Endress+Hauser OUSAF44 Manual de usuario

Products Solutions Services

Operating Instructions

OUSAF44

Optical sensor with the OUA260 flow assembly for

the measurement of UV absorption

BA00416C/07/EN/18.22-00

71596229

2022-10-31

OUSAF44 Table of contents

Endress+Hauser 3

Table of contents

1 About this document ........... 4

1.1 Warnings ........................... 4

1.2 Symbols ............................ 4

1.3 Symbols on the product ............... 4

2 Basic safety instructions ....... 5

2.1 Requirements for the personnel ........ 5

2.2 Intended use ........................ 5

2.3 Workplace safety .................... 5

2.4 Operational safety ................... 5

2.5 Product safety ....................... 6

3 Product description ............. 7

3.1 Sensor design ....................... 7

3.2 Measuring principle .................. 8

4 Incoming acceptance and

product identification .......... 9

4.1 Incoming acceptance ................. 9

4.2 Product identification ................. 9

4.3 Manufacturer address ............... 10

4.4 Scope of delivery .................... 10

5 Mounting ...................... 10

5.1 Mounting requirements .............. 10

5.2 Mounting the sensor ................ 13

5.3 Post-mounting check ................ 14

6 Electrical connection .......... 14

6.1 Connecting the sensor ............... 15

6.2 Lamp voltage ....................... 15

6.3 Versions for use in hazardous areas .... 16

6.4 Ensuring the degree of protection ..... 18

6.5 Post-connection check ............... 19

7 Commissioning ................ 20

7.1 Function check ..................... 20

7.2 Calibrating/adjusting the sensor ...... 20

8 Maintenance .................. 23

8.1 Maintenance schedule ............... 23

8.2 Replacing the hazardous area lamp .... 23

8.3 Replacing the mercury lamp .......... 23

8.4 Replacing the reference filter ......... 26

8.5 Replacing the measurement filter ..... 28

8.6 Replacing the sensor window and seal .. 30

9 Repair .......................... 34

9.1 General information ................. 34

9.2 Spare parts ........................ 34

9.3 Return ............................ 34

9.4 Disposal ........................... 35

10 Accessories .................... 35

10.1 Flow assembly ...................... 35

10.2 Cable ............................. 36

10.3 Calibration ......................... 36

11 Technical data ................. 36

11.1 Input .............................. 36

11.2 Environment ....................... 37

11.3 Process ............................ 37

11.4 Mechanical construction ............. 37

Index ................................. 39

About this document OUSAF44

4 Endress+Hauser

1 About this document

1.1 Warnings

Structure of information Meaning

LDANGER

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation will result in a fatal or serious injury.

LWARNING

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation can result in a fatal or serious injury.

LCAUTION

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or more serious injuries.

NOTICE

Cause/situation

If necessary, Consequences of non-

compliance (if applicable)

‣Action/note

This symbol alerts you to situations which may result in damage to property.

1.2 Symbols

Additional information, tips

Permitted

Recommended

Forbidden or not recommended

Reference to device documentation

Reference to page

Reference to graphic

 Result of a step

1.3 Symbols on the product

Reference to device documentation

Warning: UV radiation

Do not dispose of products bearing this marking as unsorted municipal waste. Instead, return them to the

manufacturer for disposal under the applicable conditions.

OUSAF44 Basic safety instructions

Endress+Hauser 5

2 Basic safety instructions

2.1 Requirements for the personnel

• Installation, commissioning, operation and maintenance of the measuring system may be

carried out only by specially trained technical personnel.

• The technical personnel must be authorized by the plant operator to carry out the specified

activities.

• The electrical connection may be performed only by an electrical technician.

• The technical personnel must have read and understood these Operating Instructions and

must follow the instructions contained therein.

• Faults at the measuring point may only be rectified by authorized and specially trained

personnel.

Repairs not described in the Operating Instructions provided must be carried out only

directly at the manufacturer's site or by the service organization.

2.2 Intended use

The sensor measures the spectral absorption of process liquids in the ultraviolet region of the

electromagnetic spectrum. The sensor is suitable for use in a wide range of applicationsin a

variety of industrial sectors , such as:

• Measurement of protein concentrations

• Chromatography monitoring

• Filtration monitoring

• Concentration measurement of organic compounds

• Detection of aromates

Use of the device for any purpose other than that described, poses a threat to the safety of

people and of the entire measuring system and is therefore not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Workplace safety

As the user, you are responsible for complying with the following safety conditions:

• Installation guidelines

• Local standards and regulations

• Regulations for explosion protection

Electromagnetic compatibility

• The product has been tested for electromagnetic compatibility in accordance with the

applicable international standards for industrial applications.

• The electromagnetic compatibility indicated applies only to a product that has been

connected in accordance with these Operating Instructions.

2.4 Operational safety

Before commissioning the entire measuring point:

1. Verify that all connections are correct.

Basic safety instructions OUSAF44

6 Endress+Hauser

2. Ensure that electrical cables and hose connections are undamaged.

3. Do not operate damaged products, and protect them against unintentional operation.

4. Label damaged products as defective.

During operation:

‣If faults cannot be rectified:

products must be taken out of service and protected against unintentional operation.

2.5 Product safety

LCAUTION

Mercury lamp

Can cause damage to the eyes and skin!

‣Avoid any exposure of the eyes and skin to the unshielded product.

‣Wear suitable protective goggles to protect against UV radiation.

2.5.1 State-of-the-art technology

The product is designed to meet state-of-the-art safety requirements, has been tested, and

left the factory in a condition in which it is safe to operate. The relevant regulations and

international standards have been observed.

2.5.2 Versions with hazardous area lamp

‣Observe the safety instructions in the XA pertaining to this manual.

Safety instructions for electrical equipment in hazardous areas, photometer sensors,

XA01403C

OUSAF44 Product description

Endress+Hauser 7

3 Product description

3.1 Sensor design

1 12 34

A0030202

 1 Sensor with flow assembly OUA260

1 Cable connector

2 Lamp module

3 Flow assembly OUA260 (depending on version)

4 Detector module

The detector and lamp can vary on account of the individual options ordered.

Product description OUSAF44

8 Endress+Hauser

3.2 Measuring principle

Light absorption

The measuring principle is based on the Lambert-Beer law.

There is a linear dependency between the absorption of light and the concentration of the

absorbing substance:

A = -log(T) = ε . c . OPL

T = I/I0

T ... Transmission

I ... Intensity of received light at detector

I0 ... Intensity of transmitted light of light source

A ... Absorption

ε ... Extinction coefficient

c ... Concentration

OPL ... Optical path length

A light source emits radiation through the medium and the incident radiation is measured on

the detector side.

Once the light has passed through a filter for wavelength selection, the intensity of the light is

determined by a photodiode and converted to a photocurrent.

The subsequent conversion to transmission (%) or absorbance units (AU, OD) is performed in

the associated transmitter.

1OPL

68 7 2

A0029412

 2 Absorption measurement with reference

1 Light source

2 Optical windows

3 Measurement filter

4 Measuring detector

5 Lens

6 Medium flow

7 Reference filter

8 Reference detector

OUSAF44 Incoming acceptance and product identification

Endress+Hauser 9

4 Incoming acceptance and product identification

4.1 Incoming acceptance

1. Verify that the packaging is undamaged.

 Notify the supplier of any damage to the packaging.

Keep the damaged packaging until the issue has been resolved.

2. Verify that the contents are undamaged.

 Notify the supplier of any damage to the delivery contents.

Keep the damaged goods until the issue has been resolved.

3. Check that the delivery is complete and nothing is missing.

 Compare the shipping documents with your order.

4. Pack the product for storage and transportation in such a way that it is protected

against impact and moisture.

 The original packaging offers the best protection.

Make sure to comply with the permitted ambient conditions.

If you have any questions, please contact your supplier or your local Sales Center.

4.2 Product identification

4.2.1 Nameplate

The nameplate provides you with the following information on your device:

• Manufacturer identification

• Order code

• Serial number

• Safety information and warnings

‣Compare the information on the nameplate with the order.

4.2.2 Product identification

Product page

www.endress.com/ousaf44

Interpreting the order code

The order code and serial number of your product can be found in the following locations:

• On the nameplate

• In the delivery papers

Obtaining information on the product

1. Go to www.endress.com.

2. Page search (magnifying glass symbol): Enter valid serial number.

Mounting OUSAF44

10 Endress+Hauser

3. Search (magnifying glass).

 The product structure is displayed in a popup window.

4. Click the product overview.

 A new window opens. Here you fill information pertaining to your device, including

the product documentation.

4.3 Manufacturer address

Endress+Hauser Conducta Inc.

4123 East La Palma Avenue, Suite 200

Anaheim, CA 92807 USA

4.4 Scope of delivery

The scope of delivery comprises the following, depending on the version ordered:

• Detector and lamp module without flow assembly or

• Detector and lamp module mounted on flow assembly OUA260

• Operating Instructions

‣If you have any queries:

Please contact your supplier or local sales center.

5 Mounting

5.1 Mounting requirements

5.1.1 Measuring system

An optical measuring system comprises:

• Sensor (photometer) OUSAF44

• Transmitter, e. g. Liquiline CM44P

• Cable set, e. g. CUK80

• Assembly OUA260

Otros manuales para OUSAF44

Tabla de contenidos

Otros manuales de Instrumento de medición de Endress+Hauser

Endress+Hauser

Endress+Hauser RIA16 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Proline Promass series Especificaciones técnicas

Endress+Hauser

Endress+Hauser Turbimax CUE25 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic M FMU44 Manual de usuario

Endress+Hauser

Endress+Hauser Proline t-mass 65 PROFIBUS DP Manual de usuario

Endress+Hauser

Endress+Hauser Liquitrend QMW43 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promass E 200 Manual de usuario

Endress+Hauser

Endress+Hauser QWX43 Manual del operador

Endress+Hauser

Endress+Hauser memo-graph RSG10 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Prowirl F 200 Manual de usuario

Endress+Hauser

Endress+Hauser RIA452 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Prothermo NMT 538 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Prowirl 200 Instrucciones de instalación

Endress+Hauser

Endress+Hauser COM 381 Manual de usuario

Endress+Hauser

Endress+Hauser Flowfit CYA27 Manual de usuario

Endress+Hauser

Endress+Hauser Promag 400 Index C Manual de usuario

Endress+Hauser

Endress+Hauser Nanomass Gas Density Manual de usuario

Endress+Hauser

Endress+Hauser Raman Rxn2 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag H 200 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Prosonic T FMU30 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promass E TB2 HART Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR51 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Proline Promag 50D Manual

Endress+Hauser

Endress+Hauser Proline Promass O 500 PROFIBUS DP Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario

R&S

R&S ZPH Manual de usuario