Endress+Hauser Micropilot M FMR245 Manual de usuario

BA253F/00/en/05.06

Nr. 52012500

Valid as of software version:

V 01.04.00 (amplifier)

V 1.0 (communication)

Operating Instructions

Micropilot M FMR245

Level-Radar

Brief operating instructions Micropilot M FMR245 with FOUNDATION Fieldbus

2Endress+Hauser

Brief operating instructions

L00-FMR2xxxx-19-00-00-en-039

!Note!

This operating manual explains the installation and initial start-up for the level transmitter. All

functions that are required for a typical measuring task are taken into account here. In addition, the

Micropilot M provides many other functions that are not included in this operating manual, such as

optimising the measuring point and converting the measured values.

An overview of all device functions can be found on Page 98.

The operating manual BA 221F/00/en "Description of the instrument functions for Micropilot M"

provides an extensive description of all device functions, which can be found on the enclosed

CD-ROM.

… …

KA 159F/00/a2/05.02

52006292

… …

Micropilot M - Brief operating instructions

- dome

ceiling

- horizontal

cyl.

- bypass

…

- unknown

- DC: <1.9

- DC: 1.9 … 4

- DC: 4 … 10

- DC: >10

- standard

- calm

surface

- add. agitator

…

input E

(see sketch)

input F

(see sketch)

only for

bypass +

stilling well

- ok

- too small

- too big

- unknown

- manual

displayed

(see sketch)

D and L are confirm

or specify

range

suggestion

000

measured value

Group

selection

basic setup

safety settings

system

parameter

display

envelope curve

linearisation

extended calibr.

output (HART, FF)

profibus param.(PA)

092

language

diagnostics

0A0

present

error

002

tank shape

004

process

cond.

005

empty

calibr.

006

full

calibr.

007

pipe

diameter

008

dist./

meas value

051

check

distance

003

medium

cond.

052

range of

mapping

053

start

mapping

008

dist./

meas value

flange:

reference point

of measurement

- envel. curve

- incl. FAC

- incl. cust. map

- single curve

- cyclic

= 100: unlocked

100: locked≠

= 2457: unlocked

2457: locked≠

0E1

plot settings

0E2

recording

curve

0A1

error

0A4

unlock

parameter

threaded connection:

reference point of

measurement

HART

PA , F F

}

Contrast: +or +

Micropilot M FMR245 with FOUNDATION Fieldbus Table of contents

Endress+Hauser 3

Table of contents

1 Safety instructions . . . . . . . . . . . . . . . . 4

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Installation, commissioning and operation . . . . . . . . 4

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Notes on safety conventions and symbols . . . . . . . . . 5

2 Identification . . . . . . . . . . . . . . . . . . . . 6

2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Certificates and approvals . . . . . . . . . . . . . . . . . . . . 8

2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 8

3 Mounting . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Quick installation guide . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Incoming acceptance, transport, storage . . . . . . . . . 10

3.3 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 11

3.4 Installation instructions . . . . . . . . . . . . . . . . . . . . . 18

3.5 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 23

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 24

4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . . . . 24

4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 27

4.3 Recommended connection . . . . . . . . . . . . . . . . . . 27

4.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 27

4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 27

5 Operation . . . . . . . . . . . . . . . . . . . . . . 28

5.1 Quick operation guide . . . . . . . . . . . . . . . . . . . . . . 28

5.2 Display and operating elements . . . . . . . . . . . . . . . 30

5.3 Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.4 Display and acknowledging error messages . . . . . . 36

5.5 FOUNDATION Fieldbus communication . . . . . . . . 37

6 Commissioning. . . . . . . . . . . . . . . . . . 54

6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6.2 Switching on the measuring device . . . . . . . . . . . . 54

6.3 Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

6.4 Basic Setup with the VU 331 . . . . . . . . . . . . . . . . . 57

6.5 Basic Setup with the ToF Tool . . . . . . . . . . . . . . . . 69

7 Maintenance. . . . . . . . . . . . . . . . . . . . 74

8 Accessories. . . . . . . . . . . . . . . . . . . . . 75

9 Trouble-shooting . . . . . . . . . . . . . . . . 78

9.1 Trouble-shooting instructions . . . . . . . . . . . . . . . . 78

9.2 System error messages . . . . . . . . . . . . . . . . . . . . . . 79

9.3 Application errors . . . . . . . . . . . . . . . . . . . . . . . . . 81

9.4 Orientation of the Micropilot . . . . . . . . . . . . . . . . . 83

9.5 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

9.6 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

9.7 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

9.8 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

9.9 Contact addresses of Endress+Hauser . . . . . . . . . . . 92

10 Technical data . . . . . . . . . . . . . . . . . . . 93

10.1 Additional technical data . . . . . . . . . . . . . . . . . . . . 93

11 Appendix. . . . . . . . . . . . . . . . . . . . . . . 98

11.1 Operating menu Foundation Fieldbus, ToF Tool . . . 98

11.2 Description of functions . . . . . . . . . . . . . . . . . . . . 100

11.3 Function and system design . . . . . . . . . . . . . . . . . 101

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Safety instructions Micropilot M FMR245 with FOUNDATION Fieldbus

