Epever SHI2000 Manual de usuario

SHI Series Pure Sine Wave Inverter

(SHI2000 AND SHI3000)

The information presented in this document does not form

part of any quotation or contract, is believed to be accurate

and reliable and may be changed without notice.

User’s Manual

Before using the inverter, you need to read and save the safety instructions.

CONTENTS

1. Introduction.................................................1

2. Important Safety Instructions ...................2

3. Inverter Operation......................................4

4. Functions....................................................5

5. Troubleshooting.......................................12

6. Maintenance and Warranty....................14

7. Technical Specification............................15

1. Introduction

Thanks for purchasing SHI series inverters. The product is a pure

sine wave inverter which can convert 24/48Vdc to 220/230Vac

50/60Hz based on full digital and intelligent design. It features high

reliability, high efficiency, concise outline, small volume, full

protection functions, easy installation and operation. The inverter

can be applied in many fields, such as household appliances,

electric tools and industrial devices etc, especially for solar

photovoltaic power system.

Features:

Complete isolation-type inverter technology.

Adoption of advanced SPWM technology, pure sine wave

output.

Dynamic current loop control technology to ensure inverter

reliable operation.

Wide DC input voltage range.

Low output harmonic distortion (THD≤3%).

LED indicators for input voltage range, load power range,

normal output & failure state.

Optional energy saving mode.

The output voltage and frequency can be switched.

Extensive protections: short-circuit, overload, under/over input

voltage, over-temperature, and inverter‟s inner fault

identification protections.

Wide working temperature range (industrial level).

Continuous operation at full power.

2. Important Safety Instructions

As an AC power supply equipment, the inverter‟s output voltage is

with the same level as that of household power plug. Mind the AC

output terminals, or you may get an electric shock and result in life

danger!

Attentions:

Connect the DC input according to the requirement strictly. The

power inverter has a relatively wide input range, but too high or

too low input may cause problems even destroy the inverter.

The surge input voltage can‟t exceed 40V for 24V inverters,

80V for 48V inverters, or the inverters will be damaged.

A reverse polarity connection will blow the fuses in the inverter

and may damage the unit.

Do not expose the inverter to humid, flammable, explosive or

dust environment.

Keep the inverter out of children touch.

Inverter input is recommended to connect to battery, the min.

capacity of battery(expressed inAH) should be calculated in the

following way: 5times of the rated power of the inverter/battery

voltage. If for testing purpose, user should select DC power

supply current at least twice greater than that of the inverter

rated input to keep inverter normal operation. Use DC power

supply for testing may cause the damage of the inverter.

When the inverter works continuously, its surface may became

very hot, please make sure the air ventilation clearance around

the inverter is more than 10cm. Keep away from the material or

device which may suffer from high temperature when the

inverter is working. Do not install the inverter in airproof location

and keep enough space around the inverter.

The protective grounding must be connected to the ground. The

cross section of wire should not be less than 4mm2.

A fuse or breaker should be used between battery and inverter,

the value of fuse or switch should be twice of the inverter rated

input current.

The wire connects between battery and inverter should be

shorter than 3m, the current density should be less than

3.5A/mm2while the output of inverter is fully loaded. If the wire

longer than 3m, the current density should be reduced.

Do not connect the battery charger or similar devices to the

input terminal of the inverter.

Do not put the inverter close to the flooded lead-acid battery

because the sparkle in the terminals may ignite the hydrogen

released by the battery.

It‟s an off-grid inverter, do not connect the AC output terminals

to the grid or electrical source, otherwise the inverter may be

damaged.

This inverter can only be used singly, parallel connection or in

series will damage the inverters.

Risk of electric risk, don‟t touch output port when the inverter is

working. The output is forbidden to connect other power,

otherwise the inverter will be damaged. The inverter must be in

off, when connecting load.

Do not attempt to repair the fault inverter yourself, otherwise it

may lead to a serious accident. Please contact the manufacture‟

s engineer.

3. Inverter Operation

Connect the input and output terminals accurately. Turn on the

power using the ON / OFF switch on the front panel. In order to

avoid the protections resulted from the surge power, please turn on

AC loads one by one after the output of the inverter is normal.

Please check it as below:

Set the power switch to the „OFF‟position. Insert the load‟s plug

into the inverter‟s output outlet.

Connect the protective grounding to the ground.

Make sure the fuse or breaker use between battery and inverter

is off.

Connect the battery („+‟ terminal with red line, „-‟with black line).

Do not connect them by contraries, or the power inverter will be

damaged.

Switch on the fuse or breaker. Switch the inverter to ON and then

turn on the loads one by one. Check the operation state of both

power inverter and loads. „Green‟ of the failure LED indicator

means the state is normal.

If there are different loads, it is suggested that turn on the load

with large startup current first, such as television, then turn on the

load such as lamp when the inverter works stable.

If the failure LED indicator is „Red‟ and the buzzer alarms or no

output when you turn on devices, switch off the loads and

power inverter immediately. Check the system by referring to the

troubleshooting guide. Turn on the devices again according to

the operation methods after the failure is removed.

4. Functions

DC Input Panel

AC Output Panel

Protective

Grounding

Fan

Ventilation

DC Input

Terminal

Negative

DC Input

Terminal

Positive

Fault

Indicator

AC Outlet②

ON/OFF Switch

Switch Node

RS485 Port

Input Level Indicator

Load Level

Indicator

Mode Switch

AC Outlet①

Note：1.When the load current is less than 10A, use "AC outlet ①"

or “AC outlet ②"; If the load current is greater than 10A, must use

“AC outlet ②".

2.The cross section of wire should not be more than 4mm2, and it

is recommended to use stranded wire, when using "AC outlet ②".

3.Stop inverter working firstly, insert a sharp tool to the " AC outlet

②" at the top of the holes and then remove the wire.

The Optional Outlet

Australia/New Zealand

European

Input Level: Display Input Voltages

LED Status

24V

48V

RED Slow Blink

＜21

＜42

RED

21～22

42～44

ORANGE

22～24

44～48

GREEN

24～29

48～58

ORANGE Fast Blink

29～32

58～64

RED Fast Blink

＞32

＞64

Load Level: Display AC Loads

LED Status

AC Load

ORANGE

＜20%

GREEN

20%～75%

RED

＞75%

RED Slow Blink

Overload

RED Fast Blink

Short Circuit

Output & Fault Status

LED Status

Status

GREEN

Output Normal

RED Fast Blink

Overload or Short circuit, No Output

RED Slow Blink

Over or Low input voltage, No Output

ORANGE Fast Blink

Over temperature, No Output

ORANGE OR RED

Inverter Fault, No Output

OFF

Saving mode, Power Off，No Output

Alarms

Alarms

Status

Buzzer

Sounds

Overload or Short circuit, No Output

Over or Low input voltage, No Output

Over temperature, No Output

Inverter Fault, No Output

The buzzer stops after 20S.

Protections

Overload or Output Short Circuit Protection

Overload

Character

125%

150%

200%

230%

＞250%

Continuance

60S

10S

＜0.2S

＜

0.01S

Recover 3

times

Space 5 seconds for the first time, 10 seconds

for the second time, and 15 seconds for the

third time

If the overload or short circuit status still remains when the inverter

tries to recover for 3 times, you should reduce or clear the loads

and then restart the inverter manually. Load over than 250% will be

treated as output short circuit.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de Epever

Epever

Epever IP1000-Plus Manual de usuario

Epever

Epever IPT Series Manual de usuario

Epever

Epever UPower Series Manual de usuario

Epever

Epever IP350-12 Manual de usuario

Epever

Epever IPower Series Manual de usuario

Epever

Epever IPower-Plus Series Manual de usuario

Epever

Epever LD150S-N1 Manual de usuario

Epever

Epever IP1500-11 Manual de usuario

Epever

Epever UP2000-HM6022 Manual de usuario

Epever

Epever NPower Series Manual de usuario

Epever

Epever NP260 Manual de usuario

Epever

Epever HP3542-AH0650P20SA Manual de usuario

Epever

Epever VS1024AU Manual de usuario

Epever

Epever Sunshine Solar IP350-Plus Manual de usuario

Epever

Epever UP2000-HM6021 Manual de usuario

Epever

Epever NPower Series Manual de usuario

Epever

Epever Tracer 2210CN Manual de usuario

Epever

Epever UP1000 Manual de usuario

Epever

Epever UP1500-M3222 Manual de usuario

Epever

Epever IP1500-Plus Series Manual de usuario

Epever

Epever Tracer AN Series Manual de usuario

Epever

Epever IP350-11 Manual de usuario

Epever

Epever TP10K Manual de usuario

Epever

Epever LS EPD Series Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario