Epson PowerLite ELPMBUNI Manual de usuario
INSTALLATION MANUAL
ELPMBUNI
EPSON AMERICA, INC.
INDIANAPOLIS DISTRIBUTION CENTER
2350 Stafford Road Suite 101
Plainfield, IN 46168
IN-ELPMBUNI.R3
ELPMBUNI
Installation Instructions Page - 3 -
Table of Contents
Warranty............................................................................................................................................................................................... - 3 -
Contact Premier Mounts....................................................................................................................................................................... - 3 -
Warning Statements.............................................................................................................................................................................. - 4 -
Parts List............................................................................................................................................................................................... - 5 -
Installation Tools .................................................................................................................................................................................. - 5 -
ELPMBUNI Universal Mount Assembly............................................................................................................................................. - 6 -
Projector Preparation ............................................................................................................................................................................ - 7 -
Securing the Bracket to the Projector ................................................................................................................................................... - 9 -
Leveling the Mounting bracket........................................................................................................................................................... - 14 -
Securing the Upper Assembly Ceiling Plate....................................................................................................................................... - 15 -
Low-Profile Installation...................................................................................................................................................................... - 16 -
Securing the Projector to the Upper Assembly................................................................................................................................... - 18 -
Final Adjustments............................................................................................................................................................................... - 19 -
Installing the Plastic Caps................................................................................................................................................................... - 20 -
Warranty
Limited Lifetime Warranty
All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and
workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters,
display equipment or personal injury.
DISCLAIMER OF WARRANTY
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Contact Premier Mounts
In the event of missing and/or damage equipment, or technical questions, the following information can help in
the completion of the installation.
Customer Service – (800) 368-9700
ELPMBUNI
Page - 4 - Installation Manual
Warning Statements
WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE
USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN
THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY
UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT
RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR
CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF
OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR
MODIFICATIONS.
WARNING: THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING A MAX
WEIGHT OF 25 LBS., THE WEIGHT OF THE PROJECTOR. IF NOT, THE CEILING
MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY QUALIFIED
PERSONNEL AS OUTLINED IN THE INSTALLATIONS INSTRUCTIONS MUST BE
ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL
INJURY.
WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS
FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL
INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION
INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
Indicates that the power plug is to be
disconnected from the power outlet.
Contact Premier Mounts with any
questions – (800) 368-9700.
Safety precautions must be taken at all times.
Warning and Caution statements.
A secure structure must support the weight, or load, of the projector. When mounting to a ceiling that contains wooden
studs, dead center of the wooden stud must be confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in
damage to the projector and/or damage to the mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to
do so may result in damage to the projector and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or
mishandling the projector.
Recommended mounting surfaces: wooden studs, solid-flat concrete, and reinforced metal studs. If the mount is to be
installed on any surface other than wooden studs, use suitable hardware (which is commercially available).
ELPMBUNI
Installation Manual Page - 5 -
Parts List
NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of
these parts are missing and/or damaged before beginning installation. If there are parts missing
and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700).
Upper Assembly
(Qty 1)
Mounting Bracket
(Qty 1)
Plastic Barrel Caps
(Qty 4)
M3 Flat Washers
(Qty 4)
Note: Must be used
with the M3 x 16
Phillips screws.
Lag Screws
(#14 x 2”)
(Qty 3)
M4 x 12 Security
Head Screws
(Qty 4)
M3 x 16mm
Phillips Head
Screws (Qty 4)
NOTE: The following hardware is included in the hardware
pack but is not required for the installation.
M5 x 12mm Security Head Screws (Qty 4)
M6 x 12mm Security Head Screws (Qty 4)
Installation Tools
Phillips Head Screw Driver Portable Drill
Soft Material/ Blanket Pencil
Allen Wrench (Supplied) Level (Supplied)
Tape Measure Stud Finder (Commercially Available)
Ladder M5 Allen Wrench
NOTE: Mounting screws will vary by projector. Please see the following pages for model specific hardware:
Pages 10, 11, 12, and 13.
ELPMBUNI
Page - 6 - Installation Manual
ELPMBUNI Universal Mount Assembly
A Single Wooden Stud
Mounting Points
B Solid Structure Mounting
Points
C Ceiling Plate
D Allen Wrench
E Height Adjustment Screws
F Tension Knobs
G Safety Knob
H Security Screws
I Leveling Barrels
J Universal Mounting Bracket
K Leg Assembly
L Projector (Not Supplied)
M Tri-Lock Opening
Option 1
Option 2
Combination
Leg
Single Leg
NOTE: See the best
configuration for your
projector for filter and lamp
access.
NOTE: The four (2-piece) leg
assemblies can be used as
single leg or any combination
of single and dual legs
together as shown in Options
1 and 2. The number of legs
may vary depending on the
number of mounting points
found on the bottom of your
projector.
F
E
L
H
K
B
G
D
A
J
C
I
M
D
J
M
L
ELPMBUNI
Installation Manual Page - 7 -
Projector Preparation
WARNING: Proper installation procedure by qualified personnel as outlined in the installation instructions
must be adhered to. Failure to do so could result in serious personal injury and possible damage
to the projector.
CAUTION: THE PROJECTOR IS FRAGILE; HANDLE WITH CARE AT ALL TIMES.
NOTE: Review the projectors manufacture’s operation manual and refer to the ceiling installation
instruction. Here you will normally find important reference information regarding installation
dimensions such as (distance from the screen to the lens of the projector, top of the lens placement to
the top screen etc. Adherence to these recommendations during your installation will enhance the
quality of your final image on the screen.
1. Carefully invert the projector and place it on a smooth flat surface.
2. Identify the number of mounting points and screw thread (pitch) size.
3. Most projectors have either three or four mounting points and are M4 in thread size (Figure 1).
Figure 1
Inverted
Projector
Flat
surface
Mounting
Points
Blanket, soft
cloth etc
ELPMBUNI
Page - 8 - Installation Manual
4. Separate the upper assembly from the projector mounting bracket by slightly loosening the two tension
knurl knobs to create free play between the bracket tri-lock assembly and the upper section tri-lock
assembly points.
5. Next loosen the safety screw knurl knob far enough to allow the two parts to be rotated 180° apart and
separate.
Figure 2 Figure 3
Figure 4
Tension
Knobs
Upper
Assembly
Safety Knob
Tri-Lock
Opening
Rotate 180°
To Unlock
ELPMBUNI
Installation Manual Page - 9 -
Securing the Bracket to the Projector
NOTE:The two-piece mounting legs are designed to allow routing of the legs around critical ventilation
screens on the base of the projector as shown. You may also reduce the two-piece leg to a one-piece
leg as shown for a better overall fit to the projector.
1. Locate the mounting points on the bottom of the projector and use the appropriate number of mounting
legs.
2. Select the mounting hardware that your projector requires and loosely install the universal mount to your
projector.
NOTE: If your projector requires M3 mounting hardware. Use the M3 x 16 Phillips screws with the M3
flat washers (supplied). Insert the M3 x 16 Phillips screws with the flat washers attached through
the leveling barrel. Using a Phillips screwdriver, loosely secure the screws to the projector
(Figure A).
NOTE: The levelers and leg assembly screws must be loose in order to adjust the height of the mounting
bracket.
Figure 5
FIGURE A
FIGURE
7
One-Piece
Leg
FIGURE
6
Two-Piece
Leg
Leveling
Barrels
Mounting
Hardware
Allen
Wrench
Inverted
Projector
Line u
p
the levelin
g
barrels to the mountin
g
p
oints.
ELPMBUNI
Page - 10 - Installation Manual
NOTE: If your projector model is not shown, when arranging the leg combination, simply ensure access to
filters and lamp housings when aligning brackets. This mount works with all sub-25 pound
projectors.
PowerLite S3, S4, 62C, 76C, 82C,
Hardware: M4 x 12mm (Qty 3)
PowerLite 830p, 835p
Hardware: M4 x 12mm (Qty 4)
ELPMBUNI
Installation Manual Page - 11 -
PowerLite 732c, 737c, 740C, 745C, 750c, 755c, 760c, 765c
Hardware: M4 x 12mm (Qty 3)
To
p
View
Front View
Este manual sirve para los siguientes modelos
36
Tabla de contenidos
Otros manuales de Rack y soporte de Epson
Epson
Epson ELPMB29 Manual de usuario
Epson
Epson ELPMB22 Manual de usuario
Epson
Epson OT-WH30 Manual de usuario
Epson
Epson ELPMB68 Manual de usuario
Epson
Epson ELPMB61 Manual de usuario
Epson
Epson ELPMB26 Manual de usuario
Epson
Epson EPL-5800 Manual de usuario
Epson
Epson ELPMB30 Manual de usuario
Epson
Epson InterakTABLE Instrucciones de funcionamiento y seguridad
Epson
Epson ELPMB47 Manual de usuario
