ESAB ARC 601i Manual de usuario

ARC 601i

INVERTER MMA / GOUGING

Welding Power Source

Instruction manual

Ver: 1.0 0421

ARC 601i

INVERTER WELDING POWER SOURCE

Instruction manual

For

Installation, Operation & General maintenance

CONTENTS

Item

Page No.

SAFETY

3-4

RATING AND INSTALLATION

5-6

CAUTIONS FOR INSTALLATION

WELDING OPERATIONS

8-9

WIRING DIAGRAM

GENERAL MAINTENANCE

PARTS LIST AND EXPLODED VIEW

12-15

ESAB INDIA CONTACT DETAIL

SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that

anyone who works on or near the equipment observes all the relevant safety

precautions. Safety precautions must meet the requirements that apply to this type of

welding equipment. The following recommendations should be observed in addition to

the standard regulations that apply to the workplace.

Trained personnel well acquainted with the operation of the welding equipment must

carry out all the work. Incorrect operation of the equipment may lead to hazardous

situations, which can result in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

• its operation

• location of emergency stops

• its function

• relevant safety precautions

• welding

2. The operator must ensure that:

• no unauthorized person is stationed within the working area of the equipment

when it is started up.

• no one is unprotected when the arc is struck

3. The workplace must:

• be suitable for the purpose

• be free from drafts

4. Personal safety equipment

• Always wear recommended personal safety equipment, such as safety glasses,

flameproof clothing, and safety gloves.

• Do not wear loose—fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns.

5. General precautions

• Make sure the return cable is connected securely.

• Only a qualified electrician may carry out work on high voltage equipment.

• Appropriate fire extinguishing equipment must be clearly marked and close at

hand.

• Lubrication and maintenance must not be carried out on the equipment during

operation.

Read and understand the instruction manual before installing or operating.

ESAB can provide you with all necessary welding protection and accessories.

WARNING

Arc welding and cutting can be injurious to yourself and others. Take

precautions when welding.

Ask for your employer’s safety practices which should be based on manufacturers’

hazard data.

ELECTRIC SHOCK –Can kill

• Install and earth the welding unit in accordance with applicable

standards.

• Do not touch live electrical parts or electrodes with bare skin, wet

gloves or wet clothing.

• Insulate yourself from earth and the workpiece.

• Ensure your working stance is safe.

FUMES AND GASES –Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS –Can injure eyes and burn skin.

• Protect your eyes and body. Use the correct welding screen and filter

lens and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure therefore that there are no

inflammable materials nearby.

NOISE –Excessive noise can damage hearing

• Protect your ears. Use earmuffs or other hearing protection.

• Warn bystanders of the risk.

MALFUNCTION –Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding

Do not dispose of electrical equipment together with normal waste!

In accordance with national law, electrical equipment that has

reached the end of its life must be collected separately and returned

to an environmentally compatible recycling facility. As the owner of

the equipment, you should get information on approved collection

systems from the local representative. By applying this Directive you

will improve the environment and human health

RATING

RATING OF ARC 601i INVERTER WELDING POWER SOURCE

Contents of parameters

Unit

ARC601i

Output

No-load voltage

Working voltage

22-44

Rated welding current

600

Welding current

regulating range

50-600

Rated load duty cycle

100%

60%

520A

600A

Input

Number of phases

Phase

Frequency

50/60

Power supply voltage

415

Rated input current

Maximum effective

input current

34.8

Rated input capacity

KVA

31.63

≥85%

Insulation level

Enclosure protection grade

IP21S

Characteristics

Drooping characteristic

Weight

Dimensions (L* W* H)

680×320×581

INSTALLATION

Input wiring

oEnsure that the voltage, number of phases, frequency and capacity of the input

power are consistent with the calibration values on the nameplate of the welding

machine.

oWiring shall be performed by professional electrician.

oThe input cable and air inlet are located on the back panel of the welding machine.

Please refer to the structure diagram of welding machine for detailed location.

oConnect the input cable to the power to ensure the reliable connection.

oThe casing must be grounded, and the grounding bolt is located at the lower right

corner of the back panel of the welding machine and marked with a grounding

mark.

oThe recommended specifications of ground wire, fuse protector or breaker are as

follows:

Specifications for input cables, grounding wires and input fuse protectors or circuit

breakers at 3-phase /50Hz rated load duty cycle

Welding

machine

model

Duty cycle

Input

voltage

Input

current

Most

effective

Input

current

Cable specification

Fuse

protector

circuit

breaker

Three-phase

input cable

Grounding

wire

ARC601i

60%

415V

45A

34.8A

>4 mm2

>2.5 mm2

63A

Output connection

oThe positive and negative electrodes of the output terminal are located at the

lower part of the front panel and marked with "+" and "-" symbols.

oConnect one end of the negative output cable to the negative terminal, and the

other end to the job.

oConnect one end of the positive output cable to the positive terminal, and the

other end to the electrode holder.

CAUTIONS FOR INSTALLATION

−Provide a Switch Box for every Welding Power Source, and use designated

fuse

−Tolerance of Power Voltage Variation is 10% of rated input voltage.

a) Installation place

−Install in the place where less moisture and dust exist. Avoid direct sunlight and

rain and maintain ambient temperature within –10o to +45o C as much as

possible.

−Keep the welding power source at least 20 cm. away from the wall (if any).

−In case of installation of more two units’ side by side, a distance of more than

20 cm is recommended between the two power sources.

−Use a shield to protect the welding arc in case of excessive air draft.

b) Ventilation

Adequate ventilation is recommended at the place of installation. For

example, the following guideline should be followed:

a) In case of the area being more than 300 square meters (per unit), no

ventilation is required, provided the room is not completely airtight.

b) In case of the area being less than 300 square meters and the welding

is continuously performed, adequate ventilation is recommended with

the help of vent fan or exhaust duct.

c) While performing the grounding work, it is recommended that a skilled

electrician does the work.

WELDING OPERATIONS

oThe power switch of the welding machine is located on the upper part of the

rear panel of the welding machine.

oTurn on the power switch of the welding machine and the welding machine will

be on.

oThe power indicator light of the welding machine on the front panel will be on

(the green light will be on), the digital display will display value, the fan will start

running, and the output voltage will be available.

Front Panel

GOUGING / MMA

MMA or GOUGING mode of operation can be selected, selected LED will be on.

LOCAL / REMOTE

LOCAL MODE: Output current control can be done from panel.

REMOTE MODE: Output current control can be done from remote controller.

CURRENT

Welding / gouging current can be controlled in local mode.

ARC FORCE

Arc force can be controlled by rotating this knob. Droplet transition performance can

be improved.

HOT START

Arc striking performance can be improved.

VRD ON / VRD OFF

VRD function can be switched to ON or OFF condition.

Digital display will show output current value in AMP and output voltage value in Volt.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de soldadura de ESAB

ESAB

ESAB ES 180i Manual de usuario

ESAB

ESAB Powercut 900 Manual de usuario

ESAB

ESAB ES 150i Manual de usuario

ESAB

ESAB Origo Mig C420 PRO Manual de usuario

ESAB

ESAB OCF 2L Manual de usuario

ESAB

ESAB 100i Manual de usuario

ESAB

ESAB Rustler EM 280C PRO Manual de usuario

ESAB

ESAB Caddy Arc 201i Manual de usuario

ESAB

ESAB EMP 205ic AC/DC Actualización de firmware

ESAB

ESAB 453cc Manual de usuario

ESAB

ESAB ESABMig C280 Manual de usuario

ESAB

ESAB LHJ 750 Manual de usuario

ESAB

ESAB Aristo 500ix Manual de usuario

ESAB

ESAB EMP 205ic AC/DC Manual de usuario

ESAB

ESAB Caddy Tig 1500i Manual de usuario

ESAB

ESAB PCM-1125 Manual de usuario

ESAB

ESAB Caddy Mig C200i Manual de usuario

ESAB

ESAB POWERCUT-1500 Manual de usuario

ESAB

ESAB PKB 250 Manual de usuario

ESAB

ESAB Heliarc 161 Manual de usuario

ESAB

ESAB fabricator 211i Manual de usuario

ESAB

ESAB PKB 250 Manual de usuario

ESAB

ESAB Buddy Arc 200 Manual de usuario

ESAB

ESAB Aristo Arc 4000i Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario