Endress+Hauser ITEMP TMT82 Manual de usuario

Operating Instructions

iTEMP® TMT82

Dual-input temperature transmitter

BA01028T/09/EN/14.12

71198558

Valid as of version

01.00 (device version)

iTEMP® TMT82

2 Endress+Hauser

Brief overview

For quick and straightforward commissioning:

Safety instructions (® ä 6)

Installation instructions (® ä 10)

Wiring (® ä 15)

Display and operating elements (® ä 20)

Commissioning (® ä 30)

Commissioning using the HART® communication interface - Quick start for device

configuration for standard operation

Customer-specific configuration (® ä 51)

Complex measurement tasks require the configuration of additional functions, which the

user can select, set and adapt to his/her process conditions by setting the appropriate device

parameters. A detailed description of all functions and device parameters.

iTEMP® TMT82 Table of contents

Endress+Hauser 3

Table of contents

1 Important document information ..... 4

1.1 About this document ..................... 4

1.2 Document conventions .................... 4

2 Basic safety instructions .............. 6

2.1 Requirements for the personnel .............. 6

2.2 Designated use .......................... 6

2.3 Operational safety ........................ 6

3 Identification ....................... 7

3.1 Device designation ....................... 7

3.2 Scope of delivery ........................ 8

3.3 Certificates and approvals .................. 8

4 Installation instructions ............. 10

4.1 Incoming acceptance, transport, storage ........ 10

4.2 Installation conditions .................... 10

4.3 Installation instructions ................... 10

4.4 Post-installation check .................... 14

5 Wiring ............................ 15

5.1 Quick wiring guide ...................... 15

5.2 Connecting the sensor cables ............... 16

5.3 Connecting the power supply and signal cables .. 17

5.4 Shielding and grounding .................. 18

5.5 Post-connection check ................... 19

6 Operating options .................. 20

6.1 Overview of operation options .............. 20

6.2 Structure and function of the operating menu .... 21

6.3 Measured value display and operating elements .. 23

6.4 Access to the operating menu via the operating

tool ................................ 25

7Integrating the transmitter via HART®

protocol ........................... 28

7.1 HART device variables and measured values ..... 28

7.2 Device variables and measured values ......... 29

8 Commissioning .................... 30

8.1 Function check ........................ 30

8.2 Switching on the transmitter ............... 30

8.3 Enabling configuration .................... 30

9 Maintenance ...................... 30

10 Accessories ........................ 30

10.1 Optional accessories ..................... 31

10.2 Communication-specific accessories .......... 31

10.3 System components and data manager ......... 32

11 Diagnostics and troubleshooting ..... 33

11.1 Troubleshooting ........................ 33

11.2 Diagnostics events ...................... 35

11.3 Spare parts ............................ 38

11.4 Return .............................. 38

11.5 Disposal ............................. 38

11.6 Software history and overview of compatibility ... 39

12 Technical data ..................... 40

13 Operating menu and parameter

description ........................ 51

13.1 "Display/operation" menu ................. 57

13.2 "Setup" menu .......................... 61

13.3 "Diagnostics" menu ...................... 72

13.4 "Expert" menu ......................... 80

Index .................................. 96

Important document information iTEMP® TMT82

4 Endress+Hauser

1 Important document information

1.1 About this document

1.1.1 Document function

These Operating Instructions contain all the information that is required in various phases of the

life cycle of the device: from product identification, incoming acceptance and storage, to

mounting, connection, operation and commissioning through to troubleshooting, maintenance

and disposal.

1.1.2 Additional standard documentation on the device

Document Purpose and content of the document

Technical Information

TI01010T/09/en

Planning aid for your device

The document contains all the technical data on the device and provides an

overview of the accessories and other products that can be ordered for the

device.

Brief Operating Instructions

KA01095T/09/en

Guide that takes you quickly to the 1st measured value

The Brief Operating Instructions contain all the essential information from

incoming acceptance to initial commissioning.

