Epson ELPMB47 Manual de usuario
3
19
35
51
67
83
99
115
129
ELPMB26
19
Included Items List ..................................................................................................... 20
Safety Instructions ......................................................................................................21
Precautions on Where to Mount the Projector ................................................ 23
Installation ..................................................................................................................... 24
Removing the Ceiling Plate from the Projector Plate ............................................ 24
Installing the Ceiling Plate to the Ceiling ...................................................................... 25
Mounting to a Concrete Ceiling ......................................................................................... 26
Fitting the Projector Plate to the Projector .................................................................. 27
Fitting the Projector Plate to the Ceiling Plate ........................................................... 28
Adjusting the Installation Position .......................................................................29
Moving the Projected Images Higher or Lower ........................................................ 29
Tilting the Projected Images to the Right or Left ..................................................... 30
Adjusting the Size of the Projected Images................................................................. 30
Installing the Safety Wires ....................................................................................... 31
Inquiries .......................................................................................................................... 33
Specifications ............................................................................................................... 33
Contents
20
Check the following list to confirm that you have all of the supplied items. If by any chance there is
anything missing or damaged, please contact your dealer.
Included Items List
YProjector mounting screws:
4 pcs. (M6 x 16)
YHexagon wrench (M6) YHexagon wrench (M8)
YSafety wires:
2 pcs. (1.5 m, φ 1.5 mm)
YWire clips: 2 pcs. YUser's Guide (this guide)
YCeiling plate YProjector plate
The ceiling plate and projector plate are preassembled. Separate
them before starting the installation.
3
19
35
51
67
83
99
115
129
21
Read this document carefully to assemble and install this product safely and correctly. Be sure to
follow the safety precautions. Keep these instructions close to hand to help solve any points you
do not understand.
So that you can use the product safely and correctly, symbols are applied in this guide and on
the product to indicate possible harm to the user or to others and the risk of damage to
property. The indications and their meaning are as follows. Make sure you understand them
properly before reading this guide.
Carefully read the warnings in "Safety Instructions / Support and Service Guide" supplied with
your projector before starting the installation to determine a suitable place to install it.
Safety Instructions
Warning This symbol indicates information that, if ignored, could possibly
result in death or personal injury due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Warning
vThe installation work should be performed only by specialists with the required technical
know-how and ability.
Incomplete assembly or installation could cause the projector and ceiling mount to fall and cause
injury.
vThis product weighs approximately 11 kg. When transporting or moving the product,
handle it with care to avoid injury.
vDo not install the ceiling mount on an inclined or weak surface.
The ceiling must be strong enough to install the projector and ceiling mount. Before starting the
installation, carefully check the weight of the projector and the ceiling mount. Make sure the
ceiling is strong enough and use the most appropriate methods to prevent the projector from
falling.
vDo not install the product in a location where it might be exposed to vibration or shock.
Otherwise the product or the installation surface could be damaged. If the product falls, it could
result in death or personal injury.
22
vAlways follow the instructions below when installing the ceiling mount. If installation work
is not carried out correctly, the projector and ceiling mount could fall and cause injury.
• Check the structure and materials of the mounting location and use the most appropriate
construction method.
• Do not hang or mount anything except the specified projector from or on the ceiling mount.
The projectors that can be mounted on this ceiling mount are listed in the catalogs.
• Do not hang from the ceiling mount or apply excessive force to it during or after installation.
• Tighten the screws firmly. Also, never loosen or remove any screws carelessly when mounting
or removing the ceiling mount.
• Never disassemble or remodel the ceiling mount unless indicated in this manual.
vInstall the supplied safety wire to prevent the projector from falling.
The safety wire also prevents the projector from swaying during an earthquake or vibration.
sp.31
vApplying a screw-locking adhesive, lubricant, oil or other substance to the points at which
the projector is fixed to the ceiling mount can make the case crack and the projector fall,
leading to damage or injury. Do not use any sort of adhesive, lubricant or oil when
installing or adjusting the ceiling mount.
vNever loosen any bolts, screws, or nuts after installation. Also, check periodically that no
screws have come loose. If you find a loose screw, tighten it firmly.
vDo not use the ceiling mount and refer all repairs to qualified service personnel under the
following conditions:
• The ceiling mount fell off or was broken before installation.
• The supplied parts have problems and do not work correctly.
vUnplug the projector before installing.
vHandle the power cord carefully.
Incorrect handling could cause fire or electric shock. Observe the following precautions when
handling:
• Do not handle the cord with wet hands.
• Do not use a cord that is damaged or modified.
vDo not install or use the projector in locations where it could be splashed with water such
as outdoors, in a bathroom or shower room, and do not install in locations subject to high
levels of humidity.
This could cause fire or electric shock.
vWhen cleaning, do not use a wet cloth or alcohol, benzine, thinner, and so on.
If water enters the projector, the casing may degrade and break which could cause an electric
shock.
vDo not strongly pull or pinch the projector's power cord during installation. Be careful
especially when passing the power code through the pole.
If the power cord is damaged, it could cause fire or an electric shock. Contact your dealer if the
wires of the power cord become exposed or broken.
Warning
23
Carefully read the warnings in "Safety Instructions / Support and Service Guide" supplied with
your projector before starting the installation to determine a suitable place to install it. In
particular, pay attention to the following items.
vSet the projector up in a location where direct sunlight or strong light from fluorescent lamps
does not shine onto the receiver for the remote control. Strong light shining onto the receiver
for the remote control may interfere with remote control operations.
vInstall the projector so it is away from the air outlet of air conditioners or other similar devices. If
air from an air conditioner blows directly onto the projector, the surrounding temperature
increases and the projector may not operate correctly.
vMake sure there is a big enough gap between the projector and the wall. See the User's Guide
supplied with your projector for details on the necessary distance. If the projector is too close to
the wall, the surrounding temperature increases and the projector may not operate correctly.
vTo limit the effect of external noise, we recommend that you position the projector so that the
cable connecting it to a computer or other devices is no longer than 20 meters.
vThe projector should be installed in a location that is free from dust and moisture to prevent the
lens and internal optical parts from becoming dirty.
vDo not install the projector in a location beyond its operating temperature range. Doing so can
cause it to malfunction.
vClosing the curtains in a bright room makes the projected image easier to see.
Caution
At least two people are needed for the installation. Make sure to provide a sturdy
scaffold for this work.
Otherwise, you may fall or drop the projector and cause injury.
Precautions on Where to Mount the
Projector
24
Removing the Ceiling Plate from the Projector Plate
The ceiling plate is fitted to the projector plate at the factory. Use the following procedure to
separate them.
ARemove the screws for the vertical tilt
adjustment points on both sides using the
supplied M8 hexagon wrench.
BRemove the ceiling plate from the projector
plate.
Installation
Procedure
25
Installing the Ceiling Plate to the Ceiling
Determine the distance to the screen and locate the mounting position before mounting the
ceiling plate.
The distance varies according to the type of the lens unit installed on the projector. See the
"User's Guide" supplied with the projector.
Refer to the ceiling template below to cut the bolt-mounting holes into the ceiling.
When installing this product after uninstalling the ELPMB22, you can use the mounting holes that
are already in the ceiling as they are.
After installing, you cannot rotate the projector beyond ±5° to the left or right. Check that the
projector is facing in the correct direction before installing.
Procedure
Note
Ceiling template (units: mm)
Turn the side of this
cutout to the screen.
The center of
rotation when
adjusting
horizontally
Holes for horizontal rotation
adjustment
The direction of the projector
can be adjusted at up to ±5
degrees by rotating it.
When installing this
product after
uninstalling the
ELPMB22, use these
holes.
26
Mounting to a Concrete Ceiling
When installing the ceiling mount on a concrete ceiling, use 4 anchor bolts (M12). You need to
purchase commercially available anchor bolts.
Before installing the ceiling plate, check that the projector is facing in the correct direction.
The ceiling plate can be horizontally rotated at ±5 degree. Adjust the direction of the projector
using four bolts secured loosely. After adjusting the direction, tighten the hexagon nuts securely.
Caution
vMake sure in advance that the concrete on which this product is installed can hold the
weight and lateral movement of the projector and ceiling mount. If the concrete is not
strong enough or has deteriorated, fortify it with reinforcing bars or something similar.
vInstall the anchor bolts according to the specifications and methods of the
manufacturer of the materials so they do not come out, become loose, or shift.
vTighten the screws firmly during installation or after adjusting the angles.
After tightening the screws, retighten them firmly and make sure that they are not loose.
vEpson accepts no responsibility for any damage or injury caused by lack of wall
strength or inadequate installation.
Warning
Female type anchors
Concrete
Hanger bolts
Flat washers
Hexagon nut
At least 3 threads
Ceiling
Spring
washers
Hexagon nut
The center of rotation when
adjusting the direction
27
Fitting the Projector Plate to the Projector
AAttach the projector so that the on the
projector plate is on the same side as the
projector's lens.
Align the screw holes for the ceiling mount fixing
points with the holes for the projector plate. See
the "User's Guide" supplied with the projector for
details on the position of the projector's ceiling
mount fixing points.
BTighten the supplied four screws (M6 x 16) in
the screw holes of the projector plate using
the supplied M6 hexagonal wrench.
Tighten and secure the three remaining screws.
When attaching the projector plate to the projector,
make sure you use the screws supplied.
Procedure
Caution
vTighten the screws firmly.
After tightening the screws, retighten them firmly and make sure that they are not loose.
vInstall the supplied safety wire to prevent the projector from falling. sp.31
vApplying a screw-locking adhesive, lubricant, oil or other substance to the points at
which the projector is fixed to the ceiling mount can make the case crack and the
projector fall, leading to damage or injury. Do not use any sort of adhesive, lubricant
or oil when installing or adjusting the ceiling mount.
Warning
Otros manuales para ELPMB47
1
Tabla de contenidos
Otros manuales de Rack y soporte de Epson
Epson
Epson EPL-5800 Manual de usuario
Epson
Epson PowerLite ELPMBUNI Manual de usuario
Epson
Epson ELPMB26 Manual de usuario
Epson
Epson OT-WH30 Manual de usuario
Epson
Epson InterakTABLE Instrucciones de funcionamiento y seguridad
Epson
Epson ELPMB29 Manual de usuario
Epson
Epson ELPMB61 Manual de usuario
Epson
Epson ELPMB30 Manual de usuario
Epson
Epson C12C844161 Manual de usuario
Epson
Epson ELPMB68 Manual de usuario
