Epever IP350-12 Manual de usuario

IPower Series

——Pure Sine Wave Inverter

User Manual

Models:

IP350-12/22/11/21

IP500-12/22/11/21

IP1000-12/22/11/21

IP1500-12/22/11/21

IP2000-22/42/21/41

CONTENTS

1. Important Safety Instructions ...................1

2. Introduction.................................................3

3. Designations of models ............................4

4. Wiring..........................................................5

5. Functions....................................................7

6. Protection.................................................. 11

7. Troubleshooting.......................................13

8. Maintenance.............................................14

9. Disclaimer.................................................14

10. Technical Specification .........................15

1. Important Safety Instructions

As an AC power supply equipment, the inverter’s output voltage is

with the same level as that of household power plug. Mind the AC

output terminals, or you may get an electric shock and result in life

danger!

Attentions:

Connect the DC input according to the requirement strictly. The

power inverter has a relatively wide input range, but too high or

too low input may cause problems even destroy the inverter.

A reverse polarity connection will blow the fuses in the inverter

and may damage the unit.

Do not expose the inverter to humid, flammable, explosive or

dust environment.

Keep the inverter out of children touch.

Inverter input is recommended to connect to battery, the min.

capacity of battery(expressed inAH) should be calculated in the

following way: 5times of the rated power of the inverter/battery

voltage. If for testing purpose, user should select DC power

supply current at least twice greater than that of the inverter

rated input to keep inverter normal operation. Use DC power

supply for testing may cause the damage of the inverter.

When the inverter works continuously, its surface may become

very hot, please make sure the air ventilation clearance around

the inverter is more than 10cm. Keep away from the material or

device which may suffer from high temperature when the

inverter is working. Do not install the inverter in airproof location

and keep enough space around the inverter.

The protective grounding must be connected to the ground. The

cross section of wire should not be less than 4mm2.

The wire connects between battery and inverter should be

shorter than 3m, the current density should be less than

3.5A/mm2while the output of inverter is fully loaded. If the wire

longer than 3m, the current density should be reduced.

A fuse or breaker should be used between battery and inverter,

the value of fuse or breaker should be twice of the inverter rated

input current.

Do not connect the battery charger or similar devices to the

input terminal of the inverter.

Do not put the inverter close to the flooded lead-acid battery

because the sparkle in the terminals may ignite the hydrogen

released by the battery.

It’s an off-grid inverter, do not connect the AC output terminals

to the grid or electrical source, otherwise the inverter may be

damaged.

This inverter can only be used singly, parallel connection or in

series will damage the inverters.

Risk of electric shock, don’t touch output port when the inverter

is working. The output is forbidden to connect other power

sources or grid, otherwise the inverter will be damaged. The

inverter must be in off, when connecting load.

Do not attempt to repair the fault inverter by yourself, otherwise it

may lead to a serious accident. Please contact the manufacture’

s engineer.

2. Introduction

IPower series is a kind of pure sine wave inverter which can convert.

12/24/48VDC to 220/230VAC(or 110/120VAC). Industrial design,

compared with the civil design, has a wider operating temperature,

easy installation and operation. The wide input voltage range is

ideal for solar system application. The inverter can be applied in

many fields, such as household emergency lighting system, vehicle

mounted system and small field power supply etc.

Features:

Safe design with input and output electrical isolation

Adoption of advanced SPWM technology, pure sine wave output

Optional output voltage 220/230VAC(or 110/120VAC), choosing

by DIP switch

LED indicators for fault status and working status

Lower No-load consumption

Max. efficiency up to 95%(IP2000-22, IP2000-42)①

Input protection: Over voltage protection, low voltage protection

Output protection: Over load protection, short circuit protection

Over temperature protection: Temperature-controlled Fan

Ventilation; Inverter turns off automatically when overheating

Operational USB output 5VDC/1A

Operational RS485 communication port②

①The efficiency is tested at rated input voltage,220V output with

resistive load, 25℃Ambient temperature,1500W and higher version

②1000W and higher version support RS485 communication port

optional.