The document types listed are available:

•On the CD supplied with the device

•In the Download Area of the Endress+Hauser Internet site: www.endress.com ®

Download

1.1.3 Safety Instructions (XA)

When using in hazardous areas, the national safety requirements must be met. Separate Ex

documentation is contained in these Operating Instructions for measurement systems that are to

mounted in hazardous areas. Strict compliance with the installation instructions, ratings and

safety instructions as listed in this supplementary documentation is mandatory. Ensure you are

using the correct Ex documentation for the relevant Ex-approved device. The number of the

related Ex documentation (XA...) is indicated on the nameplate. You can use this Ex

documentation if the two numbers (i.e. in the Ex documentation and on the nameplate) are

identical.

1.2 Document conventions

1.2.1 Safety symbols

Symbol Meaning

DANGER

A0011189-EN

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result

in serious or fatal injury.

CAUTION

A0011191-EN

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result

in minor or medium injury.

NOTICE

A0011192-EN

NOTE!

This symbol contains information on procedures and other facts which do not result in

personal injury.

iTEMP® TMT82 Important document information

Endress+Hauser 5

1.2.2 Electrical symbols

Symbol Meaning

A0011197

Direct current

A terminal to which DC voltage is applied or through which direct current flows.

A0011198

Alternating current

A terminal to which alternating voltage (sine-wave) is applied or through which alternating current flows.

)

A0011200

Ground connection

A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.

A0011199

Protective ground connection

A terminal which must be connected to ground prior to establishing any other connections.

A0011201

Equipotential connection

A connection that has to be connected to the plant grounding system: This may be a potential

equalization line or a star grounding system depending on national or company codes of practice.

1.2.3 Symbols and notation for certain types of information

Symbol Meaning

A0011182

Allowed

Indicates procedures, processes or actions that are allowed.

A0011183

Preferred

Indicates procedures, processes or actions that are preferred.

A0011184

Forbidden

Indicates procedures, processes or actions that are forbidden.

A0011193

Tip

Indicates additional information.

A0011194

Reference to documentation

Refers to the corresponding device documentation.

A0011195

Reference to page

Refers to the corresponding page number.

A0011196

Reference to graphic

Refers to the corresponding graphic number and page number.

1., 2., 3. Series of steps

ÃResult of a sequence of actions

1.2.4 Symbols and notation in graphics

Symbol Meaning

1,2,3 ... Item numbers

A, B, C, ... Views

A-A, B-B, C-C, ... Sections

A0011187

Hazardous area

Indicates a hazardous area.

A0011188

Safe area (non-hazardous area)

Indicates a non-hazardous area.

Basic safety instructions iTEMP® TMT82

6 Endress+Hauser

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill the

following requirements:

►Trained, qualified specialists must have a relevant qualification for this specific function and

task

►Are authorized by the plant owner/operator

►Are familiar with federal/national regulations

►Before beginning work, the specialist staff must have read and understood the instructions in

the Operating Instructions and supplementary documentation as well as in the certificates

(depending on the application)

►Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

►Being instructed and authorized according to the requirements of the task by the facility's

owner-operator

►Following the instructions in these Operating Instructions

2.2 Designated use

The device is a universal and user-configurable temperature transmitter with either one or two

sensor inputs for a resistance thermometer (RT), thermocouples (TC), resistance and voltage

transmitters. The head transmitter version of the device is intended for mounting in a flat-face

terminal head as per DIN EN 50446. It is also possible to mount the device on a DIN rail using

the optional DIN rail clip. The device is also optionally available in a version suitable for DIN rail

mounting as per IEC 60715 (TH35).

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Operational safety

►Operate the device in proper technical condition and fail-safe condition only.

►The operator is responsible for interference-free operation of the device.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the hazardous area

(e.g. explosion protection or safety equipment):

►Based on the technical data on the nameplate, check whether the ordered device is permitted

for the intended use in the hazardous area. The nameplate can be found on the side of the

transmitter housing.

