

5.4 Function explanations 10......................................................

5.5 Wire feed pressure 11........................................................

5.6 Changing / loading wire Feed 304 11............................................

5.7 Changing / loading wire Feed 484 11............................................

5.8 Chaning feed rollers on Feed 304 12............................................

5.9 Changing feed rollers on Feed 484 12...........................................

6 MAINTENANCE 13....................................................

6.1 Inspection and cleaning 13....................................................

7 ORDERING SPARE PARTS 13.........................................

DIAGRAM 14............................................................

ORDER NUMBER 19.....................................................

WEAR PARTS 20........................................................

ACCESSORIES 25.......................................................

- 4 -

bm33d1ea

1 SAFETY

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or

near the equipment observes all the relevant safety precautions. Safety precautions must meet the

requirements that apply to this type of equipment. The following recommendations should be ob

served in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the equip

ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in

jury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

its operation

location of emergency stops

its function

relevant safety precautions

welding and cutting

2. The operator must ensure that:

no unauthorised person is stationed within the working area of the equipment when it is

started up.

no-one is unprotected when the arc is struck

3. The workplace must:

be suitable for the purpose

be free from drafts

4. Personal safety equipment

Always wear recommended personal safety equipment, such as safety glasses, flame-proof

clothing, safety gloves.

Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

Make sure the return cable is connected securely.

Work on high voltage equipment may only be carried out by a qualified electrician.

Appropriate fire extinquishing equipment must be clearly marked and close at hand.

Lubrication and maintenance must not be carried out on the equipment during operation.

ESAB can provide you with all necessary welding protection and accessories.

CAUTION

Read and understand the instruction manual before

installing or operating.

CAUTION

Class A equipment is not intended for use in residential locations where

the electrical power is provided by the public low-voltage supply system.

There may be potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations, due to conducted

as well as radiated disturbances.

- 5 -

bm33d1ea

CAUTION

This product is solely intended for arc welding.

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and

cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard

data.

ELECTRIC SHOCK - Can kill

Install and earth the unit in accordance with applicable standards.

Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

Insulate yourself from earth and the workpiece.

Ensure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

Keep your head out of the fumes.

Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

Protect bystanders with suitable screens or curtains.

FIRE HAZARD

Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

Warn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical and/or

electronic equipment that has reached the end of its life must be disposed of at a

recycling facility.

As the person responsible for the equipment, it is your responsibility to obtain

information on approved collection stations.

For further information contact the nearest ESAB dealer.

2 INTRODUCTION

The Feed 304 and Feed 484 wire feed units with control

panel M12 are intended for MIG/MAG-

welding together with stepped welding power sources.

They come in different variants, see the spare parts list on

page 19.

The wire feed units are sealed and contain four-wheel

drive wire feed mechanisms as well as control electronics.

They can be used together with wire on ESAB's

MarathonPac, or on wire bobbin (standard Ø 300 mm, accessory Ø 440 mm).

- 6 -

bm33d1ea

The wire feed unit can be installed either at the power source, suspended above the

workplace, on a support arm or on the floor with or without wheel set.

ESAB's accessories for the product can be found on page 25.

2.1 Equipment

The Feed 304 wire feed unit is supplied with:

Instruction manual

Stickers with recommended wear parts.

The Feed 484 wire feed unit is supplied with:

Spacer (4)

Hex key wrench (4 mm)

Instruction manual

Stickers with recommended wear parts.

3 TECHNICAL DATA

Feed 304 Feed 484

Power supply 42 V 50 - 60 Hz 42 V 50 - 60 Hz

Power requirement 336 VA 378 VA

Motor current Imax 8 A 9 A

Settings data

Wire feed speed

Burnback time

Creep start

2/4 stroke

1.9-25.0 m/min

0-0.5 s

OFF or ON

2 stroke or 4 stroke

1.9-25.0 m/min

0-0.5 s

OFF or ON

2 stroke or 4 stroke

Welding gun connection EURO EURO

Max. diameter wire bobbin 300 mm (*440mm) 300 mm (*440mm)

Wire dimension 0.6-1.6 mm 0.6-2.4 mm

Weight

basic version

with sealed bobbin holder

11.5 kg

15 kg

14.5 kg

19 kg

Dimensions (l x w x h)

basic version

with sealed bobbin holder

380 x 275 x 400 mm

690 x 275 x 420 mm

380 x 275 x 400 mm

690 x 275 x 420 mm

Shielding gas

max pressure

All types intended for

MIG/MAG welding

5 bar

All types intended for

MIG/MAG welding

5 bar

Coolant

max pressure

50% water / 50% glycol

5 bar

50% water / 50% glycol

5 bar

Permissible load at

60% duty cycle 630 A 630 A

Enclosure class

with wire bobin *440mm

IP23

IP2X

IP23

IP2X

* Accessory, see page 25.

- 7 -

bm33d1ea

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at

a certain load without overloading. The duty cycle is valid for 40°C.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Equipment marked IP2X is designed for indoor use.

4 INSTALLATION

The installation must be carried out by a professional.