4Endress+Hauser

1 Safety instructions

1.1 Designated use

The Micropilot M FMR 245 is a compact radar level transmitter for the continuous, contactless

measurement of liquids, pastes and sludge. The device can also be freely mounted outside closed

metal vessels because of its operating frequency of about 26 GHz and a maximum radiated pulsed

energy of 1mW (average power output 1 µW). Operation is completely harmless to humans and

animals.

1.2 Installation, commissioning and operation

The Micropilot M has been designed to operate safely in accordance with current technical, safety

and EU standards. If installed incorrectly or used for applications for which it is not intended,

however, it is possible that application-related dangers may arise, e.g. product overflow due to

incorrect installation or calibration. For this reason, the instrument must be installed, connected,

operated and maintained according to the instructions in this manual: personnel must be authorised

and suitably qualified. The manual must have been read and understood, and the instructions

followed. Modifications and repairs to the device are permissible only when they are expressly

approved in the manual.

1.3 Operational safety

1.3.1 Hazardous areas

Measuring systems for use in hazardous environments are accompanied by separate "Ex

documentation", which is an integral part of this Operating Manual. Strict compliance with the

installation instructions and ratings as stated in this supplementary documentation is mandatory.

• Ensure that all personnel are suitably qualified.

• Observe the specifications in the certificate as well as national and local standards and regulations.

1.3.2 FCC approval

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

"Caution!

Changes or modifications not expressly approved by the part responsible for

compliance could void the user’s authority to operate the equipment.

Micropilot M FMR245 with FOUNDATION Fieldbus Safety instructions

Endress+Hauser 5

1.4 Notes on safety conventions and symbols

In order to highlight safety-relevant or alternative operating procedures in the manual, the following

conventions have been used, each indicated by a corresponding symbol in the margin.

Safety conventions

#Warning!

A warning highlights actions or procedures which, if not performed correctly, will lead to personal

injury, a safety hazard or destruction of the instrument

"Caution!

Caution highlights actions or procedures which, if not performed correctly, may lead to personal

injury or incorrect functioning of the instrument

!Note!

A note highlights actions or procedures which, if not performed correctly, may indirectly affect

operation or may lead to an instrument response which is not planned

Explosion protection

0Device certified for use in explosion hazardous area

If the device has this symbol embossed on its name plate it can be installed in an explosion hazardous

area

-Explosion hazardous area

Symbol used in drawings to indicate explosion hazardous areas. Devices located in and wiring

entering areas with the designation “explosion hazardous areas” must conform with the stated type

of protection.

.Safe area (non-explosion hazardous area)

Symbol used in drawings to indicate, if necessary, non-explosion hazardous areas. Devices located in

safe areas still require a certificate if their outputs run into explosion hazardous areas

Electrical symbols

%Direct voltage

A terminal to which or from which a direct current or voltage may be applied or supplied

&Alternating voltage

A terminal to which or from which an alternating (sine-wave) current or voltage may be applied or

supplied

)Grounded terminal

A grounded terminal, which as far as the operator is concerned, is already grounded by means of an

earth grounding system

*Protective grounding (earth) terminal

A terminal which must be connected to earth ground prior to making any other connection to the

equipment

+Equipotential connection (earth bonding)

A connection made to the plant grounding system which may be of type e.g. neutral star or

equipotential line according to national or company practice

Temperature resistance of the connection cables

States, that the connection cables must be resistant to a temperature of at least 85 °C.

t >85°C

Identification Micropilot M FMR245 with FOUNDATION Fieldbus

6Endress+Hauser

2 Identification

2.1 Device designation

2.1.1 Nameplate

The following technical data are given on the instrument nameplate:

L00-FMR2xxxx-18-00-00-en-003

Fig. 1: Information on the nameplate of the Micropilot M with Foundation Fieldbus (example)

2.1.2 Ordering structure

Ordering structure Micropilot M FMR 245

10 Approval:

A Non-hazardous area

F Non-hazardous area, WHG

2 ATEX II 1/2 G EEx ia IIC T6, XA, IECEx Zone 0/1

Note safety instruction (XA) (electrostatic charging)!

7 ATEX II 1/2 G EEx ia IIC T6, WHG, XA, IECEx Zone 0/1

Note safety instruction (XA) (electrostatic charging)!

5 ATEX II 1/2 G EEx d [ia] IIC T6, XA, IECEx Zone 0/1

Note safety instruction (XA) (electrostatic charging)!

G ATEX II 3 G EEx nA II T6

H ATEX II 1/2G EEx ia IIC T6, ATEX 3D, XA,

Note safety instruction (XA) (electrostatic charging)!

S FM IS - Cl.I Div.1 Gr. A-D

T FM XP - Cl.I Div.1 Group A-D

N CSA General Purpose

U CSA IS - Cl.I Div.1 Group A-D

V CSA XP - Cl.I Div.1 Group A-D

K TIIS EEx ia IIC T4

L TIIS EEx d [ia] IIC T4

YSpecialversion

20 Antenna:

3 50mm/2"

4 80mm/3"

9 Special version

FMR 245- Product designation (part 1)

Micropilot M FMR245 with FOUNDATION Fieldbus Identification

Endress+Hauser 7

Ordering structure Micropilot M FMR 245 (continued)

30 Process connection:

CFK DN50 PN10/16, PTFE>316L flange EN1092-1 (DIN2527)

CMK DN80 PN10/16, PTFE>316L flange EN1092-1 (DIN2527)

CQK DN100 PN10/16, PTFE>316L flange EN1092-1 (DIN2527)

CWK DN150 PN10/16, PTFE>316L flange EN1092-1 (DIN2527)

AEK 2" 150lbs, PTFE>316L flange ANSI B16.5

ALK 3" 150lbs, PTFE>316L flange ANSI B16.5

APK 4" 150lbs, PTFE>316L flange ANSI B16.5

AVK 6" 150lbs, PTFE>316L flange ANSI B16.5

KEK 10K 50A, PTFE>316L flange JIS B2220

KLK 10K 80A, PTFE>316L flange JIS B2220

KPK 10K 100A, PTFE>316L flange JIS B2220

KVK 10K 150A, PTFE>316L flange JIS B2220

TDK Tri-Clamp ISO2852 DN51 (2"), PTFE>316L

TEK Tri-Clamp ISO2852 DN63.5 (2-1/2"), PTFE>316L

TFK Tri-Clamp ISO2852 DN76.1 (3"), PTFE>316L

YY9 Special version

40 Output; Operation:

A 4-20mA HART; 4-line display VU331, envelope curve display on site

SIL2, IEC61508/IEC61511-1

B 4-20mA HART; w/o display, via communication

SIL2, IEC61508/IEC61511-1

K 4-20mA HART; Prepared for FHX40, remote display (Accessory)

SIL2, IEC61508/IEC61511-1

C PROFIBUS PA; 4-line display VU331, envelope curve display on site

D PROFIBUS PA; w/o display, via communication

L PROFIBUS PA; Prepared for FHX40, remote display (Accessory)

E FOUNDATION Fieldbus; 4-line display VU331, envelope curve display on site

F FOUNDATION Fieldbus; w/o display, via communication

M FOUNDATION Fieldbus; Prepared for FHX40, remote display (Accessory)

Y Special version

50 Housing:

A F12 Alu, coated IP65 NEMA4X

B F23 316L IP65 NEMA4X

C T12 Alu, coated IP65 NEMA4X, separate conn. compartment

D T12 Alu, coated IP65 NEMA4X+OVP, separate conn. compartment,

OVP=overvoltage protection

Y Special version

60 Cable entry:

2GlandM20

3ThreadG1/2

4ThreadNPT1/2

5PlugM12

6 Plug 7/8"

9 Special version

70 Additional option:

A Basic version

S GL/ABS/NK marine certificate

YSpecialversion

FMR 245- Complete product designation

Identification Micropilot M FMR245 with FOUNDATION Fieldbus

8Endress+Hauser

2.2 Scope of delivery

"Caution!

It is essential to follow the instructions concerning the unpacking, transport and storage of

measuring instruments given in the chapter "Incoming acceptance, transport, storage" on Page 10!

The scope of delivery consists of:

• Assembled instrument

• 2 ToF Tool - FieldTool®Package CD-ROMs

– CD 1: ToF Tool - FieldTool®Program

Program including Device Descriptions (device drivers) for all Endress+Hauser devices wich are

operable using ToF Tool

– CD 2: ToF Tool - FieldTool®Documentation

Documentation for all Endress+Hauser devices wich are operable using ToF Tool)

• Accessories (→Chap. 8)

Accompanying documentation:

• Short manual (basic setup/troubleshooting): housed in the instrument

• Operating manual (this manual)

• Approval documentation: if this is not included in the operating manual.

!Note!

The operating manual "Description of Instrument Functions" you can be found on the enclosed CD-

ROM.

2.3 Certificates and approvals

CE mark, declaration of conformity

The device is designed to meet state-of-the-art safety requirements, has been tested and left the

factory in a condition in which it is safe to operate. The device complies with the applicable

standards and regulations as listed in the EC declaration of conformity and thus complies with the

statutory requirements of the EG directives. Endress+Hauser confirms the successful testing of the

device by affixing to it the CE mark.

2.4 Registered trademarks

KALREZ®, VITON®, TEFLON®

Registered trademark of the company, E.I. Du Pont de Nemours & Co., Wilmington, USA

TRI-CLAMP®

Registered trademark of the company, Ladish & Co., Inc., Kenosha, USA

ToF®

Registered trademark of the company Endress+Hauser GmbH+Co. KG, Maulburg, Germany

PulseMaster®

Registered trademark of the company Endress+Hauser GmbH+Co. KG, Maulburg, Germany

PhaseMaster®

Registered trademark of the company Endress+Hauser GmbH+Co. KG, Maulburg, Germany

Foundation™ Fieldbus

Registered trademark of Fieldbus Foundation Austin, Texas, USA

Micropilot M FMR245 with FOUNDATION Fieldbus Mounting

Endress+Hauser 9

3Mounting

3.1 Quick installation guide

L00-FMR245xx-17-00-00-en-001

DN50

ANSI 2”

DN50

ANSI 2”

DN50

ANSI 2”

DN80…150

ANSI 3…6”

DN80…150

ANSI 3…6”

DN80…150

ANSI 3…6”

90°

F12/F23 housing

T12 housing

mark at instrument flange

Turn housing

Observe orientation when installing!

Installation in tank (free space):

Mark on process connector facing the nearest tank wall!

Installation in stilling well:

Mark on process connector pointed towards the slots or vent holes!

Installation in bypass:

Mark on process connector 90° offset from the tank connections!

The housing can be turned 350°

in order to simplify access to the

display and the terminal compartment

Allen key

4 mm/0.1”

Mounting Micropilot M FMR245 with FOUNDATION Fieldbus

10 Endress+Hauser

3.2 Incoming acceptance, transport, storage

3.2.1 Incoming acceptance

Check the packing and contents for any signs of damage.

Check the shipment, make sure nothing is missing and that the scope of supply matches your order.

3.2.2 Transport

"Caution!

Follow the safety instructions and transport conditions for instruments of more than

18 kg.

Do not lift the measuring instrument by its housing in order to transport it.

3.2.3 Storage

Pack the measuring instrument so that is protected against impacts for storage and transport. The

original packing material provides the optimum protection for this.

The permissible storage temperature is -40 °C…+80 °C.

Otros manuales para Micropilot M FMR245

Tabla de contenidos

Otros manuales de Radar de Endress+Hauser

Endress+Hauser

Endress+Hauser Micropilot M FMR245 Manual de usuario

Endress+Hauser

Endress+Hauser Hart Micropilot FMR60B Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Instrucciones de instalación

Endress+Hauser

Endress+Hauser Levelflex FMP55 Manual de usuario

Endress+Hauser

Endress+Hauser FOUNDATION Fieldbus Micropilot FMR53 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Micropilot S FMR530 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Micropilot FMR20 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Hart Micropilot FMR60B Manual

Endress+Hauser

Endress+Hauser Levelflex M FMP43 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Micropilot FMR62B PROFINET with Ethernet-APL Especificaciones técnicas

Endress+Hauser

Endress+Hauser Levelflex FMP55 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR10 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR53 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Micropilot FMR20 Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex FMP51 Especificaciones técnicas

Endress+Hauser

Endress+Hauser FOUNDATION Fieldbus Micropilot FMR51 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Levelflex FMP51 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR50 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Levelflex FMP50 Instrucciones de instalación

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR62B PROFINET with Ethernet-APL Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR60B PROFIBUS PA Manual de usuario

Manuales populares de Radar de otras marcas

SAW D2L

SAW D2L Valentine One Gen2 Manual de usuario

Raymarine

Raymarine Raytheon R20X Manual de usuario

Simrad

Simrad CA34 Manual de usuario

ECHOMAX

ECHOMAX Active-X-Band Manual de usuario

AGD

AGD 340 Manual de usuario

Kustom Signals

Kustom Signals Eagle 3 Manual de usuario

SYMEO

SYMEO STU Manual de usuario

Axis

Axis D2110-VE Manual de usuario

MALA

MALA MIRA Manual de usuario

Emerson

Emerson ROSEMOUNT 5300 Manual de usuario

Rosemount

Rosemount 5300 Series Manual de usuario

TERMA

TERMA SCANTER 5102 Manual de usuario

GSSI

GSSI UtilityScan Manual de usuario

Acconeer

Acconeer A111 Manual de usuario

Crosley

Crosley CR37 Manual de usuario

AGD

AGD 318 Manual de usuario

Cobra

Cobra SLR 650G Manual de usuario

Faselase

Faselase D10 Manual de usuario