ERA VALIANT Manual de usuario

INSTALLATION AND

OPERATING MANUAL

Version 1.0

VALIANT

Solar Siren Alarm Kit

ERA - VALIANT-Red Lens

DoP No: EM0017

IMPORTANT

PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING

THE SYSTEM AND RETAIN FOR FUTURE REFERENCE.

All devices, with the exception of the external siren are suitable for mounting

in dry interior locations only.

Any repairs must be carried out by an Authorised Repair Centre. Misuse

or attempted repairs to a component part of the product will invalidate the

warranty. The photocopying, copying, reproduction, translation to any language,

modification, storage in a retrieval system or retransmission, in whole or in part,

in any form or by any means, electronic, mechanical or otherwise of this manual,

is strictly prohibited without the prior written permission of ERA Home Security.

Disposal and Recycling

Disposal of this product is covered by the Waste Electrical or Electronic Equipment

(WEEE) Directive. It should not be disposed of with other household or commercial

waste.

At the end of the product’s useful life, the packaging and product should be disposed

of via a suitable recycling centre. Please contact your local authority or the retailer

from where the product was purchased for information on available facilities.

Declaration of Performance

This equipment complies with the essential requirements of the Radio and

Telecommunications Terminal Equipment Directive, 1999/5/EC.

Additional Accessories

This can easily be extended at any time with the range of ERA Wireless Alarm

Accessories for details visit www.erahomesecurity.com or call our Customer

Support team on 0345 257 2500 (local call rate).

Page 1

Specifications

1.1 Get to know your product

1.2 LED Indication

1.3 PCB Layout

1.4 Test Mode

1.5 Working Mode

1.6 Installation

1. PIR Motion Detector

TABLE OF CONTENT

2.1 Get to know your product

2.2 PCB Layout

2.3 Installation

4.1 Positioning

4.2 PCB Layout

4.3 Jumper Setup

4.4 Usage

4.5 Installation

4.6 Jamming Detection

6. Notes 12

ERA Product Guarantee 13

5. Specification

4. Solar Charged Siren

3.1 Get to know your product

3.2 Buttons/Functions

2. Magnetic Door/Window Sensor

3. Remote Control

Kit Contents

Page 2

Wireless Solar Siren x 1

Door/Window Sensor x 1

PIR Motion Sensor x 1

Remote Control x 1

Batteries Included

1. Detection Window

2. Status Indicator

3. Test Button

4. Bracket Slot

5. Self-adhesive pad

fixing markers

Flashes every 2 seconds: Self-testing state

Flashing twice: Self testing finished, enters working mode

Flashes once: Movement is detected

Flashes once every 3 seconds: Low battery indication (immediate battery change required).

1.1. Get to know your product

KIT CONTENTS

1. PIR MOTION

DETECTOR

1.2. LED Indication

Page 3

To test in Working Mode, walk in front of the sensor, the LED should flash once when

movement is detected.

If the sensor is triggered twice in 3 minutes it will enter into power saving (sleep mode).

If no movement is detected within the next 3 minutes, the sensor will return to normal

working mode.

Remove the activation strip. Fit the retaining

screw supplied.

Self-testing will commence for 1 minute as

indicated by the LED flashing every 2 seconds.

To enter Test Mode press the test button at the

back of the PIR. The LEDs will then flash once

when movement is detected, for up to 3 minutes.

Infrared Sensor: Detects movement and

triggers an alarm signal when the system

is armed.

Tamper Switch: If the casing is opened

when in ‘working state’, the tamper

switch will be triggered and generate an

alarm signal.

1.3. PCB Layout

1.5. Working Mode

1.4. Test Mode

AA 1.5V LR6

Infrared

Sensor

Zone

Setting

Tamper

Switch

Test

Button

Status

Indicator

AA 1.5V LR6

Avoid mounting the sensor in areas where draughts may be present or where the

temperature may fluctuate greatly, such as near to windows, air conditioning, heating,

refrigeration units, cooking appliances and direct sunlight.

1.6. Installation

Page 4

2.1. Get to know your product

2. MAGNETIC DOOR/

WINDOW SENSOR

Fit the sensor in a position that will cover your desired protection area:

Fix the bracket to the wall with the fixings kit supplied. For optimum

performance set the height of the bracket to 2 metres above ground

level.

Adjust angle of the PIR sensor to cover the required detection area.

To perform a walk test.

Press the test button

once and walk from let

to right in the room.

The LED indicator will

flash once when motion

is detected.