CAUTION

This product is intended for industrial use. In a domestic environment this product may

cause radio interference. It is the user's responsibility to take adequate precautions.

WARNING

When welding in an environment with increased electrical danger, only power

sources intended for this environment may be used. These power sources are

marked with the symbol

4.1 Lifting instructions

Ordering number for the lifting eye can be found on page 25.

Note! If another mounting device is used, this should be insulated from the wire feed

unit.

- 8 -

bm33d1ea

5 OPERATION

General safety regulations for handling the equipment can be found on

page 4. Read through before you start using the equipment!

WARNING

Assure that the side panels are closed during operation.

WARNING

To prevent the reel from sliding off the hub: Lock the

reel in place by turning the red knob as shown on the

warning label attached next to the hub.

WARNING

Rotating parts can cause injury, take great care.

WARNING

Risk of crushing when replacing the wire bobbin!

Do not use safety gloves when inserting the welding wire between the feed rollers.

WARNING

There is a risk of tipping if the wire feed unit is fitted with a counterbalance arm.

Secure the equipment, especially if used on an uneven or sloping surface.

NOTE: When moving the equipment use intended handle. Never pull on the gun.

- 9 -

bm33d1ea

5.1 Connections and control devices

1Knob for setting burnback time 8Connection for welding gun

2Switch for creep start OFF / ON 9Connection for welding current from power

source, (OKC)

3Knob for setting wire feed speed 10 Connection for control cable from power

source

4Switch for 2-stroke / 4-stroke 11 Connection RED for cooling water to

power source (cooling unit)

5Connection for remote control unit 12 Connection BLUE for cooling water from

power source (cooling unit)

6Connection BLUE, with ELP* for cooling

water to welding gun

13 Connection for shielding gas

7Connection RED for cooling water from

welding gun

NOTE! Cooling water connections only available on certain models.

* ELP = ESAB Logic Pump, see point 5.2.

5.2 Water connection

When connecting a water-cooled welding gun, the power source's main power

supply switch must be in the Off position and the cooling unit switch must be in

position “ELP/0”.

The wire feed unit with water connection is equipped with a detection system ELP

(ESAB Logic Pump) which checks that the water hoses are connected. When

connecting a water-cooled welding gun, the water pump starts.

Detection only works with power sources that are equipped with ELP.

5.3 Starting procedure

When the wire feed starts, the power source generates welding voltage.

If there is no welding current flow within three seconds, the power source switches the

welding voltage off. The wire feed continues until the welding gun's switch is switched

off.

- 10 -

bm33d1ea

5.4 Function explanations

Burnback time

Burnback time is a delay between the time when the wire starts to brake until the

time when the power source switches off the welding voltage. Too short burnback

time results in a long wire stickout after completion of welding, with a risk of the wire

being caught in the solidifying weld pool. Too long a burnback time results in a

shorter stickout, with increased risk of the arc striking back to the contact tip.

Creep start

Creep start means that the wire is fed at low speed until it comes into electrical

contact with the workpiece and then the speed increases to the set speed.

2 stroke

With 2 stroke, the gas flow and wire feed start when the trigger switch is pressed in

and end when it is released.

4 stroke

With 4 stroke, the gas flow starts when the trigger switch is pressed in and the wire

feed starts when it is released. The welding process continues until the switch is

pressed in again, the wire feed stops and when the switch is released the gas stops

flowing.

Wire feed speed

This sets the required feed speed of the filler wire in m/minute.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de soldadura de ESAB

ESAB

ESAB Aristo U6 Manual de usuario

ESAB

ESAB Heliarc 283i AC/DC Manual de usuario

ESAB

ESAB Thermal Dynamics CUTMASTER 40 Manual de usuario

ESAB

ESAB Mig 4004 iMV Guía

ESAB

ESAB SCT-1500 SERIES Manual de usuario

ESAB

ESAB ESABMig C240 Manual de usuario

ESAB

ESAB Renegade ET 300iP Manual de usuario

ESAB

ESAB MultiMaster 160 Manual de usuario

ESAB

ESAB RS 400x Manual de usuario

ESAB

ESAB PowerCut 400 Manual de usuario

ESAB

ESAB Aristo Origo Feed 3004 Manual de usuario

ESAB

ESAB WeldCloud Mobile Manual de usuario

ESAB

ESAB EMP 205ic AC/DC Manual de usuario

ESAB

ESAB Origo Feed 304N P4 Manual de usuario

ESAB

ESAB AristoFeed 30- 4 Manual de usuario

ESAB

ESAB 0459230883 Manual de usuario

ESAB

ESAB Caddy Tig 1500i Manual de usuario

ESAB

ESAB Warrior 400i CC/CV Manual de usuario

ESAB

ESAB RobustFeed PRO Manual de usuario

ESAB

ESAB Origo Mig C141 Manual de usuario

ESAB

ESAB Origo Arc 456 Series Guía

ESAB

ESAB MIG-41 Manual de usuario

ESAB

ESAB ET 300i Manual de usuario

ESAB

ESAB LHJ 750 Guía

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario