Erreka KAIROS Manual de usuario

KAIROS

Elementos de la instalación completa

170

180

120 130 140 150 160

AB170 180110

160

150

140

130

120

110

110°~120°

100°~110°

90°~100°

>120°

Quick Installation Guide MSB-029/02

WARNING

This quick guide is a summary of the complete installation manual. The manual contains safety warnings and

other explanations which must be taken into account. The installation manual can be downloaded by going

to the "Downloads" section of Erreka website:

http://www.erreka-automation.com

Elements of the complete installation

Electrical Wiring

A.B: 24v DC Motor(2x1mm²)

C: Photocell 2x0.5mm² (max 20m)

D: Control Box (3x1.5mm²)

E: Push Botton 2x0.5mm²(max 25m)

TATA

E F

Assembly levels, inward opening

KAIROS It is not applicable to an insecure or lacking rigidity door nor solves the defects due to incorrect installation or

Check the following points before starting the installation:

1). Hinges are properly positioned and greased.

2). No obstacles in the moving area and no frictions between two gate leafs or with the ground while moving.

3). “C” value is 139mm.

4). “D” can be measured from the gate easily.

5). “A” = “C” + “D”

6). The value of “B” can be calculated from the value of “A” and the leaves opening angle.

Ex. If “A”=160mm with the leaves opening angle of 100 degrees, then the value of “B” is approximate 190mm.

Please make sure B and A are similar or the same in value that the leaves can be

operated smoothly, also to reduce the burden of the motor.

Open Interior

F: Key Selector(2x0.5 mm²)

G: Flash Light (2x0.5mm²)

H.I: Electric Lock (2x1mm²)

TA: Open Stopper

TC: Close Stopper

TC H

Unlocking

Push the lid of release chamber

Turn counterclockwise the knob.

Insert the key and turn counterclockwise

to the unlock position

Unlocking for manual operation:

Motorised operation locking:

Then turn clockwise the knob to

release the motor.

12 3

Insert the key and turn clockwise. Close the lid of release chamber.

1 2 3

Please make sure B and A are similar or the same invaluethat the leaves can be operated smoothly,

also to reduce the burden of the motor.

Assembly levels, outward opening

Open Exterior

Assembly

Check the door manually which can be moved easily in

entire route.

Fix the front bracket. Check the motor is completely leveled.

and mounting position.

no.1

1 2 3

7 8

5 6

Block the motor and make the electrical wiring. To connect the cables M1 and M2 correctly. If you only

install one gate, connect the wires to the terminal M1.

Horizontal 180O

no.2

Technical Features

Dimensions

917mm

877mm

124mm123mm

350 5mm

Max gate length

Max gate weight

Power supply

Motor power supply

Gear Type

Peak Thrust

Normal Thrust

Operation Stroke

Piston extention

Opening Time

Duty Cycle

Protection Grade (IP)

Operation temperature

Absorbed current (A)

Absorbed Power (W)

Manual Release

Dimensions

300kg

110V/230VAC (50-60Hz) SMART-D201M / SMART-D201

24VDC

Worm and worm gear

3000N

2500N

350mm

25.5mm/sec

<14 sec

20%

IP44

-20oC~50oC

5,5 A for a 10 sec. max.

144W

key

917mm * 123mm * 124mm

(+)

(-)

A1 B2

(+)

(-)

M2-M1-

Lat-

Lit- Lmt4Lmt3

Lmt2

Lit+ SKey

M2+

M1+Lat+ Ph2Ph1 PhVcc PhVcc

S25V

ANT

GND

DKey GND

GND GND GND

Lmt1 GND

K2K1

J4 J3

NC NO

+-- +

NONC

- +

NONCNC NO

1 2 3 4 5 6 7 8

910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

LED3

LED4

LED2

LED Azul-Memorización Radio

LED2 Pulsador o Selector de llave

LED3 Fotocélula 1

LED4 Fotocélula 2

Electrical connections SMART-D201 (M)

Electrical connections VIVO-D203 (M)

A1 Operator 1

A2 Operator 2

G1/G4 Red cable (motor)

G2/G5 Blue cable (motor)

SW1 Main switch

● Select the number of operators using C0 (C001: one operator, C002: two operators).

● Select the directions using C1 (A1) and C2 (A2).

● Programme C7 for operation without encoder or limit switches (C700).

● Adjust the trapping force in accordance with the weight of the gate (parameter A6).

Turning direction check: after connecting the power and activating any of the key devices, the

gate makes a reset (the display shows rS): the gate closes until it reaches the stopper, assigning this

stopper with the position "gate closed" If it opens instead of closes during the reset, change turning

direction using C1 (A1) or C2 (A2).

A1 Operator 1

A2 Operator 2

5/7 M1+ Operator 1/ M2+ Operator 2

6/8 M1- Operator 1/ M2- Operator 2

● Select the number of operators using F2 (F22: one operator, F21: two operators).

● Confirm gate opening direction of A1 and A2 during system programing (first operation is close),

if does not correspond, change the cable connection M+ and M- of corresponding.

● Programme F1 for operation without encoder or limit switches (F11).

● Adjust the trapping force in accordance with the weight of the gate (parameter F3).

Maximum trapping force during system learning process: please make sure the parameter F3“

Maximum trapping force” is in F3-1 during the open/close programming.

VIVO-D203:

VIVO-D203M:

Tabla de contenidos

Otros manuales de Abridor de puerta de Erreka

Erreka

Erreka Dolfin Instrucciones de funcionamiento

Erreka

Erreka VIVO-M201M Instrucciones de funcionamiento

Erreka

Erreka IZAR Guía del usuario

Erreka

Erreka DINGO Instrucciones de funcionamiento

Erreka

Erreka DINGO Instrucciones de funcionamiento

Erreka

Erreka VULCAN S Manual de usuario

Erreka

Erreka ARES Series Guía del usuario

Erreka

Erreka TOPO Guía del usuario

Erreka

Erreka CICLON Guía del usuario

Erreka

Erreka VIVO-M101 Instrucciones de funcionamiento

Erreka

Erreka VULCAN D Instrucciones de funcionamiento

Erreka

Erreka Puma Guía del usuario

Erreka

Erreka MAGIC Instrucciones de funcionamiento

Erreka

Erreka VIVO-D102 Instrucciones de funcionamiento

Erreka

Erreka ARC Series Guía del usuario

Erreka

Erreka SIRIUS Instrucciones de funcionamiento

Erreka

Erreka ARC Series Guía del usuario

Erreka

Erreka CAT Instrucciones de funcionamiento

Erreka

Erreka PUMA-I Instrucciones de funcionamiento

Erreka

Erreka MAGIC Instrucciones de funcionamiento

Erreka

Erreka Puma Instrucciones de funcionamiento

Erreka

Erreka DINGO Manual de usuario

Erreka

Erreka CICLON Series Instrucciones de funcionamiento

Erreka

Erreka Fenix Guía del usuario

Manuales populares de Abridor de puerta de otras marcas

Elite

Elite CSW200UL Manual de usuario

CAME

CAME FROG-PM4 Manual de usuario

SOMFY

SOMFY FX230 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Manual de usuario

Turnstiles

Turnstiles FSW 900 Manual de usuario

Beninca

Beninca R1-2 WBV Manual de usuario

Motorline professional

Motorline professional FORT Manual de instrucciones

Beninca

Beninca BOB5024 Manual de usuario

AGA

AGA GATEMASTER 900 HD Manual de usuario

Chamberlain

Chamberlain MotorLift HC280ML Manual de usuario

SOMFY

SOMFY Dexxo RTS Pro Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Westfalia

Westfalia 85 27 06 Manual de usuario

CAME

CAME F500 Manual de usuario

Extel

Extel VERA Manual de usuario

Comunello Automation

Comunello Automation ABACUS 220 Manual de usuario

CAME

CAME FA40230CB Manual de usuario

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Manual de usuario