►Observe the specifications in the separate supplementary documentation that is an integral

part of these Instructions.

Electromagnetic compatibility

The measuring system complies with the general safety requirements in accordance with EN

61010, the EMC requirements of IEC/EN 61326 and NAMUR Recommendation NE 21 and NE

89.

NOTICE

►The unit must only be powered by a power supply that operates using an energy-limited

electric circuit that is compliant with IEC 61010-1, "SELV or Class 2 circuit".

iTEMP® TMT82 Identification

Endress+Hauser 7

3 Identification

3.1 Device designation

The following options are available for identification of the device:

• Nameplate specifications

•Enter the serial number from the nameplate in W@M Device Viewer (www.endress.com/

deviceviewer): All data relating to the device and an overview of the technical documentation

supplied with the device are displayed.

3.1.1 Nameplate

The right device?

Compare and check the data on the nameplate of the device against the requirements of the

measuring point:

123

11-42V 012345678910

xx.yy.zz

TMT82- XXXXX/XX

iTEMP®

Made in Germany 2011

D-87484 Nesselwang

Ser.no.:

FW:

Input:

12345678ABCDEFGH

Current consum.: 23,6 mA Dev.Rev: 1

Ext. ord. cd.:

XXXXXXXXXXXXX#

II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C

II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C

EH 08.001X

Install per XA00102R/09/a3/xx.xx

0044

A0014561

å 1 Nameplate of the head transmitter (example, Ex version)

1 Power supply, current consumption and extended order code

2 Serial number, device revision and firmware version

3 Approvals with symbols

4 2 lines for the TAG name

5 Approval in hazardous area with number of the relevant Ex documentation (XA...)

6 Order code and manufacturer ID

Identification iTEMP® TMT82

8 Endress+Hauser

0044

iTEMP®TMT82

Made in Germany 2012 D-87484 Nesselwang

TAGXXXXXXXXXXX

FW: XX.XX.XX Dev. Rev.: X

Order code: TMT82-xxx/xx

Ext. ord. cd.: XXXXXXXXXXX

Ser. no.: XXXXXXXXX

Input: 12-42 V

Current cunsum.: 23,0 mA

II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C

II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C

EH 08.001X

Install per XA0xxxxT/09/a3/xx.xx

A0017924

å 2 Nameplate of DIN rail transmitter (example, Ex version)

1 Product description and manufacturer ID

2 Order code, extended order code and serial number

3 Power supply and current consumption

4 Approval in hazardous area with number of the relevant Ex documentation (XA...)

5 Firmware version and device version

6 Approval logos

7 2 lines for the TAG name

3.2 Scope of delivery

The scope of delivery of the device comprises:

•Temperature transmitter

• Mounting material (head transmitter)

• Hard copy of multi-language Brief Operating Instructions

• Operating Instructions and additional documentation on CD-ROM

•Additional documentation for devices which are suitable for use in hazardous areas (0 1),

such as Safety Instructions (XA), Control or Installation Drawings (ZD).

3.3 Certificates and approvals

The device left the factory in a safe operating condition. The device complies with the standards

EN 61 010-1 "Protection Measures for Electrical Equipment for Measurement, Control,

Regulation and Laboratory Procedures" and with the EMC requirements of IEC/EN 61326.

3.3.1 CE mark, Declaration of Conformity

The device therefore meets the legal requirements of the EC guidelines. The manufacturer

confirms that the device is compliant with the relevant guidelines by applying the CE mark.

3.3.2 HART® protocol certification

The temperature transmitter is registered by HART® Communication. The device meets the

requirements of the HART Communication Protocol Specifications, April 2001, Revision 6.0.

3.3.3 Registered trademarks

• HART®

Registered trademark of the HART® Communication Foundation

• iTEMP®

Registered trademark of Endress+Hauser Wetzer GmbH + Co. KG, Nesselwang, D

iTEMP® TMT82 Identification

Endress+Hauser 9

An overview of other approvals and certifications is provided in the "Technical data"

section(® ä 50).

Installation instructions iTEMP® TMT82

10 Endress+Hauser

4 Installation instructions

4.1 Incoming acceptance, transport, storage

4.1.1 Incoming acceptance

• Is the packaging or content damaged?

• Is the delivery complete? Compare the scope of delivery against the information on your order

form.

4.1.2 Transport and storage

• Pack the device in such a way as to protect it reliably against impact for storage (and

transportation). The original packaging provides optimum protection.

• Permitted storage temperature:

– Head transmitter: –50 to +100 °C (–58 to +212 °F)

– DIN rail transmitter: –40 to +100 °C (–40 to +212 °F)

4.2 Installation conditions

4.2.1 Dimensions

The dimensions of the device are provided in the "Technical data" section. (® ä 40).

4.2.2 Mounting location

• Head transmitter:

– In the terminal head, flat face, as per DIN EN 50446, direct mounting on insert with cable

entry (middle hole 7 mm)

–In the field housing, separated from the process(® ä 30)

• DIN rail transmitter:

Designed for mounting on DIN rail (IEC 60715 TH35).

It is also possible to mount the device on a DIN rail as per IEC 60715 using the DIN rail clip

accessory (® ä 30).

Information about the conditions (such as the ambient temperature, degree of protection, climate

class etc.) that must be present at the installation point so that the device can be mounted

correctly, is provided in the "Technical data" section(® ä 40).

When using in hazardous areas, the limit values of the certificates and approvals must be

observed (see Ex Safety Instructions).

4.3 Installation instructions

A Phillips head screwdriver is required to mount the head transmitter.

NOTICE

Do not overtighten the mounting screws as this could damage the head transmitter.

►Maximum torque = 1 Nm (¾ pound-feet).

Otros manuales para iTEMP TMT82

Tabla de contenidos

Otros manuales de Transmisor de Endress+Hauser

Endress+Hauser

Endress+Hauser iTEMP TMT82 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Flowmeter Proline 200 Especificaciones técnicas

Endress+Hauser

Endress+Hauser tmt142 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Proline Promass O 100HART Especificaciones técnicas

Endress+Hauser

Endress+Hauser TMD1000 Manual de usuario

Endress+Hauser

Endress+Hauser RMA 422 Manual de usuario

Endress+Hauser

Endress+Hauser RMA42 Especificaciones técnicas

Endress+Hauser

Endress+Hauser RMA42 Manual de usuario

Endress+Hauser

Endress+Hauser smartgrad TMD833 Manual de usuario

Endress+Hauser

Endress+Hauser cerabar S PROFIBUS-PA Manual de usuario

Endress+Hauser

Endress+Hauser Flowmeter Proline 300 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Cerabar S PMP71 Manual de usuario

Endress+Hauser

Endress+Hauser deltabar S PMD 25 K Manual de usuario

Endress+Hauser

Endress+Hauser CM14 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Instrucciones de funcionamiento e instalación

Endress+Hauser

Endress+Hauser iTEMP TMT85 Manual de usuario

Endress+Hauser

Endress+Hauser iTEMP TMT182 Manual de usuario

Endress+Hauser

Endress+Hauser tmt142 Instrucciones de instalación

Endress+Hauser

Endress+Hauser Prosonic S FMU95 Instrucciones de funcionamiento e instalación

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93 Manual de usuario

Endress+Hauser

Endress+Hauser cerabar S Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar PMC71B Manual de usuario

Endress+Hauser

Endress+Hauser Proline 500 digital PROFIBUS DP Especificaciones técnicas

Endress+Hauser

Endress+Hauser Liquisys M CLM223 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Endress+Hauser iTEMP TMT82 Manual de usuario

Manuales populares de Transmisor de otras marcas