Status Indicator

Magnet

Transmitter

Suitable for fitting to doors,

windows and any object that

opens and closes.

The Window/door sensor transmits

a signal to the control panel/siren

when ‘contact’ is broken between

the transmitter and the magnet.

Transmits a low battery signal to

the ERA alarm control panel.

Where possible, mount the sensor in the corner of the room so that the logical path

of an intruder would cut across the fan detection pattern. A PIR responds more

effectively to movement across the device that to movement directly towards it.

Page 5

Flashes once: Door/window opened,

transmitter sends the signal to the

control panel/ siren.

Flashes every 3 seconds: Low battery

indication (immediate battery change

recommended)

2.2. LED Indication PCB Layout

Carefully remove the activation strip

from the battery compartment.

Remove the backing paper from one side

of each self-adhesive double-sided strip.

Fix one strip to the back of the magnet

and one to the back of the transmitter.

Peel off the other side of each adhesive

strip. Mount the magnet on the door and

the transmitter on the door frame, with

less than a 1cm separation between the

two.

When opening the door a small red indicator

lights up briefly, this indicates that the

transmitter has sent a signal to the control

panel.

2.3. Installation

Tamper Switch

Battery

Zone Setting

Note: Please refer to the full system instructions for pairing a magnetic sensor.

Do not use the button on the back of the sensor to pair the sensor to the alarm as this

will put the sensor into 24hour mode.

Page 6

3.1. Get to know your product

3.2. Buttons/Functions

3. REMOTE

CONTROL

LED Indication

Arm

Part Arm

(Home Arm)

SOS Panic

Disarm

Flashes Once: Transmits the signal

Low Light Level: Low battery

indication, change the battery.

The remote control enables you to quickly and

conveniently arm and disarm your alarm system.

In the event of an emergency (when in or near

your property), pressing the SOS button will

trigger the an alarm on the control panel/siren.

Arm

Disarm

Part Arm

(Home Arm)

Panic Alarm

Mute Arm

Mute Disarm

Press to arm the control panel/siren and all of the accessories

(Full Arm)

Press to disarm the system

Press to part arm the alarm system (for systems with control

panels only)

Press to activate the panic alarm (SOS).

Press to arm the system with the solar siren in muted/silent

mode.

Press to disarm the system with the solar siren in mute/silent

mode.

Note:

1. For Mute Arm & Mute Disarm operation; press the home button for 1-2 seconds, then press the

Arm or Disarm button for a further 1-2 seconds.

2. The Mute Arm/Disarm will only be performed once before returning to sound. So the Mute

Arm/Disarm process would have to be done each time it is required.

3. By default arm/disarm is with sound. Page 7

Siren Duration Setting

Volume Setting Power On/Off

Inner Tamper Switch

Learn Button

Status LED Indicator

Alarm LED Indicators

Rear Cover

Tamper Socket

Start-up

Battery

Rechargeable 3.7V

1800mAh Lithium Battery

4. SOLAR CHARGED

SIREN

4.1. Positioning

4.2. PCB Layout

4.3. Jumper Setup

Install the Siren to the outside of the building in a position that is clearly visible and at a

height which is relatively inaccessible to an intruder.

The Siren is designed to work on any aspect wall, however for optimum performance try

to avoid installing on a north facing wall or to a wall with shadows cast by other buildings,

trees and roof overhangs.

For optimum radio signal reception mount the Solar Siren to Maximum distance of one

metre from any external or internal metalwork (drainpipes, gutters, radiators, etc).

Rear

Anti-tamper

Switch

Sirens

(Default)

High

Mute

Low

High

Mute

Low

5Min

2Min

30s

5Min

2Min

30s

High

Mute

Low

5Min

2Min

30s

Siren Duration

Setting

Volume

Setting (Default)

Page 8

Tabla de contenidos

Otros manuales de Sistema de seguridad de ERA

ERA

ERA Invincible Manual de usuario

ERA

ERA Protect Replica Siren Manual de usuario

ERA

ERA miGuard A105 Manual de usuario

ERA

ERA E2 Manual de usuario

ERA

ERA WIRELESS HD CCTV SYSTEM Manual de usuario

ERA

ERA SL2KITA Manual de usuario

ERA

ERA Protect SALAPWHESSU Manual de usuario

ERA

ERA SOS100 Manual de usuario

ERA

ERA SL2KIT Manual de usuario

ERA

ERA ADDMORE WS280 Manual de usuario

ERA

ERA HomeGuard Manual de usuario

ERA

ERA Nu Mail Shield TS008 Manual de usuario

ERA

ERA Protect Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario