EPOX BX6 Manual de usuario

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subjected to change without notice.

Manual Revision 1.0

Feb. 16 , 2000

BX6

A PA P

A Pentiumentium

entiumentium

entium®®®®®II/III/CelerII/III/Celer

II/III/CelerII/III/Celer

II/III/Celeronon

onon

Slot1 Processor based AGPSlot1 Processor based AGP

Slot1 Processor based AGP

motherboard

FeaturesBX6

Page 2

FEATURES

BX6 Features:

•BX6 is based on the Pentium®II or Pentium®III Processor operating

at 233 ~ 400MHz (66MHz) or 300 ~ 600MHz (100MHz) on Slot 1.

There are no jumper setting for CPU Speed Setup but detected automati-

cally through the BIOS.

• Designed with Intel’s 82443 BX AGPset.

• Supports up to 768MB of SDRAM (minimum of 8 MB) on board, You can

use 168-pin DIMM x 3. It will automatically detect Extended Data Output

(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM)

at 66MHz or 100MHz.

•BX6 will not support Error Checking and Correcting (ECC) when using

parity DRAM memory modules.

• Supports (1) 16 bit ISA slots, (6) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The BX6 supports (6) PCI

Bus Master slots and a jumperless PCI INT# control scheme which reduces

configuration confusion when plugging in PCI card(s).

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

• Designed with Winbond W83977TF/EF Multi I/O: (1) floppy port, (1)

parallel port (EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported.

• Includes a PS/2 mouse connector.

• Allows use of a PS/2 keyboard.

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com

please visit our Technical Support section for the latest updates).

FeaturesBX6

Page 3

•BX6 utilizes a Lithium battery which provides environmental protec-

tion and longer battery life.

• Supports the Universal Serial Bus (USB) connector. The onboard PIIX4E

chip provides the means for connecting PC peripherals such as; keyboards,

joysticks, telephones, and modems.

• Built-in ATX 20-pin power supply connector.

• Software power-down when using Windows®95/98.

• Supports ring-in feature (remote power-on through external modem,

allow system to be turned on remotely).

• Resume by Alarm - Allow your system to turn on at a preselected time.

•Power Loss Recovery - In the event of a power outage your system will

automatically turn itself back on without user intervention.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports Desktop Management Interface (DMI) facilitating the manage-

ment of desktop computers, hardware and software components and

peripherals, whether they are stand-alone systems or linked into networks.

(optional)

• Supports Hot key, Any key or password Keyboard power ON function

(KBPO).

• Supports USDM software to allow the status monitoring of various aspects

of the system when using Windows®95/98 or Windows®NT 4.0.

• Supports the CPU, PWR and Chassis fan Auto stop in the sleep mode.

• Supports the onboard standby in suspend green or STR mode LED (D2).

• Supports the STR (Suspend To RAM) power management by ACPI’s S3.

•Supports the STR indicator red LED (D8) to avoid plugging or un-plugging

DIMM modules when in a STR mode.

• Supports the System Power LED (PANEL) blinks in the sleep mode.

• Built-in WOL (Wake On Lan) Connector.

InstallationBX6

Page 4

Figure 1

BX6 Detailed Layout

Installation

BX6

Page 5

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure Jumpers

System memory Configuration

Device Connectors

Configure Settings

The following will describe all of the setting that you are required to set before

moving on to step 2.

ROM PCI/ISA BIOS(2A69KPAI)

SENSOR & CPU SPEED SETTING

AWARD SOFTWARE, INC.

Auto Detect DIMM/PCI Clk : Enabled

Spread Spectrum Modulated : Disabled

CPU Host Clock : Default

CPU/PCI Clk Ratio : Auto

CPU/AGP Clk Ratio : Auto

CPU Int Clk Ratio : x3

CPU Clk Frequency : 300(100x3) MHz

CPU:AGP (Clk:Clk) : 3:2 (100:66)

CPU:PCI (Clk:Clk) : 3:1 (100:33)

CPU Vio Voltage : 3.40V

CPU Vcore Voltage : +0.10V

CPU Vcore Voltage : 2.10V

CPU Warning Temperature : 95OC/205OC

Extended JP2 Temperature : 0OC/32OC

Current CPU Temperature : 0OC/32OC

Current System Temperature : 0OC/32OC

Current POWER FAN Speed :4900 RPM

Current CPU FAN Speed :4900 RPM

Current CHASSIS FAN Speed : 4900 RPM

Vcore : 2.10V Vtt(V) : 1.55V

Vio(V) : 3.47V +5V :5.02V

+12V : 12.40V -12V : -11.95V

-5V : -5.50V VBAT (V) : 3.44V

5VSB (V) : 5.08V

Shutdown Temperature : 100OC/167OC

Esc:Quit : Select Item

F1 : Help PU/PD/+/-: Modify

F5 : Old Values (Shift) F2 : Color

F7 : Load Setup Defaults

éé

êê

èè

çç

InstallationBX6

Page 6

Note:Based on the implementation of the Intel 440BX AGPset, the BX6

is able to provide multiple front side bus (FSB) frequencies for Slot 1

processors and memory operations. The motherboard's FSB is easily se-

lected by BIOS Setup listed above to match the FSB required by your

processor. When using the 100MHz FSB (or higher) you must use

PC100 (or better) compliant SDRAM.

Memory is an important component of any motherboard. When

selecting memory for use on the 2themax brand motherboard we

recommend use only the finest quality modules. 2themax would like to

stress that using non-compliant PC100 SDRAM modules with a

100MHz (or higher) FSB severely compromises the integrity of the

system.

epyTUPCkcolClanretxEoitaR

epyT1tolS

IImuitneP

IIImuitneP

noreleC

draCtrevnoC+073S

001

0.2

5.2

0.3

5.3

0.4

5.4

0.5

5.5

0.6

5.6

0.7

5.7

0.8

JP1 = 1-2 - Normal (Default)

= 2-3 - Clear CMOS (momentarily)

JP2 CMOS Clear

JP1 = 1-2 - Normal (Default)

= 2-3 - Clear CMOS (momentarily)

JP1 Chassis (Case) intruder detect

JP4 Keyboard Power-ON function

JP4 = 1-2 - Enabled

= 2-3 - Disabled (Default)

Installation

BX6

Page 7

J7 Reserved for NIC (Network Interface Card) to

Wake the System.

WOL (Wake On Lan) Connector

J1 SB-LINK Connector

Reserved for Creative SB-LINK (Sound

Blaster LINK ) with the Sound Blaster

AWE64D PCI Sound Card to compatible

= 1-2 - Sixth Slave (Default)

= 2-3 - Sixth Master

JPX1&JPX2 The Fifth or Sixth PCI Master Select

JPX1

JPX2

LED1

LED2

Debug card on board

(Please refer to Appendix B for POST codes)

InstallationBX6

Page 8

yromeMlatoT 1MMID )1/0knaB( 2MMID )3/2knaB( 3MMID )5/4knaB(

BM652= mumixaM

*MARDS/ODE ,BM23,BM61,BM8 ,BM821,BM46 1xBM652

enoNenoN

BM215=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

enoN

BM867=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.

*Using non-compliant memory with higher bus speed (over clocking)

may severely compromise the integrity of the system.

System Memory Configuration

Memory Layout

The BX6 supports (3) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized

DRAM).

•We recommend not mixing SDRAM DIMM and EDO DIMM together.

• EDO DIMM can only be used with the 66MHz FSB.

• We recommend using at least 125MHz (-8ns) SDRAM DIMM at the 100MHz

(or higher) FSB as timing becomes more critical at these higher speeds.

• DIMM SDRAM may be 83MHz (-12ns), 100MHz (-10ns) or 125MHz

(-8ns) bus speed.

Figure 2 and Table 1 show several possible memory configurations using

Figure 2

Table 1

DIMM 1 (M1)

DIMM 2 (M2)

DIMM 3 (M3)

Bank 0/1

Bank 2/3

Bank 4/5

-Synchronous

-SDRAM or EDO

DIMM

InstallationBX6

Page 9

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connec-

tions (figure 7).

Figure 7

PS/2 Mouse

PS/2 Keyboard

ParallelPort

COM1USB COM2

J2,J3: Chassis Panel Connector

• Power LED, Speaker, Reset, Turbo LED, HDD LED, IR Conn., Sleep/

Power_ON

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J6: Power Supply Fan Monitoring

• A plug-in for the Power supply so that BIOS can monitor the RPM’s

J8: Chassis Fan Power

• A plug-in for the chassis Fan Power

IDE1: Primary IDE Connector

IDE2: Secondary IDE Connector

FDD1: Floppy Controller Connector

PW1: ATX Power Connector

• 20-pin power connector

Installation

BX6

Page 10

Device Connectors (continued)

(This is connected to the power button on the case. Using the Soft-

Off by Pwr-BTTN feature, you can choose either Instant Off (turns

system off immediately), or 4 sec delay (you need to hold the button

down for 4 seconds before the system turns off). When the system is

in 4 sec delay mode, there is a special feature to make the system to

go into suspend mode when the button is pressed momentarily.)

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard disks

is activate

J3 1

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

Power On/Off

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

KeyLock - Keyboard lock switch & Power LED connector

1. Power LED(+) 4. KeyLock

2. N/C 5. GND

3. GND

Tabla de contenidos

Otros manuales de Placa madre de EPOX

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario