Table of contents
4 Endress+Hauser
9.4 Block model .......................... 63
9.4.1 Blocks of the device software ....... 63
9.4.2 Block configuration when device is
delivered ...................... 64
9.5 Assignment of the measured values
(CHANNEL) in an AI Block ............... 64
9.6 Index tables of Endress+Hauser parameters .. 65
9.6.1 Setup Transducer Block ........... 65
9.6.2 Advanced Setup Transducer Block ... 66
9.6.3 Display Transducer Block .......... 67
9.6.4 Diagnostic Transducer Block ....... 68
9.6.5 Expert Configuration Transducer
Block ........................ 69
9.6.6 Expert Information Transducer
Block ........................ 71
9.6.7 Service Sensor Transducer Block .... 72
9.6.8 Service Information Transducer
Block ........................ 72
9.6.9 Data Transfer Transducer Block ..... 72
9.7 Methods ............................ 74
10 Commissioning via wizard ......... 75
11 Commissioning via operating
menu ............................. 76
11.1 Installation and function check ............ 76
11.2 Setting the operating language ............ 76
11.3 Configuration of an interface measurement .. 77
11.4 Recording the reference curve ............ 79
11.5 Configuration of the on-site display ........ 80
11.5.1 Factory settings of the on-site
display for interface measurements .. 80
11.5.2 Adjustment of the on-site display ... 80
11.6 Configuration management .............. 81
11.7 Protection of the settings against
unauthorized changes .................. 82
12 Commissioning (block-based
operation) ........................ 83
12.1 Function check ....................... 83
12.2 Block configuration .................... 83
12.2.1 Preparatory steps ............... 83
12.2.2 Configuring the Resource Block ..... 83
12.2.3 Configuring the Transducer Blocks ... 83
12.2.4 Configuring the Analog Input
Blocks ........................ 84
12.2.5 Additional configuration .......... 84
12.3 Scaling of the measured value in an AI Block .. 84
12.4 Language selection .................... 85
12.5 Configuration of an interface measurement .. 85
12.6 Configuration of the on-site display ........ 88
12.6.1 Factory settings of the on-site
display for interface measurements .. 88
12.7 Configuration management .............. 88
12.8 Configuration of the event behavior
according to the FOUNDATION Fieldbus
specification FF912 .................... 90
12.8.1 Groups of events ................ 91
12.8.2 Allocation parameters ............ 93
12.8.3 Configurable area ............... 96
12.8.4 Transmission of the event messages
to the bus ..................... 97
12.9 Protection of the settings against
unauthorized changes .................. 97
13 Diagnostics and troubleshooting ... 98
13.1 General trouble shooting ................ 98
13.1.1 General errors .................. 98
13.1.2 Parametrization errors ........... 99
13.2 Diagnostic information on local display ..... 100
13.2.1 Diagnostic message ............. 100
13.2.2 Calling up remedial measures ..... 102
13.3 Diagnostic event in the operating tool ...... 103
13.4 Diagnostic messages in the DIAGNOSTIC
Transducer Block (TRDDIAG) ............ 103
13.5 Diagnostic list ....................... 103
13.6 Event logbook ....................... 104
13.6.1 Event history .................. 104
13.6.2 Filtering the event logbook ....... 104
13.6.3 Overview of information events .... 104
13.7 Firmware history ..................... 106
14 Maintenance .................... 107
14.1 Exterior cleaning ..................... 107
14.2 Cleaning coax probes .................. 107
15 Repairs .......................... 108
15.1 General information on repairs ........... 108
15.1.1 Repair concept ................ 108
15.1.2 Repairs to Ex-approved devices .... 108
15.1.3 Replacement of an electronics
module ...................... 108
15.1.4 Replacement of a device ......... 108
15.2 Spare parts ......................... 109
15.3 Return ............................. 109
15.4 Disposal ........................... 109
16 Accessories ...................... 110
16.1 Device-specific accessories .............. 110
16.1.1 Weather protection cover ........ 110
16.1.2 Mounting bracket for the electronics
housing ..................... 111
16.1.3 Centering star ................. 111
16.1.4 Remote display FHX50 .......... 112
16.1.5 Overvoltage protection .......... 113
16.2 Communication-specific accessories ....... 114
16.3 Service-specific accessories .............. 114
16.4 System components ................... 114