3. Designations of models

Model

Input Rated

Voltage

Output Voltage

Output Power

15 min.

IP350-12

12VDC

220/230VAC

350W

IP350-22

24VDC

220/230VAC

350W

IP500-12

12VDC

220/230VAC

500W

IP500-22

24VDC

220/230VAC

500W

IP1000-12

12VDC

220/230VAC

1000W

IP1000-22

24VDC

220/230VAC

1000W

IP1500-12

12VDC

220/230VAC

1500W

IP1500-22

24VDC

220/230VAC

1500W

IP2000-22

24VDC

220/230VAC

2000W

IP2000-42

48VDC

220/230VAC

2000W

IP350-11

12VDC

110/120VAC

350W

IP350-21

24VDC

110/120VAC

350W

IP500-11

12VDC

110/120VAC

500W

IP500-21

24VDC

110/120VAC

500W

IP1000-11

12VDC

110/120VAC

1000W

IP1000-21

24VDC

110/120VAC

1000W

IP1500-11

12VDC

110/120VAC

1500W

IP1500-21

24VDC

110/120VAC

1500W

IP2000-21

24VDC

110/120VAC

2000W

IP2000-41

48VDC

110/120VAC

2000W

220/230VAC output outlet: Universal, Australia/New Zealand, European,

Terminal(IP1000 and above models)

110/120VAC output outlet: Universal, Terminal(IP1000 and above models)

All the IPower models have option for USB output.

All the IPower models have option for RS485 communication except IP350 and

IP500

4. Wiring

(1)12/24/48Vsystem DC input

(2) 220/230V AC(or 110/120V) output

Operation Steps:

Step 1: Turn the power switch of the inverter to OFF

Step 2: Disconnect the input breaker or the fuse between inverter

and battery, connect the battery terminals (‘+’ with red line and ‘-’

with black line). Do not connect the poles by contraries.

Step 3: Use the cable no less than 4mm2to connect the grounding

terminal of the inverter to the ground.

Step 4: Connect the plug of AC load to the inverter AC outlet

Step 5: Switch on the input breaker or the fuse between inverter

and battery; turn on the power switch to start the inverter. If the

green indicator is on solid, turn on the loads one by one. Check the

operation state of the inverter and loads.

Step 6: If there are different types of loads, it is suggested that turn

on the loads with higher startup current first, such as television,

then after the loads works stably, turn on the loads with lower

startup current, such as incandescent lamp.

Step 7: If the Fault indicator is red and the buzzer alarms when turn

on the devices, please switch off the loads and inverter

immediately.

Note: When use USB port for charging, it is suggested

to charge the power bank first, and then use the power

bank to charge mobile phones.

5. Functions

DC Input Panel

AC Output Panel

Otros manuales para IP350-12

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de Epever

Epever

Epever LS-B Series Manual de usuario

Epever

Epever NPower Series Manual de usuario

Epever

Epever LS0512E Manual de usuario

Epever

Epever Sunshine Solar IP350-Plus Manual de usuario

Epever

Epever UPower Series Manual de usuario

Epever

Epever IP1000-Plus Manual de usuario

Epever

Epever SHI2000-22-G Manual de usuario

Epever

Epever Tracer AN Series Manual de usuario

Epever

Epever NP260 Manual de usuario

Epever

Epever IP1500-Plus Series Manual de usuario

Epever

Epever NPower Series Manual de usuario

Epever

Epever TP10K Manual de usuario

Epever

Epever LD150S-N1 Manual de usuario

Epever

Epever LS-EPD Series Manual de usuario

Epever

Epever Tracer1305EPLI Manual de usuario

Epever

Epever UP1500-M3222 Manual de usuario

Epever

Epever IP1500-11 Manual de usuario

Epever

Epever UP2000-HM6021 Manual de usuario

Epever

Epever SHI2000 Manual de usuario

Epever

Epever IP350-11 Manual de usuario

Epever

Epever HP3542-AH0650P20SA Manual de usuario

Epever

Epever UPower Series Manual de usuario

Epever

Epever IPT Series Manual de usuario

Epever

Epever UP2000-HM6022 Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario